CaviLock CL200 Manual

CaviLock Ikke kategoriseret CL200

Læs gratis den danske manual til CaviLock CL200 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om CaviLock CL200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CL200

Magnetic

Installation

Instructions

for Passage or

Privacy Handle

PAGE

BEFORE YOU START:

The door must be installed and

adjusted square to the closing

jamb for the handle to close

properly onto the striker.

INSTRUCTIONS

1. Remove handle from packaging

This handle is temporarily screwed to an aluminium

frame using the same screws (6 in total) needed to

install it to your door. As you remove the handle from the

aluminium frame, take note of how it is ﬁtted as you will

be ﬁtting it to your door in the reverse order (diagram a).

2. Cut out door

Mark a horizontal line on the

face of the door where the

centre of the handle is to be

positioned (diagram b).

Align the centre line on the

aluminium frame with the

centre line on the door.

Trace around the inside of the

aluminium frame as shown.

Repeat on the other side of

the door.

Transfer top and bottom lines

across the front edge of the

door.

Cut out the door along the

marked lines.

4. Fit the handle

a) Screw the wedges into the

rebates in the door as shown

( ) using the 4 x ﬂat diagram d

head screws which were part

of the packaging.

Aluminium

frame

Transfer

across

front

edge

Mark

inner

edge of

template

Horizontal

line

Ø3mm (1/8”)

holes

35mm (1-3/8“)

deep

Drilling

template

3. Drill ﬁxing holes

Remove the plastic drilling

template from the back of the

aluminium packaging frame.

Place the template into the

rebate with the bosses facing

towards you ( ). diagram c

Line it up on the centre of the

door thickness.

Using a Ø3mm (1⁄8”) drill,

spot through all six holes.

Remove the template and

drill holes to depth of 35mm

(1-3/8”).

Wedges

Flat head

screws (4)

5mm gap (1/4”)

under head

DO NOT FULLY TIGHTEN THE

SCREWS.

The underside of the

screw heads should stop

approximately 5mm (1/4”)

above the top of the wedges.

This handle IS NOT handed.

Handing is determined at time of

ﬁtting by which way round the side

handles are ﬁtted to the door.

DO NOT throw away the packaging

until the handle is fully ﬁtted.

Go to page 3 (overleaf)

COMPONENTS

(Privacy Handle Shown)

Top plastic cap

Bottom plastic cap

Striker

screws (2)

Aluminium

frame

(cut out

template)

Drilling

template

Side

handle

Side

handle

Flat head

screws (4)

Face

plate

screws

(2)

Face

plate

Wedges

(2)

Snib button

(may vary)

Snib joining

Alignment

pins (2)

IMPORTANT:

A. The aluminium frame is used as a template to mark out

the door cut out.

B. The rectangular plastic moulding is used as a drilling

template.

C. The bottom packaging cap has the striker ﬁtted to it

(Privacy Handles). The snap out plastic moulding is used

to mark the striker position on the closing jamb and to

test that the lock functions correctly.

Remove the two face plate screws using a 3.5mm (9⁄64”) hex

screwdriver bit (supplied).

Pull the face plate out from between the side handles.

Remove the four remaining screws now visible after removal of

the face plate.

Alternate snib

joining pin

Hex screwdriver bit

Striker setting tool

CAVILOCK

CL200 Magnetic™ (O.D. 2017)

INSTALLATION INSTRUCTIONS.

61258/CL205ZA164 - 11.2017 © Cavity Sliders Ltd.

All copyright and other property in this document is reserved

by Cavity Sliders Limited. Details and speciﬁcations are

subject to change without notice. Whilst all care is taken

to ensure the accuracy of all information, no responsibility

will be accepted for any errors or omissions. ® CS FOR

DOORS, CS CAVITY SLIDERS and CAVILOCK are Registered

Trademarks. Patents pending.

Striker

setting

tool

Striker

screws

Striker

Slotted

hole

cavitysliders.com.au

cavitysliders.com

Mark on

closing

jamb

Cavity Sliders Ltd

Auckland Head Ofﬁce

5 - 7 Rakino Way

Mt Wellington

Auckland, NZ

WARNING: THIS BOX MAY CONTAIN A STRONG MAGNET

IRON FILINGS - Magnets will attract shavings from iron or ferrous metals

which may be hard to remove. Keep the face plate a safe distance away from

these materials.

DANGER FOR CHILDREN - Magnets may cause serious injury if swallowed.

Keep out of reach of children.

CRUSHING, BLISTERS AND CUTS - Fingers may become caught between

magnets resulting in crushing, blisters or cuts.

BREAKING OR CHIPPING - It is possible that magnets could chip or shatter

on contact, resulting in chips ﬂying off at high speed into someone’s eye.

Chips can also be very sharp - treat them as you would broken glass.

MAGNETICALLY SENSITIVE ITEMS - Keep a safe distance between the

magnet and all objects that can be damaged by magnetism (e.g. mechanical

watches, pacemakers, cell phones etc.).

DISPOSAL - Magnets should be disposed of carefully and in accordance with

your local regulations.

6. Fit the striker (Privacy Handles Only)

You will ﬁnd the steel striker and ﬁxing screws pushed onto

a snap out plastic moulding in the bottom packaging cap

( ). This striker setting tool serves two purposes:diagram a

a) Test or demo the

locking function.

Insert the striker setting tool

as shown ( ) into the diagram i

rectangular ﬁnger pull hole in

the face plate of the handle.

Hold the template in place

and push down on the snib

button.

b)Mark ﬁxing screw positions

on the closing jamb.

With the striker setting tool

still ﬁtted into the face plate,

close the door against the

timber closing jamb so that

the plastic plate makes a

small mark on the jamb

(diagram j).

Use this mark to ﬁt the

bottom striker screw through

the centre of the slotted hole.

Close and latch the door to

check the alignment.

Adjust if necessary before

ﬁtting the top striker screw.

5. Fit the face plate

With both side handles fully

tightened you can now ﬁt the

face plate.

The open fork of the plastic

slider must slide over

the steel snib button pin

when ﬁtting the face plate

( ) diagram h .

Lift up the snib button so that

the joining pin lines up.

Test snib action before

fastening the two face plate

screws.

Plastic

slider

Snib

joining

Face

plate

Privacy Handles Only

Check that the correct length snib button joining pin is

ﬁtted into the back of the snib button. See for Table 1

correct pin lengths. Swap with the pin in the top

packaging cap if required.

Door Thickness Alignment

Pin Length

Snib Joining

Pin Length

33 - 36 1-5/16” to 1-7/16” 31.5 1-1/4” 27.5 1-1/8”mm mm mm

37 - 40 1-1/2” to 1-9/16” 31.5 1-1/4” 31.5 1-1/4”mm mm mm

40 - 43 1-5/8” to 1-11/16” 38.5 1-1/2” 34.5 1-3/8”mm mm mm

44 - 46 1-3/4” to 1-13/16” 38.5 1-1/2” 38.5 1-1/2”mm mm mm

4. Fit the handle

b) Slide one of the side

handles under the two screw

heads as shown ( ) diagram e

checking that you have the

correct handing.

While pressing the side

handle ﬁrmly against the side

of the door fully tighten the

front screws.

Privacy

handle

shown

Privacy

handle

shown

Snib

joining

Alignment

c) Repeat the process with the

other side handle, taking care

to line up the alignment pins

with the two holes in the side

handles and the third hole in

the snib button (only applies

to privacy handles) (diagram f).

Bi-Parting Handles Only

Before ﬁtting the face plate

you will need to ensure the

striker has been ﬁtted.

Use the two screws and

washers supplied (diagram g).

Bi-Parting

face plate

Screws

& washers

Striker

PAGE

27.5

34.5

31.5

38.5

Pin Lengths

Table 1 - Pin Lengths

csfordoors.co.nz

Produkt Specifikationer

Mærke:	CaviLock
Kategori:	Ikke kategoriseret
Model:	CL200

Har du brug for hjælp?

Hvis du har brug for hjælp til CaviLock CL200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret CaviLock Manualer

CaviLock CL200 Manual

1 Oktober 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Varta Wireless Charger Multi 57906 Manual

13 September 2025

IFM DV1203 Manual

13 September 2025

SolarEdge SE90K-SYNERGY-SET Manual

13 September 2025

TriStar PD-3817E Manual

13 September 2025

IFM DV1200 Manual

13 September 2025

Ibm System Storage N3220 Manual

13 September 2025

IFM SU9030 Manual

13 September 2025

IFM O2U554 Manual

13 September 2025

Speco Technologies HTi70TM Manual

13 September 2025

QSC RMXa Manual

13 September 2025