Celestron Wedge Manual

Celestron Ikke kategoriseret Wedge

Læs gratis den danske manual til Celestron Wedge (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Celestron Wedge, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

P HD Wro eDge

MODEL #93664

ENGLISH

1. Loosen the two latitude locking screws on both sides of the

wedge (Figure 2).

2. Push the tilt plate all the way forward as far as it will go, and

hand tighten the locking screws to hold the tilt plate in place.

3. Thread back the latitude adjustment knob so that the threaded

rod does not interfere with the orange support rod.

4. Remove the three top screws from each of the L-brackets on

the bottom of the tilt plate. Do not remove the bottom screws.

5. Place one end of the swivel block into one of the top holes

on the inside of the L-bracket. It may be necessary to loosen

the bottom screws and rotate the L-bracket enough to ﬁt the

swivel block between the brackets.

Note: The top hole position can be used for most latitudes.

At higher latitudes the upper hole will give more stability.

However at lower latitudes the middle or lower hole

position will give more range of motion if needed.

6. Once one side of the swivel block is in place, reattach the

screws to hold the L-bracket to the tilt plate.

7. Attach the remaining L-bracket to the bottom of the tilt plate

making sure the other end of the swivel block ﬁts inside the

corresponding hole on the bracket. Tighten both brackets.

ADjusting tHe WeDge for Your LAtituDe

Your wedge can be conﬁgured in two different ways; for latitude

range of 0° – 50°, or a latitude range of 40° - 90°. If you are at

a latitude between 40° - 50° either conﬁguration should work

for you. The wedge comes pre-assembled in the 40° - 90°

conﬁguration. However, if you are located at a latitude of 40° or

below you will need to adjust the latitude plates on the side of

the wedge. To adjust the latitude plates:

1. Loosen the pivot bolt on one of the side latitude plates.

2. Remove the three countersunk bolts holding the latitude plate

to the wedge.

3. Rotate the latitude plate downward so that the three holes line

up with the lower set of holes.

4. Replace the three bolts to attach the plates to the wedge

and tighten the pivot bolt.

5. Repeat the steps above for the second latitude plate.

6. Reattach the latitude locking screws and hand tighten.

Assembling the Wedge

Your Celestron telescope has a motor drive built into the base

allowing it to track the stars as they move across the sky from

east to west. However, for this drive to be useful, (particularly

for astrophotography) the telescope’s axis of rotation should be

made parallel to the Earth’s axis. The Pro HD Wedge allows you

to tilt the telescope’s axis of rotation (polar or R.A. axis) so that

the telescope can track the stars as they move in an arc around

the celestial pole. When this is accomplished, the sky’s motion

can be cancelled out simply by having the telescope rotate at

the same rate as the rotation of the Earth, but in the opposite

direction. This process is known as polar alignment.

Your wedge comes pre-assembled out of the box. However you

will need to attach the latitude adjustment rod and may need to

adjust the side latitude plate depending on your latitude.

F 1igure

Tilt Plate

L-Bracket

Swivel

Block

F 2igure

Pivot Bolt

Latitude

Locking

Screw

Latitude

Scale

Latitude Adjustment Knob

Latitude

Plate

Produkt Specifikationer

Mærke:	Celestron
Kategori:	Ikke kategoriseret
Model:	Wedge
Type:	Monteringsplade til teleskop
Vægt:	6803 g
Produktfarve:	Sort
Antal:	1
Kapabilitet:	NexStar Evolution 6/8/9.25, NexStar SE 6/8