Cateye Cordless 7 CC-FR7CL Manual

Cateye Cykel computer Cordless 7 CC-FR7CL

Læs gratis den danske manual til Cateye Cordless 7 CC-FR7CL (2 sider) i kategorien Cykel computer. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Cateye Cordless 7 CC-FR7CL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are

not expressly approved by Cat Eye Co., Ltd. may void the user’s authority to operate the equipment.

CAT EYE Cordless 7

CYCLOCOMPUTER CC-FR7CL

E OWNER’S MANUAL

Installation of Computer:

Secure bracket to handlebar with nylon ties (fig. A).

Slide computer into mount until it snaps in place.

Mount the wheel magnet to a spoke on the front

wheel (fig.B), so the magnet faces the sensor.

Secure the sensor to fork leg as shown (fig. C).

NOTE: The distance between the computer and the sen-

sor must not exceed 70 cm—if the sensor is too far

away from the computer head, the speed signal will not

For best results, mount the sensor as high on the fork

leg as reasonably possible, so that the sensor is within

transmission range to the computer. However, the sen-

sor must be close enough to spokes to allow proper dis-

tance to magnet (see below).

Test by spinning the front wheel. Computer screen

should show speed. If not, make sure the magnet is1)

close enough to sensor (within 5 mm); and 2) the sensor

is close enough to computer head (within 70 cm) and 3)

nothing is obstructing the line of sight between the sen-

sor and the computer head.

IMPORTANT! PLEASE READ INSTRUCTIONS COMPLETELY

BEFORE ATTEMPTING TO INSTALL AND USE YOUR CAT EYE

CORDLESS 7 COMPUTER.

Cordless 7

U.S. Pat. Nos.4633216/4636769/4642606/5236759 Pat. and Design Pat. Pending

CCMFR7CL-021210 Printed in Japan 066600165

Bracket

Sensor

(Transmitter)

Magnet

Nylon Ties (L x 2)

Nylon Ties (S x 2)

Sensor Pulse Indicator

Magnet's

center

Marking line

Less than 5mm

Spin

Max.

Distance

70 cm

NOTE: When the wheel rotates, the magnet MUST line up with the mark on the sensor.

ALSO NOTE: Magnet must pass within 5 mm of the sensor—if not, it will not trip the

sensor as it passes, and the computer will not register speed. Adjusting the sensor

position higher or lower on the fork leg or by rotating the sensor on the fork mount may

be required to achieve proper distance to the wheel magnet.

Press the SET button to lock in your choice--- ---OR

if you want to input previous mileage, hold the

MODE button for (before pressing the SET button)

2 seconds.

• Flashing Odometer digits will appear.

• MODE button increases the digit number.

• START/STOP button moves to the next digit.

• Press the SET button when complete.

Press All-Clear button (AC).

Computer Set-up (for first use, or after replacing battery)

Get your wheel

circumference

move to the next digit

• Stored data is erased.

• Computer power is started.

• Total Odometer read's "zero".

• All digits shown then fades.

• Flashing "km/h" remains.

Adjust between “mph” or “km/h” by pressing

the MODE button.

• Wheel circumference number is shown.

• Look at chart to find TIRE SIZE in "mm".

• To increase TIRE SIZE press MODE button.

• To decrease press START/STOP button.

• 10-2999 mm can be registered.

• Press SET button when finished.

km/h mph

Setup Completed (To Tm)

Tire Size L(mm)

12 x1.75 935

14 x 1.50 1020

14 x 1.75 1055

16 x 1.50 1185

16 x 1.75 1195

18 x 1.50 1340

18 x 1.75 1350

20 x 1.75 1515

20 x 1-3/8 1615

22 x 1-3/8 1770

22 x 1-1/2 1785

24 x 1 1753

24 x 3/4Tubular 1785

24 x 1-1/8 1795

24 x 1-1/4 1905

24 x 1.75 1890

24 x 2.00 1925

24 x 2.125 1965

26 x 7/8 1920

26 x 1(59) 1913

26 x 1(65) 1952

26 x 1.25 1953

26 x 1-1/8 1970

26 x 1-3/8 2068

26 x 1-1/2 2100

26 x 1.40 2005

26 x 1.50 2010

26 x 1.75 2023

26 x 1.95 2050

26 x 2.00 2055

26 x 2.10 2068

26 x 2.125 2070

26 x 2.35 2083

26 x 3.00 2170

27 x 1 2155

27 x 1-1/8 2161

27 x 1-1/4 2161

27 x 1-3/8 2169

650 x 35A 2090

650 x 38A 2125

650 x 38B 2105

700 x 18C 2070

700 x 19C 2080

700 x 20C 2086

700 x 23C 2096

700 x 25C 2105

700 x 28C 2136

700 x 30C 2170

700 x 32C 2155

700C Tubular 2130

700 x 35C 2168

700 x 38C 2180

700 x 40C 2200

increase

the figure

increase

the figure

AC Button

decrease

the figure

Use the below table

as the rough guide.

The tire size is marked on

both sides of the tire.

AC buttonSET button

ST./STOP button

MODE button

L mm

In this state Auto Time is ON.

ST./STOP

MODE

SET

MODE

Precautions

• Do not concentrate too much on the computer operations while riding.

• Be sure to securely mount the magnet, sensor and bracket on your bicycle,

and alweys check to insure they are mounted securely.

• Used batteries must be disposed of properly and in accordance with all

local regulations.

• Never disassemble the computer.

• For cleaning, use mild soap and a soft cloth. Wipe dry with a soft cloth. Paint

thinner, benzine, alcohol or other chemicals may damage the surface.

About cordless system

The sensor picks up the wheel revolution signal and transmits the signal to the computer; the

computer calculates and displays the data on the screen.

CAUTION: In order to prevent external signal interference, the signal reception range is limited. For

best performance, the distance between the sensor and the computer must be kept within 70cm.

Attach the sensor at the upper part of your fork so that the distance becomes less than 70cm. The

signal reception range may shorten as a result of low temperature or lowered battery power.

In the following places and circumstances, interference may occur, resulting in malfunction:

• Near railroad crossing; in train cars.

• Near other cordless devices/television/personal computer/high power lighting system.

• Near the places where strong electromagnetic wave is generated; near television/ radio station; near

radar base.

• When being very close to another bicycle which also has a cordless cyclocomputer on its handlebar.

Sensor Screw

Sensor Base

Front Fork

(fig. C)

(fig. B) Spoke

Lever

Slide

Click

(fig. A)

Mounting View

Front Fork

Produkt Specifikationer

Mærke:	Cateye
Kategori:	Cykel computer
Model:	Cordless 7 CC-FR7CL

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Cordless 7 CC-FR7CL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel computer Cateye Manualer

Cateye Vectra Wireless CC-VT100W Manual

4 September 2024

Cateye CC-RD430DW Strada Manual

3 September 2024

Cateye Quick CC-RS100W Manual

1 September 2024

Cateye Padrone+ CC-PA110W Manual

1 September 2024

Cateye Padrone Digital CC-PA400B Manual

1 September 2024

Cateye CC-RD410DW Strada Manual

31 August 2024

Cateye CC-RD400DW Strada Manual

26 August 2024

Cateye OS 1.1. Manual

12 August 2024

Cateye Velo Wireless Manual

5 August 2024

Cateye CC-AT200W Adventure Manual

2 August 2024

Cykel computer Manualer

Nyeste Cykel computer Manualer

Lezyne Micro C Manual

30 December 2025

BBB BCP-35W Manual

12 Oktober 2024

Crivit HG01734A Manual

3 Oktober 2024

Sigma Pure GPS Manual

2 Oktober 2024

Bryton Rider 20 Manual

2 Oktober 2024

Sigma BC 1600 Manual

30 September 2024

Lezyne Mega XL GPS Manual

29 September 2024

Wahoo Elemnt Roam v2 Manual

23 September 2024

Trelock BB 4000i Manual

23 September 2024

Echowell Ui-20 Manual

23 September 2024