CDN SDR220 Manual

CDN Vægten SDR220

Læs gratis den danske manual til CDN SDR220 (4 sider) i kategorien Vægten. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 19 anmeldelser. Har du et spørgsmål om CDN SDR220, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Features
• Programmable preset unit
• Tare function
• Extendable display
• Selectable units
• Overload indication
• Battery status indication
• On & off buttons
• Auto-off after 4 minutes; disabled when the power
• Platform Size: 12.06 L x 11 W x 1.30 H (in)/
30.64 L x 27.94 W x 3.30 H (cm)
• Extendable Display: 4.92 L x 4.52 W x 1.96 H (in)/
12.50 L x 11.50 W x 5.00 H (cm)
• Resolution: 2 oz, 50 g
• Power Adapter: 100 mA-250 mA 50/60 Hz input,
9V DC (500mA) output (included)
• 9V IEC 6LR61 alkaline battery (included)
Note: Clean the scale before each use.
Important: DO NOT IMMERSE IN LIQUID.
Note: In the following instructions, names of the
control buttons are shown in CAPS. Function
information that appears on the display is shown in
BOLD CAPS.
Remove Stabilizing Screw
Before using the scale, remove the red stabilizing
screw on the bottom of the scale by turning it
counterclockwise. Before transporting the scale,
replace the stabilizing screw back in by turning it
clockwise into the screw hole.
Battery Installation
Replace battery when LCD becomes dim. Lo appears
on the display for 2 seconds before turning off when
the batteries need to be replaced.
1. Power off the unit before installing the battery.
2. Remove battery cover on the bottom of the display
by pressing the latch toward the battery cover and
lifting up.
3. Install one 9V IEC 6LR61 alkaline battery observing
polarity shown in compartment.
4. Replace the battery cover until it clicks shut.
Power Adapter
Before using the external power adapter, make sure
that the printed voltage complies with the local
voltage.
Note: Use only an original CDN power adapter (AD-AC3302).
The use of other adapter is subject to approval by CDN.
1. Insert the adapter plug into the jack in the rear
of the display.
2. To turn the scale on, press the ON/TARE button as
described in Section A: On/Off. The scale will remain
on until turned off.
Note: When the power adapter is plugged in, the auto-off
feature is disabled.
Model: SDR220
Digital
Shipping & Receiving Scale
220 pounds/100 kilograms
by pounds:ounces and kilograms
Operating Instructions
Place the scale gently on a hard and at surface and
make sure it is steady before use to obtain accurate
measurements.
A. On/Off
1. Press the ON/TARE button to turn on. The display
ashes ---- and then returns to zero.
The + symbol indicates positive measurements.
2. Press the OFF button to turn off.
B. Auto-Off
The scale automatically turns off after 4 minutes of
inactivity when the AC adapter is not plugged in.
Note: Auto-off is disabled when the AC adapter is used.
C. Unit Selection
1. Press the UNIT button to select the desired unit.
The display cycles an arrow through , and kg lb:oz
preset.
D. Weighing Mode
1. Press the ON/TARE button to turn on. The display
ashes ---- and then returns to zero.
2. Place an item on the scale platform.
The weight of the item appears on the display
within 1 second after the item is stable.
3. Press the OFF button to turn off.
Note: The scale automatically turns off after 4 minutes
of inactivity when the AC adapter is not plugged in.
E. Tare
The tare function resets the scale display to zero
in order to measure only the weight of an item. It is
frequently used to subtract the weight of containers.
1. When the scale is on, place a container on
the platform.
2. Press the ON/TARE button to reset the display to
zero. The display ashes and then returns t
to zero.
3. Place the item into the container or directly on
the scale platform. The weight of only the last
item added will appear on the display.
4. Continue to repeat steps and 2. 3. to measure
the respective weights of additional items.
5. To clear the tare, remove all items from the
platform and press the ON/TARE button.
The display resets to zero.
F. Preset Mode
The preset unit is a programmable unit that serves
as a point of comparison for subsequent weights
that need to match the preset unit or a percentage
thereof. It is frequently used in packing and shipping
applications.
1. Press the UNIT button to select preset.
a. If it is the rst time being used since
a battery was installed, appears on –
the display.
b. If the preset unit was saved before, 0.00 appears
on the display.
2. Place the item with the reference weight on the
scale platform.
Note: The minimum weight for the preset unit is 5kg.
E appears on the display when the item with the
reference weight is below the minimum weight. Please
place an item with the weight over the minimum weight
to continue.
3. Press and hold the ON/TARE button until the
arrow blinks.
4. Immediately press the ON/TARE button again to
conrm the preset unit. The display shows . 1.00
The preset unit has been set.
Note: This preset unit will be held in memory until
changed or the removal of the battery.
5. To change the preset unit, repeat steps 1.
through 4.
6. To compare other items, place an item on the
scale platform. The percentage as compared to
the preset unit appears on the display.
For example: appears on the display when an 0.85
item that weighs 85% of the total preset unit weight
is weighed. 1.30 appears on the display when an item
that weighs 130% of the total preset unit weight
is weighed.
G. Field Calibration
1. Press and hold the ON/TARE and OFF buttons
simultaneously, while installing the battery or
plugging in the AC adapter, until all segments are
displayed.
2. Release both buttons. The display returns to zero.
3. Press the OFF button. The display shows .50.00
4. Place a 50 kg calibration weight on the scale.
The scale performs internal calculations and then
the display shows 100.00.
5. Place a 100 kg calibration weight on the scale.
The scale performs internal calculations.
6. PASS appears on the display if the calibration is
successful. Then the scale automatically turns
off. The scale has been calibrated and is ready
for use.
7. FAIL appears on the display if the calibration
is not successful. Then the scale automatically
turns off. Return to step and try the calibration 1.
again. calibration continually fails, please contact
CDN for further assistance.

Produkt Specifikationer

Mærke: CDN
Kategori: Vægten
Model: SDR220

Har du brug for hjælp?

Hvis du har brug for hjælp til CDN SDR220 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Vægten CDN Manualer

CDN

CDN SDR220 Manual

18 August 2024

Vægten Manualer

Nyeste Vægten Manualer

Kern

Kern PCD 300-3 Manual

1 April 2025
Kern

Kern FCE 3K-3A Manual

30 Marts 2025
Kern

Kern TEFS 500-2-A Manual

30 Marts 2025
Kern

Kern MPL 200K-1P Manual

30 Marts 2025
Kern

Kern TGC 500-1S05 Manual

29 Marts 2025
PCE Instruments

PCE Instruments PCE-BSK 5100 Manual

28 Marts 2025
PCE Instruments

PCE Instruments PCE-PB 150N Manual

14 Marts 2025
PCE Instruments

PCE Instruments PCE-BSH 10000 Manual

14 Marts 2025
PCE Instruments

PCE Instruments PCE-MA 202 Manual

14 Marts 2025
PCE Instruments

PCE Instruments PCE-PCS 6 Manual

14 Marts 2025