Citizen CAL F100 Manual
Læs gratis den danske manual til Citizen CAL F100 (3 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Citizen CAL F100, eller vil du spørge andre brugere om produktet?
Side 1/3
りゅうずの位置
F100 User's Guide
Component identication
Receiving the satellite time signal
To see details of charging time, specications, and operations, refer to the instruction manual:
Hour hand
Indication Reception result
OK e reception succeeded.
e time and calender have been corrected.
NO
e reception failed. e time and calendar was not
corrected and the time indication returns to the status
before the reception.
Indication Reception result
OK e reception succeeded.
e time and calender are corrected.
NO
e reception failed. e time and calendar was not
corrected and the time indication returns to the status
before the reception.
Setting Meaning
SMT ON Summer time is indicated.
SMT OFF e standard time is indicated.
Place name/
time zone
Second hand
Date
indication
Minute hand
Crown
ButtonⒶ
ButtonⒷ
RX : Reception-
in-progress
indication
OK/NO : Reception
result
indication
is watch is solar-powered. Expose the dial to light and use it suciently charged.
Outdoor signal reception is recommended for receiving satellite time signal.
1. Push the crown in to position 0.
2. Press and hold the lower right button Ⓐ until the second
hand points to "RX".
e previous reception result is rst indicated and signal reception starts.
Aer nishing reception, the second hand indicates the reception result
for 2 seconds and returns to normal movement.
• Actual appearance may dier from the illustration above.
Reception to adjust the time and calendar when the leap second has been
updated.
1. Push the crown in to position 0.
2. Press and hold the lower right button Ⓐ for 7 seconds.
Time reception starts aer the second hand points “RX” once and turns
fully around to point “RX” again.
1. Push the crown in to position 0.
2. Press and release the lower right button Ⓐ.
e previous reception result is indicated.
3. Press and release the button Ⓐ to nish checking.
Manual reception 1 (time required: 3 to 20 seconds)
Manual reception 2 (21 to 13 seconds)
Checking the previous reception result of the satellite signal
F100 instruction manual
Using the world time
Switching summer time and standard time
1. Pull the crown out to position 1.
2. Press and release the lower right button Ⓐ.
3. Push the crown in to position 0 to nish the procedure.
• Each time you press the button, ON and OFF changes alternately.
1. Pull the crown out to position 1.
e second hand indicates the current time zone and
the function hand indicates the summer time setting.
2. Rotate the crown to choose a time zone.
Time indication changes.
• See also "How to read indication of the world time setting" and "Table of
time zones and representative places".
3. Push the crown in to position 0 to nish the procedure.
e function hand returns to day indication.
e watch has 40 time zone markers with
several representative area names. A time zone
is set by pointing the second hand at one of the
markers.
On the illustration, the second hand points to
28 seconds and time zone setting is “+11.5”.
• Time zones are represented by osets from
UTC (Coordinated Universal Time).
Setting the world time
How to read indication of the world time setting
Table of time zones and representative places
Function hand
• Day indication
• Power reserve
level
(in ve levels)
• Summer time
setting
(ON/OFF)
0 1 2
Crown’s position
Time zone marker
Representative
area
Second
hand
Time
zone
Second
hand
Area
name
Representative
area
0 0 sec. LON London
+1 2 sec. PAR Paris
+2 4 sec. ATH Athens
+3 6 sec. RUH Riyadh
+3.5 7 sec. — Tehran
+4 8 sec. DXB Dubai
+4.5 9 sec. — Kabul
+5 10 sec. KHI K arachi
+5.5 12 sec. DEL Delhi
+5.75 13 sec. — Kathmandu
+6 14 sec. DAC Dha ka
+6.5 15 sec. — Ya ngon
+7 16 sec. BKK Bangkok
+8 18 sec. BJS(HKG) Beijing/Hong Kong
+8.75 20 sec. — Eucla
+9 21 sec. TYO Tokyo
+9.5 23 sec. ADL Adelaide
+10 25 sec. SYD Sydney
+10.5 26 sec. — Lord Howe Island
+11 27 sec. NOU Noumea
+11.5 28 sec. — Norfolk Island
Time
zone
Second
hand
Area
name
Representative
area
+12 29 sec. AKL Auckland
+12.75 31 sec. — Chatham Islands
+13 32 sec. TBU Nuku’alofa
+14 34 sec. — Kiritimati
-12 36 sec. — Baker Island
-11 38 sec. MDY Midway
-10 40 sec. HNL Honolulu
-9.5 41 sec. — Marquesas Islands
-9 42 sec. ANC Anchorage
-8 44 sec. LAX Los Angeles
-7 46 sec. DEN Denver
-6 48 sec. CHI Chicago
-5 50 sec. NYC New York
-4.5 51 sec. — Caracas
-4 52 sec. SCL Santiago
-3.5 53 sec. — St. John’s
-3 54 sec. Rio de JaneiroRIO
-2 56 sec. FEN Fernando de
Noronha
-1 58 sec. PDL Azores
Continued on the next page
Setting leap second
When the leap second setting is
“-35 seconds”
When the leap second setting is
“-65 seconds”
e hands point to “0 minute 35
seconds”.
e hands point to “1 minute 5
seconds”.
3. Press and release the upper right button Ⓑ to nish
checking.
Correcting the reference position
1. Push the crown in to position 0.
2. Press and hold the upper right button Ⓑ for 7 seconds.
3. Pull the crown out to position 2.
4. Press and release the lower right button Ⓐ repeatedly
to change hand/indication to be corrected.
• Each time you press the button
Ⓐ, the target changes as follows.
Date/day → hour hand → minute hand → second hand → (back to the top)
5. Rotate the crown to adjust the hand/indication.
• When you rotate the crown quickly a few times, the hand/indication will
move continuously.
• To stop the rapid movement, rotate the crown in either direction.
6. Push the crown in to position 0.
7. Press and release the button Ⓑ to nish checking.
F100 User's Guide
Indication of power generation amount in level
e level of power generation amount means power being generated by the solar cell
represented in 0 to 6 levels.
1. Pull the crown out to position 2.
2. Press and release the upper right button Ⓑ.
Using the “0:00:00” position as the starting point, the minute and second
hands indicate the leap second setting.
Turn the crown to adjust the setting if the leap second is not correct.
3. Push the crown in to position 0
to nish the procedure.
Checking the reference position
1. Push the crown in to
position 0.
2. Press and hold the
upper right button Ⓑ
for 7 seconds.
Correct reference positions:
• All hands : 12 o’clock position
• Date indication:midway
between 31 and 1
• Day : S (Sunday)
3. Press and release the
upper right button Ⓑ
to nish checking.
S
SMT
ON
OFF
F
T
W
T
M
S
Resetting the watch — All Reset
1. Pull the crown out to position 2.
2. Press and hold buttons Ⓐ and Ⓑ at the same time for
3 seconds or more and release them.
As you release the buttons, the hands move slightly to indicate that reset
completed.
Aer All Reset, adjust the reference position. Execute world time setting and
receive satellite signal manually to adjust the time and calendar aer that.
After All Reset
Adjusting the time and calendar manually
1. Pull the crown out to position 1.
2. Press and hold the upper right button Ⓑ until the
second hand points to 30 seconds.
3. Pull the crown out to position 2.
e hands point to 0 second.
4. Press and release the lower right button Ⓐ repeatedly
to change the hand/indication to be corrected.
• Each time you press the button Ⓐ, the target changes as follows.
Minute hand → hour hand → date → year/month → day → (back to the top)
5. Rotate the crown to adjust the hand/indication.
• Date indication changes to the next as the function hand rotates 5 times.
• When you rotate the crown quickly a few times, the hand/indication will
move continuously.
• To stop the rapid movement, rotate the crown in either direction.
6. Push the crown in to position 0 in accordance with a
reliable time source to nish the procedure.
Set the year and month with the position of the second hand.
“Month” corresponds to one of the
12 zones shown in the gure below.
Each number means month.
“Year” corresponds to the years
since leap year and is indicated with
markers in the zone of each month.
Month and year indications
7
12
1
2
3
4
5
6
7
8
9
10
11
7
Years since leap year:
0 (Leap year)
0
Years since leap year: 1
1
Years since leap year: 2
2
Years since leap year: 3
3
Checking the power reserve and power
generation amount
1. Push the crown in to position 0.
2. Press and release the upper right button Ⓑ.
e power reserve and power generation amount at the moment of
pressing the button
Ⓑ are indicated in levels.
Level
43210
Power
reserve
level
scale
S
SMT
ON
OFF
F
T
W
T
M
S
S
SMT
ON
OFF
F
T
W
T
M
S
S
SMT
ON
OFF
F
T
W
T
M
S
S
SMT
ON
OFF
F
T
W
T
M
S
S
SMT
ON
OFF
F
T
W
T
M
S
Duration
(approx.) 24 - 20
months 20 - 14
months 14 - 5 months 5 months -
5 days 5 days or
shorter
Meaning
Power
reserve is
sufficient. Power reserve is OK.
Power
reserve is
getting low.
Insufficient
charge
warning has
started.
OK for normal use Charge immediately.
Indication of power reserve in level
Level
Meaning
Indication
Sufficient power
generation for
charging.
Charge in a brighter location where the
level of power generation amount reaches
“5” or “6”.
Produkt Specifikationer
| Mærke: | Citizen |
| Kategori: | Ur |
| Model: | CAL F100 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Citizen CAL F100 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ur Citizen Manualer
28 Juli 2025
28 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
27 Juli 2025
Ur Manualer
- Calypso
- PAUL HEWITT
- Julie Julsen
- Timer
- Antelope Audio
- Ice Watch
- Jacques Lemans
- La Crosse
- Casio
- Zuiver
- Polar
- Tudor
- Rodania
- Skmei
Nyeste Ur Manualer
13 August 2025
13 August 2025
13 August 2025
13 August 2025
13 August 2025
13 August 2025
12 August 2025
12 August 2025
12 August 2025
7 August 2025