Cateye Velo 8 CC-VL810 Manual

Cateye Cykel computer Velo 8 CC-VL810

Læs gratis den danske manual til Cateye Velo 8 CC-VL810 (2 sider) i kategorien Cykel computer. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Cateye Velo 8 CC-VL810, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CATEYE VELO5

CATEYE VELO8

CYCLOCOMPUTER

Model CC-VL510/CC-VL810

ENG

U.S. Pat. Nos. 4642606, 5236759 and Pat. Pending

CCVL51/81-110930 066600560

INSTALLING THE UNIT

1 2 3

SET

(on Back)

VELO 8VELO 5

MODE

YES!

NO!

Click

6 7

SETTING

5 mm

Before using the computer, please thoroughly read this manual and keep it for future reference.

Caution

• Do not concentrate on the computer operations while riding. Always be sure to ride safety.

• Be sure to securely mount the magnet, sensor and bracket on your bicycle, and periodically check to

see if any parts have loosened.

• Used batteries are harmful if swallowed by mistake. They must be disposed in accordance with local

regulations.

• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.

• For cleaning of the main unit or accessories, use diluted neutral detergent on a soft cloth, and then wipe

it off with a dry cloth. Do not use paint thinner, benzine or alcohol since such chemicals may damage

the surface.

Package Contents

1 2 3 Bracket Wire Sensor

4 5 Magnet Nylon Ties (x 7)

IMPORTANT!

Correct positions of the sensor and the magnet:

When rotating the front wheel, the magnet's center must be aligned with the sensor's marking4 3

line.

The distance between the sensor and the magnet must be less than 5 mm.3 4

Name of Parts

Speed 0.0 (4.0) to 299.9 km/h [0.0 (3.0) to 185.0 mph]

Mode Symbol Indicates the mode currently selected.

(The corresponding value is indicated on the lower line.)

Pace Arrow* Indicates if the current speed is faster or slower than the average speed. (

Faster Slower)

Speed Scale

Sub Display (selected function)

Battery Case Cover

Contact

*The Pace Arrow feature is only available on the VELO8. Pace Arrows are not displayed on the VELO5.

Display function

• Tm* [Elapsed Time] 0:00'00" to 9:59'59"

• Dst [Trip Distance] 0.00 to 999.99 km [mile]

• Av* [Average Speed] 0.0 to 299.9 km/h [0.0 to 185.0 mph]

(Measurable up to 27 hrs or 999.99 km/h)

• Mx [Maximum Speed] 0.0 (4.0) to 299.9 km/h [0.0(3.0) to 185.0 mph]

• Cal* [Calorie Consumption] 0.0 to 9999.9 kcal (estimated from speed data)

• Odo [Total Distance] 0.0 to 9999.9 km [mile]

• [Clock] 0:00' to 23:59' [1:00'to 12:59']

* This feature is only available on the VELO8. No measurement is done on the VELO5.

Start/Stop of Measuring

The unit starts measuring automatically when you start pedaling, and stops measuring when your come

to a stop.

The upper display always shows the Current Speed.

Shift of Lower Display

Each time you press the MODE button, a different data value appears on the lower line.

Power Saving Function

If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving

Mode and displays the clock count only. To re turn to normal display, press the MODE button or start

your bicycle again to cancel the Power Saving function.

Data Reset

When a screen with the

Reset

mark in the OPERATION FLOW is displayed, continue pressing the

MODE button and the measured data will return to zero. However, the Odometer (total distance) and

Clock do not return to zero.

How to Set Clock

In the clock mode, press SET button on the back, and the display enters clock setting mode.

*If Km/h has been selected for speed scale, it becomes 24-hour clock.

If mph has been selected, it becomes 12-hour clock.

How to Change Tire Size

Display the Total Distance (Odo) and press the SET button to change the tire size. You can select a tire

size in two ways: Either select from among preset sizes

or enter the tire’s circumference directly in

increments of 1 cm. d

Maintenance

• If the contact of the unit or the bracket gets wet, dry it off with a cloth. If they become rusty, it will

cause speed detection error.

• If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with

water.

Troubleshooting

No display.

Has the battery in the main unit run down?

Replace it with a new one.

The main unit may still have a charge.

Put the battery in backwards to short the unit then install properly and do all clear operation.

Incorrect data appears.

Do all clear operation.

Current speed does not appear. (First, short-circuit the contact of the main unit a few times with a piece

of metal. If current speed appears, the main unit is working fine and the cause should be attributed to the

bracket or the sensor.)

Is the clearance between the sensor and the magnet too large?

Are the magnet's center and the sensor's marking line aligned?

Re-adjust the positions of the magnet and the sensor. (The clearance should be less than 5

mm.)

Is the cord broken?

Even if the outside of the cord looks normal, there could be damage.

Replace the bracket and sensor set with a new one.

Is there anything sticking on the contact of the main unit or the bracket?

Clean the contact with a cloth.

Current speed disappears when using in the rain.

Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not

apply standard grease, as it may cause damage to the bracket.

Replacing Battery

If the screen becomes dim, it is the time to replace the battery.

*Insert a new lithium battery (CR2032) with the (+) mark facing up.

After replacing the battery, perform the all-clear operation. Follow SETTING to select the measurement

unit & tire size and set the clock display to the current time.

Specification

Battery --------------------- Lithium Battery CR2032 x 1 (battery life: approx. 3 years)

(*The life of the factory-loaded battery might be shorter than this.)

Microcomputer ----------- 4-bit 1-chip (Crystal controlled oscillator)

Display --------------------- Liquid crystal display

Sensor --------------------- No-contact magnetic sensor

Tire Sizes ------------------ Tire sizes of 16, 18, 20, 22, 24, 26, 700C, and 27 inches, or tire peripheral

lengths from 100 to 299 cm (Initial value: 26 in.)

Working Temperature --- 0 ° °C – 40 C

Length of Wire ------------ 70 cm

Dimension/Weight ------- 2-1/16" x 1-1/2" x 45/64" (52.5 x 38 x 18 mm) / 0.95 oz (27 g)

* The specifications and design are subject to change without notice.

Produkt Specifikationer

Mærke:	Cateye
Kategori:	Cykel computer
Model:	Velo 8 CC-VL810

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Velo 8 CC-VL810 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel computer Cateye Manualer

Cateye Vectra Wireless CC-VT100W Manual

4 September 2024

Cateye CC-RD430DW Strada Manual

3 September 2024

Cateye Quick CC-RS100W Manual

1 September 2024

Cateye Padrone+ CC-PA110W Manual

1 September 2024

Cateye Padrone Digital CC-PA400B Manual

1 September 2024

Cateye CC-RD410DW Strada Manual

31 August 2024

Cateye CC-RD400DW Strada Manual

26 August 2024

Cateye OS 1.1. Manual

12 August 2024

Cateye Velo Wireless Manual

5 August 2024

Cateye CC-AT200W Adventure Manual

2 August 2024

Cykel computer Manualer

Nyeste Cykel computer Manualer

Lezyne Micro C Manual

30 December 2025

BBB BCP-35W Manual

12 Oktober 2024

Crivit HG01734A Manual

3 Oktober 2024

Sigma Pure GPS Manual

2 Oktober 2024

Bryton Rider 20 Manual

2 Oktober 2024

Sigma BC 1600 Manual

30 September 2024

Lezyne Mega XL GPS Manual

29 September 2024

Wahoo Elemnt Roam v2 Manual

23 September 2024

Trelock BB 4000i Manual

23 September 2024

Echowell Ui-20 Manual

23 September 2024