CDN SD2210X Manual

CDN Køkkenvægt SD2210X

Læs gratis den danske manual til CDN SD2210X (4 sider) i kategorien Køkkenvægt. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om CDN SD2210X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Features

• NSF® Certied

• Submersible (IP67: protected from water up to 3 feet

for 30 minutes, completely protected against dust)

• Programmable

• Tare function

• Backlit display

• Field calibration

• Low/high limit alerts

• Selectable units

• Stability indication

• Overload indication

• Battery status indication

• Stainless steel housing

• Removable stainless steel platform

• On/off button

• Auto-off after 2 minutes, programmable to 5 minutes;

disabled when AC adapter used

• Platform Size: 7.2 W x 6.7 L (in)/18.2 W x 17.0 L (cm)

• Resolution: 0 lb:0.1 oz, 0 lb:1/8 oz, 0.005 lb,

0.05 oz, 1/8 oz, 1 g

• Rechargeable battery: 4.8V 1800mAH (built-in)

• Power Adapter: 100-240VAC 50/60Hz input, 9V DC

(1000mA) output (included)

Note: Clean the scale before each use.

Note: In the following instructions, names of the

control buttons are shown in CAPS. Function

information that appears on the display is shown in

BOLD CAPS.

Power Adapter

Before using the external power adapter, make sure

that the printed voltage complies with the local

voltage.

Note: Use only an original CDN power adapter (AD-AC1110).

The use of other adapter is subject to approval by CDN.

1. Insert the adapter plug into the jack in the rear

of the scale.

2. To turn the scale on, press the POWER button

( ) as described in Section A: On/Off. The scale will

remain on until turned off.

Note: When the power adapter is plugged in, the auto-off

feature is disabled.

Charging the Battery

The icon ( ) and appear on LOW BATTERY bAtt

the display when battery status is low and needs

to be charged. The icon ( ) ashes LOW BATTERY

continuously while charging. The battery is built-in and

does not need to be replaced.

1. Insert the adapter plug into the jack on the back

of the scale. Allow the scale to charge for

5 hours. The scale will then operate continuously for

approximately 14 hours

Operating Instructions

Place the scale gently on a hard and at surface

and make sure it is steady before use to obtain

accurate measurements.

A. On/Off

A. Press the POWER button ( ) to turn on.

The display ashes all segments and then

returns to zero.

B. The STABILITY icon ( ) appears in the lower left

corner of the display when the weight is stable.

C. Press the POWER button ( ) to turn off.

B. Auto Off

The scale automatically turns off after 2 minutes of

inactivity.

Note: Auto-off is disabled when the AC adapter is used.

Model: SD2210X

ProAccurate

Submersible Scale

22 pounds/10 kilograms/352 ounces

by pounds:ounces, ounces, fractional ounces and grams

C. Backlit Display

Press and hold the UNIT button for 3 seconds

to turn the backlit display on and off.

D. Unit Selection

Press the UNIT button to select the desired unit. The

display cycles through g, , , lb:oz lb:/oz lb, oz, and /oz.

E. Tare

The tare function resets the scale display to zero

in order to measure only the weight of an item. It is

frequently used to subtract the weight of containers.

1. When the scale is on, place a container on

the platform.

2. Press the TARE button to reset the display

to zero.

3. Place the item into the container or directly on

the scale platform. The weight of only the last

item added will appear on the display.

4. Continue to repeat steps and 2. 3. to measure

the respective weights of additional items.

5. To clear the tare, remove all items from the

platform and press the TARE button. The display

is reset to zero.

F. Low/High Limit Alerts

The scale may be set to alert you when an item’s

weight is under or over a set limit.

1. Press and hold the TARE button for 3 seconds.

The scale beeps as and the zero weight LOW

appears on the display.

2. Place a weight equal to the low weight limit on

the platform and press the SET button. A beep

indicates that the low limit is set.

3. HIGH appears on the display. Add weight to the

platform until the weight is equal to desired

high weight limit. Press the SET button. A beep

indicates that the high limit is set.

4. Remove all items from the platform.

5. An alert will now sound if an item placed on

platform is over or under the set limits. LOW

or appears on the left side of the display HIGH

when these conditions exist.

6. To clear the Low/High limits, press both SET and

TARE buttons simultaneously.

G. Field Calibration

1. When scale is off, press and hold POWER button

( ) until the scale turns on. When all segments

are on, release the POWER button ( )

and press the UNIT button 3 times within one

second. The display shows , then , 11111 55555

and then the version number and checksum

appear before resetting to zero.

2. Making sure there is no load on the platform,

press the SET button to save the zero value.

3. Put a 10 kg (or two 5 kg) calibration weight on

the platform.

4. Press the SET button again to start the

auto-calibration. The scale shows 5000 g

and then before automatically turning off. CAL

The calibration is complete.

H. Battery Status

Battery status is low and needs Low Battery:

to be charged. See on Charging the Battery

page 1.

I. Error Messages

oL indicates an overload when the item being

measured exceeds the capacity of the scale.

Immediately remove the overweight item to avoid

causing permanent damage to your scale.

J. Programmable Modes

The scale has been pre-congured at the factory

and should not require conguration for use in most

applications. In the event that the factory settings

do not meet the requirements of your application,

the following describes the steps

to congure the scale.

1. Units

The scale has been pre-congured at the factory

for six units of measure. In the event that these

do not meet the requirements of your application,

the following describes the steps

to limit the number of unit choices available. The

sequence of units is , , , , lb:oz lb:/oz lb oz

/oz and .g

a. Press the POWER button ( ) to turn on.

b. Press and hold the SET button for 3 seconds.

When appears on the display, release the SEt

SET button to enter the conguration mode.

UNIT appears on the display.

c. With UNIT appearing on the display, press the

SET button to select lb/OZ (pounds/ounce)

units (11 lb @ 0.1 oz). Both the unit and its

status appear on the display.

d. Press the UNIT button to toggle between

ON (enabled) and OFF (disabled).

e. Press the SET button to conrm the status

and to select the next unit in the sequence.

f. Repeat steps d. and e. for each respective

unit. Upon conrming the status for , g

UNIT appears on the display.

g. Press the UNIT button three times.

END appears on the display.

h. Press the SET button to save the settings and

return to weighing mode.

2. Auto Off

The scale has been pre-congured at the factory

to automatically turn off after 120 seconds

(2 minutes) of inactivity. In the event that your

application requires longer shut-off times or none

at all, the following describes the steps

to congure this feature.

Produkt Specifikationer

Mærke:	CDN
Kategori:	Køkkenvægt
Model:	SD2210X

Har du brug for hjælp?

Hvis du har brug for hjælp til CDN SD2210X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køkkenvægt CDN Manualer

18 August 2024

18 August 2024

18 August 2024

18 August 2024

Køkkenvægt Manualer

Nyeste Køkkenvægt Manualer

Kern PES 6200-2M Manual

26 September 2025

Kern PBJ 6200-2M Manual

26 September 2025

Kern EW 420-3NM Manual

26 September 2025

Kern PBS 620-3M Manual

26 September 2025

Kern PBJ 4200-2M Manual

26 September 2025

American Weigh Scales AC-100 Manual

24 September 2025

Livoo PET109 Manual

23 September 2025

Vogue CD564 Manual

23 September 2025

Eta Mari 5770 90000 Manual

21 September 2025

Eta Lori 2777 90000 Manual

21 September 2025