Chef's Choice Manual 490 Manual


Læs gratis den danske manual til Chef's Choice Manual 490 (12 sider) i kategorien Knivsliber. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Chef's Choice Manual 490, eller vil du spørge andre brugere om produktet?

Side 1/12
MOdel 490 instructiOns
Manual Scissor Sharpener
Read these instructions before use.
It is essential that you follow these
instructions to achieve optimum results.
© 2013 EdgeCraft Corp.
cHeFscHOice ® MAnuAl scissOr sHArPener
The ChefsChoice
® Manual Scissor Sharpener Model 490 is designed to sharpen scis-
sors to professional standards, simply and easily. It can put an exceptionally sharp
edge on your kitchen, household, sewing, and arts and crafts scissors. There are sev-
eral distinctly different types of scissors, consequently, it is important to read this entire
booklet to optimize your sharpening results.
The Chef’sChoice® Model 490 Manual Scissor Sharpener owes much of its uniqueness
to its precision Angle Guides, designed to position the scissor blade securely at a pre-
cise angle against the diamond abrasive plates. Before sharpening your first scissors it
is important to read the following instructions carefully.
iMPOrtAnt inFOrMAtiOn
1. WARNING: EVEN THOUGH ALL SCISSORS MAY APPEAR TO BE SIMILAR, THERE ARE
MAJOR DIFFERENCES AMONG THEM THAT MUST BE UNDERSTOOD BEFORE YOU
USE THIS SHARPENER. THE MODEL 490 WILL SHARPEN MOST, BUT NOT ALL, TYPES
OF SCISSORS. DO NOT ATTEMPT TO SHARPEN HAIR STYLING SCISSORS, PINKING
SHEARS, MANICURE SCISSORS, SERRATED BLADES, TIN SNIPS, OR SCISSORS MORE
THAN 10 IN LENGTH.
The ChefsChoice® Model 490 Scissor Sharpener will sharpen most other blades, includ-
ing knife-edge scissors, as described below. It is essential, however that you follow the
instructions to optimize your results.
2. It is not entirely obvious that the two blades on some scissors can be different. When you
cut with scissors, one blade the anvil blade, is designed to be below the material and the
other blade called, the cutter blade, is above the material. See Figures 1 and 2. Commonly
the blade on top of the material, the cutter blade, does most of the cutting. Referring to the
Figures 1 and 2, note that the cutter blade usually has the oblong finger-hold and a more
rounded tip. The anvil blade has a more pointed tip and a round finger hold.
3. It is very important to be able to identify the special knife-edge type scissors. They
have a cutter blade that is factory sharpened at a very small angle to form a knife-like
edge that is extremely sharp. THE KNIFE-EDGE CUTTER BLADE MUST BE SHARPENED
ONLY WITH THE WHITE KNIFE-EDGE ANGLE GUIDE SUPPLIED WITH EACH SHARP-
ENER. With this type scissor, the knife-edge cutter blade does virtually all the cutting.
Commonly only the cutter blade of this
type scissor has the knife edge. When
that is the case and you can properly
identify and sharpen that blade, sharpen-
ing the other (anvil). Only the knife-edge
scissor blade should be sharpened by
the special procedure on page 7. If you
elect to sharpen the anvil blade, use
the sharpening procedure for standard
scissors described in page 5. Do not
confuse these blades. If you have any
doubt about whether you have this type
of scissors, ask your nearest fabric or Figure 1. Typical right-handed scissors.
2


Produkt Specifikationer

Mærke: Chef's Choice
Kategori: Knivsliber
Model: Manual 490

Har du brug for hjælp?

Hvis du har brug for hjælp til Chef's Choice Manual 490 stil et spørgsmål nedenfor, og andre brugere vil svare dig