Casio EQW-M1100DB-1AER Manual

Casio Ur EQW-M1100DB-1AER

Læs gratis den danske manual til Casio EQW-M1100DB-1AER (6 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Casio EQW-M1100DB-1AER, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Operation Guide 5122

MA1005-EA

Congratulations upon your selection of this CASIO watch.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours. Because of this, the radio-controlled atomic timekeeping function will not

display the correct time for Newfoundland, Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

About This Manual

Left Dial hand



B +

*> 56

Button operations are indicated using the letters A

through shown in the illustration.D

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Left Dial hand:

Indicates the current mode ( , , , ).TM ST WT AL

b Right Dial Hands:

Indicate a time, in 24-hour format,

depending on the current mode.

n 24-hour Hand:

Indicates the current 24-hour timekeeping hour.

m Day

This User’s Guide uses numbers shown above to identify

watch hands and indicators.

Things to check before using the watch

1. Hold down at least two seconds to enter the Timekeeping Mode, and C

then observe the movement of the

x .Second Hand

Is the moving smoothly at one-second intervals?xSecond Hand

Is the moving at xSecond Hand

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged sufﬁciently.

For details about charging, see

“Charging the Watch”.

Power is low. Charge the watch by placing

it in a location where it is exposed to light.

For details, see “Charging the Watch”.

YES

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁgure summer time and other Home City settings” to

conﬁgure your Home City and daylight saving time settings.

Important!

Proper time calibration signal reception and World Time settings depend on correct

Home City, time, and date settings in the Timekeeping Mode. Make sure you

conﬁgure these settings correctly.

3. Set the current time.

•To set the time using a time calibration signal

See “To get ready for a receive operation”.

•To set the time manually

See “Conﬁguring Current Time and Date Settings Manually”.

The watch is now ready for use.

For details about the watch’s radio controlled timekeeping feature, see “Radio •

Controlled Atomic Timekeeping”.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated

power charges a built-in rechargeable battery, which powers watch operations. The

watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not

wearing the watch, leave

it in a location where it is

exposed to light.

Best charging •

performance is achieved

by exposing the watch to

light that is as strong as

possible.

When wearing the watch,

make sure that its face is

not blocked from light by the

sleeve of your clothing.

The watch may enter a •

sleep state if its face is

blocked by your sleeve

even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become

particularly hot when exposed to the following conditions for long periods.

On the dashboard of a car parked in direct sunlight •

Too close to an incandescent lamp •

Under direct sunlight •

Important!

Keep the watch in an area normally exposed to bright light when storing it for long •

periods. This helps to ensure that power does not run down.

Storing the watch for long periods in an area where there is no light or wearing it in •

such a way that it is blocked from exposure to light can cause power to run down.

Make sure that the watch is exposed to bright light whenever possible.

Power Levels

You can get an idea of the watch’s power level by

observing the movement of the

x in the Second Hand

Timekeeping Mode.

If the •x is moving normally at one-second Second Hand

intervals, power is at Level 1.

If the •x is moving at two-second intervals, Second Hand

power is at Level 2, which is quite low. Expose the watch

to light as soon as possible so it can charge.

Level Hand Movement Function Status

1 Normal. All functions enabled

x moves at two-second Second Hand

intervals.

m changes to (home position).Day 1

Beeper, time calibration signal

reception disabled

x stopped.Second Hand

z and Hour Hand cMinute Hand

stopped at 12 o’clock.

All functions disabled

When power drops to Level 3, all functions will be disabled but the watch will •

continue to keep time internally for about one week. If you recharge the battery

sufﬁciently during this period, the analog hands will move automatically to the

correct setting and regular timekeeping will resume. After one week, all settings

(including timekeeping) will be cleared. Recharging the battery will reset all settings

to their initial factory defaults.

Power Recovery Mode

The watch is designed to go into a power recovery mode that stops hand operation

temporarily whenever power suddenly drops below a certain level due to overuse

of the alarm tone over a short period. Note that all operations are disabled while the

watch is in the power recovery mode.

The hands will move to the correct positions and the watch will resume normal

operation after power recovers (in about 15 minutes). Putting the watch in a location

where it is exposed to light will help power to recover sooner.

Charging Times

Exposure Level (Brightness) Daily

Operation

Level Change *2

Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 minutes 2 hours 23 hours

Window sunlight (10,000 lux) 30 minutes 6 hours 85 hours

Window sunlight on cloudy day

(5,000 lux) 48 minutes 8 hours 138 hours

Indoor ﬂuorescent lighting (500 lux) 8 hours 92 hours – – –

1 Approximate exposure each day to generate power for normal daily operation. *

2 Approximate exposure to take power up one level. *

The above times are for reference only. Actual times depend on lighting conditions. •

For details about the operating time and daily operating conditions, see the “Power •

Supply” section of the Speciﬁcations.

Power Saving

Power Saving enters a sleep state automatically whenever the watch is left for a

certain period in an area where it is dark. The table below shows how watch functions

are affected by Power Saving.

There actually are two sleep state levels: “second hand sleep” and “function sleep”. •

Elapsed Time in Dark Operation

60 to 70 minutes (second hand sleep) x only stopped at 12 o’clock, all Second Hand

other functions enabled

6 or 7 days (function sleep)

All functions, including analog timekeeping, •

disabled

Internal timekeeping maintained •

The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch •

is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep

state.

The watch will not enter a sleep state while it is in the Stopwatch Mode. •

To recover from the sleep state

Move the watch to a well-lit area or press any button.

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

However, when using the watch outside of areas covered by time calibration signals,

you will have to adjust the settings manually as required. See “Conﬁguring Current

Time and Date Settings Manually” for more information.

This section explains how the watch updates its time settings when the city code

selected as the Home City is in Japan, North America, Europe, or China, and is one

that supports time calibration signal reception.

If your Home City code setting is this: The watch can receive the signal from the

transmitter located here:

LON, PAR, ATH Anthorn (England), Mainﬂingen (Germany)

HKG Shangqiu City (China)

TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, LAX, DEN, CHI, NYC Fort Collins, Colorado (United States)

Important!

The areas covered by •HNL ANC and are quite far from the calibration signal

transmitters, so certain conditions may cause reception problems.

When •HNL HKG or is selected as the Home City, only the time and date are

adjusted according to the time calibration signal. You need to switch manually

between standard time and daylight saving time (DST) if required.

See “To conﬁgure summer time and other Home City settings” for information about

how to do this.

Moves at two-second

intervals.



B +

Operation Guide 5122

Approximate Reception Ranges

UK and German Signals U.S. Signal

Anthorn

500 kilometers

1,500 kilometers

Mainﬂingen

The Anthorn signal is receivable

within this area.

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

Japanese Signals Chinese Signal

Fukushima

500 kilometers

1,000 kilometers

Fukuoka/Saga

1,500 kilometers

Changchun500 kilometers

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

Even when the watch is within range of a transmitter, signal reception may be •

impossible due to the effects of geographic contours, structures, weather, the time

of year, the time of day, radio interference, etc. The signal becomes weaker at

distances of approximately 500 kilometers, which means that the inﬂuence of the

above conditions becomes even greater.

Signal reception may not be possible at the distances noted below during certain •

times of the year or day. Radio interference may also cause problems with reception.

Mainﬂingen (Germany) or Anthorn (England) transmitters: 500 kilometers −

(310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers) −

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles) −

Shangqiu (China) transmitter: 500 kilometers (310 miles) −

As of March 2010, China does not use Daylight Saving Time (DST). If China does •

go to the Daylight Saving Time system in the future, some functions of this watch

may no longer operate correctly.

Using this watch in a country covered by a time calibration signal that is different •

from the countries it supports may result in incorrect time indication due to local

application of summer time, etc.

To get ready for a receive operation

Conﬁrm that the watch is in the Timekeeping Mode. If it isn’t, hold down 1. at least C

two seconds to enter the Timekeeping Mode.

The antenna of this watch is located on its 12 o’clock side. Position the watch with 2.

12 o’clock facing towards a window as shown in the nearby illustration. Make sure

there are no metal objects nearby.

12 o’clock

Signal reception normally is better •

at night.

The receive operation takes from two •

to seven minutes, but in some cases

it can take as long as 14 minutes.

Take care that you do not perform

any button operation or move the

watch during this time.

Signal reception may be difﬁcult or •

even impossible under the conditions

described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁce

equipment,

or a mobile

phone

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near

high-tension

power lines

Among

or behind

mountains

What you should do next depends on whether you are using Auto Receive or 3.

Manual Receive.

Auto Receive: Leave the watch over night in the location you selected in step 2. •

See “Auto Receive” for details.

Manual Receive: Perform the operation under “To perform manual receive”. •

Auto Receive

With Auto Receive, the watch performs the receive operation each day •

automatically up to six times (up to ﬁve times for the Chinese calibration signal)

between the hours of midnight and 5 a.m. (according to the Timekeeping Mode

time). When any receive operation is successful, none of the other receive

operations for that day are performed.

When a calibration time is reached, the watch will perform the receive operation •

only if it is in the Timekeeping Mode or World Time Mode. The receive operation is

not performed if a calibration time is reached while you are conﬁguring settings.

To perform manual receive

In the Timekeeping Mode, keep 1. depressed (for about two seconds) as the D

x goes through the following sequence.Second Hand

Moves to •YES Y NO N (or for some models) or ( ) to indicate the last signal

reception result, then to ( ).READY R

The 2. indicates the operations the watch is currently performing.xSecond Hand

When the xSecond

Hand is pointed here: It means this:

READY (R) Watch is setting up for reception.

WORK (W) Reception is in progress.

If signal reception is unstable, the •x Second Hand

may move between ( ) and ( ). WORK W READY R

Regular timekeeping resumes after the receive operation 3.

is complete.

When the receive operation is successful, the watch •

adjusts the time setting accordingly. It does not adjust

the setting if the operation failed.

Note

To interrupt a receive operation and return to the •

Timekeeping Mode, press any button.

To check the result of the latest receive operation

In the Timekeeping Mode, press .D

The •x will move to ( ) for ﬁve Second Hand YES Y

seconds if the latest receive operation was successful,

or ( ) if it was not. After that, regular timekeeping NO N

will resume.

You can return to the Timekeeping Mode manually by •

pressing while the Dx is pointing to Second Hand YES

( ) or ( ).Y NO N

Note

The •x will indicate ( ) if you have Second Hand NO N

adjusted the time or date setting manually since the

latest receive operation.

Radio-controlled Atomic Timekeeping Precautions

Strong electrostatic charge can result in the wrong time setting. •

Even if a receive operation is successful, certain conditions can cause the time •

setting to be off by up to one second.

The watch is designed to update the date automatically for the period January 1, •

2000 to December 31, 2099. Updating of the date by signal reception will no longer

be performed starting from January 1, 2100.

If you are in an area where signal reception is not possible, the watch keeps time •

with the precision noted in “Speciﬁcations”.

The receive operation is disabled under any of the following conditions. •

While power is at Level 2 or lower −

While the watch is in the power recovery mode −

When the watch is in the function sleep state (“Power Saving”) −

A receive operation is cancelled if an alarm sounds while it is being performed. •

Mode Reference Guide

Your watch has four “modes”. The mode you should select depends on what you

want to do.

Note

There are also various setting modes, which you can enter by holding down •A in

the Timekeeping Mode. See “Setting Modes” for more information.

To do this: Enter this mode:

View the current time in your Home City and in one of 29 other •

cities around the globe

View the current date in the Home City •

Perform a time calibration receive operation •

Timekeeping Mode

Use the stopwatch to measure elapsed time Stopwatch Mode

Select one of 29 cities (time zones) around the world and view the •

current time there

Select daylight saving/summer time (DST) or standard time for a •

time zone

World Time Mode

Set an alarm time Alarm Mode

Selecting a Mode

With this watch, everything starts from the Timekeeping Mode.

To determine the watch’s current mode

Check the position of the v as shown under Left Dial hand

“To select a mode”.

To return to the Timekeeping Mode from any other

mode

Hold down for at least two seconds.C

To select a mode

Press to cycle between the modes as shown below. The Cv indicates the Left Dial

currently selected mode.

The v rotates so the indicator for the current mode ( , , , ) is Left Dial TM ST WT AL

aligned with the pointer .

Timekeeping Mode Stopwatch Mode

v v indicates .Left Dial TM indicates , then Left Dial ST

aligns the dial hand with the

pointer .

World Time Mode

v indicates , Left Dial WT

then aligns the dial hand with

STD DST or .

Alarm Mode

v indicates .Left Dial AL





Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	EQW-M1100DB-1AER
Vægt:	110 g
Dimensioner (BxDxH):	46.9 x 13.7 x 51.5 mm
Armbånd, materiale:	Resin
Urkassens materiale:	Rustfrit stål
Kalender:	Ja
Stopur:	Ja
Batteritype:	CTL920
Urets glastype:	Mineral
Alarmfunktion:	Ja
Vandbestandig dybde:	100 m
Verdenstid funktkon:	Ja
Radiosignal modtager:	DCF/MSF/WWVB/JJY/BPC
Solenergi:	Ja