Cateye Strada CC-RD300W Manual

Cateye Cykel computer Strada CC-RD300W

Læs gratis den danske manual til Cateye Strada CC-RD300W (2 sider) i kategorien Cykel computer. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Cateye Strada CC-RD300W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Tire circumference

reference table

12 x 1.75

14 x 1.50

14 x 1.75

16 x 1.50

16 x 1.75

18 x 1.50

18 x 1.75

20 x 1.75

20 x 1-3/8

22 x 1-3/8

22 x 1-1/2

24 x 1

24 x 3/4

Tubular

24 x 1-1/8

24 x 1-1/4

24 x 1.75

24 x 2.00

24 x 2.125

26 x 7/8

26 x 1(59)

26 x 1(65)

26 x 1.25

26 x 1-1/8

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.10

26 x 2.125

26 x 2.35

26 x 3.00

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 20C

650 x 23C

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 40C

29 x 2.1

29 x 2.3

935

1020

1055

1185

1195

1340

1350

1515

1615

1770

1785

1753

1785

1795

1905

1890

1925

1965

1920

1913

1952

1953

1970

2068

2100

2005

2010

2023

2050

2055

2068

2070

2083

2170

2145

2155

2161

2169

1938

1944

2090

2125

2105

2070

2080

2086

2096

2105

2136

2146

2155

2130

2168

2180

2200

2288

2326

Tire size L (mm)

CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending

CCRD3W-110930 066600542 6

L mm

SEN

SOR

ZONE

5 mm

SEN

SOR

ZON

Install the sensor and magnet

Sensor zone

Inside of right front fork

Max

70 cm

YES! NO!

The distance between the computer

and the sensor must not exceed the

transmission range of 70 cm. The back

of the computer must face the sensor.

The magnet

must pass

through the

sensor zone.

The clearance

between the

sensor surface

and the magnet

must not

exceed 5 mm.

SENSO R

ZONE

SENSOR

ZONE

1 2

Click

For wing type handlebar or oversized

stem, bracket can be mounted using

the Bracket Holder and nylon ties.

(Option)

Caution:

Make sure that the back of the computer faces the sensor.

* The computer may not function appropriately on some

stem if its back does not face the sensor as shown in

When attaching the bracket to the stem

Spoke

Toward the

sensor zone

Install the magnet

While supporting it by hand,

Handlebar

Cut

Attach the bracket to the stem or handlebar

Remove/install the

computer

Caution:

Round off the cut edge

of the bracket band to

prevent injury.

Install the sensor Inside of right front fork

* After installation, rotate the front wheel gently to check that the speed is displayed on the

computer. If the speed is not displayed, check that conditions

, and

, above, have

been done appropriately.

Stem

Pull

securely

* Install the sensor as close to the upper

part of the front fork as possible.

push it out as if lifting the front up

When attaching the bracket to the handlebar

How to install the unit on your bicycle

1Bracket band

2Bracket

3Nut

4Speed sensor

5Magnet

6Sensor rubber pad

7Bracket rubber pad

8Nylon ties (x2)

ENG

Before using the computer, please thoroughly read this manual and keep it for

future reference.

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these periodically.

• If a child swallows a battery, consult a doctor immediately.

• Do not leave the computer in direct sunlight for unnecessary or extended periods.

• Do not disassemble the computer.

• Do not drop the computer. Doing so may result in a computer malfunction or damage.

• When using the computer installed on the bracket, change the by pressing on the three dotsMODE

below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket

threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sunglass lenses.

Wireless Sensor

The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of

interference.

When adjusting the wireless sensor, note the following:

• Signals cannot be received if the distance between the sensor and the computer is too great.

• The transmission distance may be shorter due to low temperature or low battery.

• Signals can be received only when the back of the computer is facing the sensor.

Interference may occur, resulting in incorrect data, if the computer is:

• Near a TV, PC, radio, motor, or in a car or train.

• Close to a railroad crossing, railway tracks, TV stations and/or radar base.

• Using with other wireless devices in close proximity.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following

two conditions:(1)This device may not cause harmful interference,and (2)this device

must accept any interference received,including interference that may cause undesired

operation.

Modifications The FCC requires the user to be notified that any changes or modifications

made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user

’s authority to operate the equipment.

MODE

MENUMENUMENU

MODE

MODEMODEMODE

MODE

MODEMODEMODE

MODE

MENUMENUMENU

MODE

MODEMODEMODE

km/h ↔ mph

Increase Move digits

(by pressing

& holding)

setting

the setting

Clear all data (initialization)

Press the button on the back.AC

Select the desired speed units

Select “ ” or “ ”.

Enter the tire circumference

Enter the tire circumference of your bicycle in mm.

* Refer to the tire circumference reference table.

Set the clock

When MODE is pressed and held, “Displayed

time”, “Hour”, and “Minute” will appear, in

this order.

24h ↔ 12h,

or increase

the value

Switch the

screen or

move digits

(by pressing

& holding)

Preparing the computer

Battery case cover

Push!

When the computer is

mounted on the bracket

: Speed unit

: Wheel size icon

: Sensor signal reception icon

Measure wheel circumference

(L) of your bike

To get the most accurate

calibration do a wheel roll out.

With the valve stem

perpendicular to the ground,

mark the pavement at the valve

stem. With the riders weight on

the bike, roll the wheel one tire

revolution in a straight line and

mark the ground when the

valve stem is perpendicular to

the ground again. Measure the

distance in millimeters. This is

the most accurate wheel

calibration number.

#160-2190N

Parts kit

#160-2196

Speed sensor

#169-9691N

Wheel magnet

#160-0280N

Bracket band

#166-5150

Lithium battery (CR2032)

Optional parts

#160-2770

Bracket holder

#160-2193

Bracket

Standard parts

Wheel selection ..... Toggle between the specified wheel size (tire circumference)

and . Use this function if the computer is to be shared

between two bicycles.

................................ .Pressing MODE toggles between and

Wheel size entry .... Pressing MODE increases the value, and pressing and

holding moves to the next digit.MODE

* To enter the wheel size , display using Wheel selection“ ”.

Clock setting .......... To .set the clock, refer to “Preparing the computer-4”

Total distance manual entry

................................ Before reinitializing the computer, note the total distance. This

reading will later allow you to enter the total distance

manually. Pressing MODE increases the value, and pressing

and holding moves to the next digit.MODE

Speed unit .............. Pressing MODE toggles between and .

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and

wipe it off with a dry cloth.

Replacing the battery

Computer

If the display appears faded, replace the battery.

Install a new lithium battery (CR2032) with the (+)

side facing upward. Then reinitialize the computer

referring to Preparing the computer“ ”.

* When the battery is installed, place the inner seal

cap with the side upward.“TOP”

Sensor

If sensor reception is poor, replace the battery.

After replacement, check the positions of the sensor and magnet.

LIMITED WARRANTY

2-Year Computer only

(Accessories/Bracket sensor and Battery Consumption excluded)

CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years

from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no

charge. Service must be performed by CatEye or an authorized retailer.

To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for

repair. Please write or type your name and address clearly on the warranty certificate.

Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.

For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory

rights.

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn: CATEYE Customer Service

Phone : (06)6719-6863

Fax : (06)6719-6033

E-mail : support@cateye.co.jp

URL : http://www.cateye.com

[For US Customers]

CATEYE AMERICA, INC.

2825 Wilderness Place Suite 1200, Boulder CO80301-5494 USA

Phone : 303.443.4595

Toll Free : 800.5CATEYE

Fax : 303.473.0006

E-mail : service@cateye.com

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.

Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.

The sensor signal reception icon does not flash. (The speed is not displayed.)

(Spin the front wheel, bringing the computer closer to the sensor. If the icon now flashes, this indicates that the

computer and sensor are too far apart or that the battery is low.)

Is the clearance between the sensor and magnet too great? (must be

≤

5 mm)

Does the magnet pass through the sensor zone?

Adjust the positions of the magnet and sensor.

Is the computer installed at the correct angle?

Back of computer must face toward the sensor.

Are the computer and sensor too far apart? (The distance must not exceed 70 cm.)

Install the sensor closer to the computer.

Is the computer or sensor battery weak?

In winter, battery performance diminishes.

Replace the battery. In the case of the computer, after replacing the battery, re-start the computer according to the

“ ”Preparing the computer , above.

No display.

Is battery in the computer run down?

Replace it. Then reinitialize the computer referring to Preparing the computer“ ”.

Incorrect data appear.

Reinitialize the computer referring to “Preparing the computer”.

Specification

Battery ................. Computer : Lithium battery (CR2032) x 1

Sensor : Lithium battery (CR2032) x 1

Battery life ........... Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary

depending on the conditions of use.)

Sensor : Unit Total Distance reaches about 10,000 km (6,250 mile)

* This is the average figure of being used under 20 °C temperature and the distance between the computer and the

sensor is 65 cm.

Controller .................................. 4-bite, 1-chip microcomputer (Crystal controlled oscillator)

Display ...................................... Liquid crystal display

Sensor ...................................... No contact magnetic sensor

Wheel circumference range ..... 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)

Working temperature ............... 32 ° °F - 104 F (0 C - 40 C) (This product will not display appropriately when exceeding the° °

Working Temperature range. Slow response or black LCD at lower or higher temperature

may happen respectively.)

Dimensions/weight 1-53/64 x 1-7/32 x 5/8 (46.5 x 31 x 16 mm) / 0.78 oz (22 g)................... ” ” ”

* The factory-loaded battery life might be shorter than the above-mentioned specification.

* The specifications and design are subject to change without notice.

CC-RD300W

MODE

MODEMODEMODE MODE

MODE

MODEMODEMODE MODE

MODE

MODEMODEMODE MODE

MODE

MODEMODEMODE

MODE

MODEMODEMODE

MODE

Pace arrow

Indicates whether the current speed

is faster ( ) or slower ( ) than the

average speed.

Operating the computer [Measuring screen]

Tm Elapsed Time

0:00 00 59’ ” - 9:59’ ”

Dst Trip Distance

0.00 - 999.99 km [mile]

Dst

Trip Distance-2

0.00 - 999.99 /

1000.0 - 9999.9 km [mile]

Av Average Speed*2

0.0 - 105.9 km/h

[0.0 - 65.9 mph]

Mx Maximum Speed

0.0(4.0) - 105.9 km/h

[0.0(3.0) - 65.9 mph]

Odo Total Distance

0.0 - 9999.9 /

10000 - 99999 km [mile]

Clock

0:00 - 23:59

or 1:00 - 12:59

*1 With the computer installed on the bracket, press

on the three raised dots on the face of the

computer.

*2 If Tm DST exceeds approximately 27 hours or

exceeds 999.99 km, .E (Error) is displayed as

the average speed. Reset data.

Setting

change (by

pressing &

holding)

Current speed

0.0(4.0) - 105.9 km

[0.0(3.0) - 65.9 mph]

Changing the computer settings [menu screen]

If the MENU is pressed with the measuring screen displayed, the menu screen

appears. Press the when measurement has stopped and no signal isMODE

being received to change menu settings.

Starting/Stopping measurement

Measurements occur automatically when

the bicycle is in use. During

measurement, or flashes.

Switching computer function

Pressing MODE switches function, in

order, as shown on the left.

Resetting data

To reset measurement data, display any

data other than for and then press andDst-2

hold MODE. Pressing and holding MODE

with Dst-2 displayed resets Dst-2 only.

The total distance is never reset.

Power-saving function

If the computer has not received a signal

for 10 minutes, power-saving mode will

activate and only the cl ock will be

displayed. When the computer receives a

sensor signal again, the measuring screen

reappears. If two weeks inactivity elapses,’

power-saving mode will change to SLEEP

mode. Pressing the MODE in SLEEP mode

brings up the measuring screen.

Selected Mode

Wheel

selection

Wheel size

entry

Clock setting Total distance

manual entry

Speed unit

* After changing, be sure to press to register theMENU

setting.

* If the menu screen is not touched for a minute, the

Measuring screen reappears without data changes.

TOP

CR2032

Inner Seal

Cap

COIN

CR2032

Push!

Produkt Specifikationer

Mærke:	Cateye
Kategori:	Cykel computer
Model:	Strada CC-RD300W

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Strada CC-RD300W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel computer Cateye Manualer

Cateye Vectra Wireless CC-VT100W Manual

4 September 2024

Cateye CC-RD430DW Strada Manual

3 September 2024

Cateye Quick CC-RS100W Manual

1 September 2024

Cateye Padrone+ CC-PA110W Manual

1 September 2024

Cateye Padrone Digital CC-PA400B Manual

1 September 2024

Cateye CC-RD410DW Strada Manual

31 August 2024

Cateye CC-RD400DW Strada Manual

26 August 2024

Cateye OS 1.1. Manual

12 August 2024

Cateye Velo Wireless Manual

5 August 2024

Cateye CC-AT200W Adventure Manual

2 August 2024

Cykel computer Manualer

Nyeste Cykel computer Manualer

Lezyne Micro C Manual

30 December 2025

BBB BCP-35W Manual

12 Oktober 2024

Crivit HG01734A Manual

3 Oktober 2024

Sigma Pure GPS Manual

2 Oktober 2024

Bryton Rider 20 Manual

2 Oktober 2024

Sigma BC 1600 Manual

30 September 2024

Lezyne Mega XL GPS Manual

29 September 2024

Wahoo Elemnt Roam v2 Manual

23 September 2024

Trelock BB 4000i Manual

23 September 2024

Echowell Ui-20 Manual

23 September 2024