Cotek AE 1500-24 Manual

Cotek Ikke kategoriseret AE 1500-24

Læs gratis den danske manual til Cotek AE 1500-24 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Cotek AE 1500-24, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

MODEL

Output

DC Voltage Range

Rated Current

Current Range

Rated Power

Ripple & Noise (Max.)

Voltage Adj. Range

Voltage Tolerance

Line Regulation

Load Regulation

Setup, Rise Time

Hold Up Time (Typ.)

Input

Voltage Range

Frequency Range

Efficiency (Typ.)

AC Current (Typ.)

Inrush Current (Typ.)

Leakage Current

Protection

Over Load

Environment

Auxiliary Power

Power OK Signal

Output Voltage Trim

Working Temp.

Storage Temp. & Humidity

Working Humidity

Output Current Trim

Safety Standards

Withstand Voltage

Note.2

Note.3

Temp. Coefficient

Vibration

Power Factor (Typ.)

Over Temperature

±5.0% Typical adjustment by potentiometer. (VR1)

±2.0%

±1.0%

800ms, 100ms at full load

14ms / 230VAC at full load

90 ~ 264VAC, 127 ~ 370VDC

47 ~ 63Hz

105% rated output power

Protection type: Constant current limit

85 ±5°C detect on NTC, Protection type: Auto recovery after temperature goes down

Note.4

By external switch

Open drain signal low when PSU turns on, Max. sink current: 20mA, Max. drain voltage: 40V.

Adjustment of output voltage is between 0 ~ 105% of rated output

Adjustment of output current is between 0 ~ 105% of rated output

-25 ~ +60°C (Refer to load de-rating curve)

20 ~ 90% RH non-condensing

-40 ~ +85°C, 10 ~ 95% RH

±0.02% / °C (0 ~ 50°C)

Load and temperature control fan

Over Voltage

Remote ON / OFF Control

Isolation Resistance

EMI Conduction & Radiation

Power Harmonic & Voltage

Fluctuation and Flicker

EMS Immunity

Cooling

Dimension (WxHxD)

Packing

Function

Others

AE-1500-12

12V

125A

AE-1500-15 AE-1500-24 AE-1500-30 AE-1500-36

AE-1500-48

AE-1500-60

15V

24V

30V 36V

48V 60V

100A 62.5A 50A

41.7A

31.3A

25A

10 ~ 500Hz, 2G 10min. / 1cycle, period for 60min. each along X, Y, Z axes Compliance to IEC 68-2-6, IEC 68-2-64

I/P-O/P: 3KVAC (4242VDC), I/P-FG: 1.5KVAC (2121VDC), O/P-FG: 0.5KVAC (707VDC)

I/P-O/P, I/P-FG, O/P-FG: 100M Ohms / 500VDC

Certified EN 55022; EN 61204-3; EN 61000-6-3

Certified EN 61000-3-2; EN 61000-3-3

Certified EN 55024; EN6 1204-3; EN61000-6-1; IEC 61000-4-2, 3, 4, 5, 6, 8, 11

Certified UL 60950-1; EN 60950-1

89% 90% 92%

92%

93%

0 ~ 125A 0 ~ 100A 0 ~ 62.5A 0 ~ 50A 0 ~ 41.7A

0 ~ 31.3A

0 ~ 25A

1500W 1500W 1500W 1500W 1500W 1500W 1500W

150mVp-p 150mVp-p 240mVp-p 300mVp-p 360mVp-p 480mVp-p 600mVp-p

0.95 / 230VAC, 0.99 / 115VAC at ful load

18A / 115VAC, 9A / 230VAC

30A / 115VAC, 45A / 230VAC

< 2.5mA / 240VAC

2.6kg; 6pcs / 16.6kg / 1.86CUFT

127x64x280 mm / 5.00x2.52x11.02 inch

1500W Programmable Single Output

AE-1500 series

Safety & EMC

Note.6

Programmable output Voltage (0% ~ 105%)

Programmable output Current (0% ~ 105%)

Power OK signal

Remote ON / OFF, Remote sense function

Protection: OVP, OLP, OTP, Fan failure

Selectable +5V / 0.5A or +9V / 0.3A auxiliary output

Constant current limit

Remote setting multiple PSU via RS232, RS485 & I²C

Features:

Universal AC input / Full range

Selectable +5V / 0.5A or +9V / 0.3A auxiliary output

Note.7

Forced current sharing at parallel operation

Parallel (Current Sharing)

Please refer to page 5

Note.5

Note

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uF & 47uF parallel capacitor.

3. Tolerance: includes setup time tolerance, line regulation and load regulation.

4. De-rating may apply in low input voltage. Please check the de-rating curve for more details.

5. In parallel connection only one unit will operate if the total output load is less than 5% of the rated power.

6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

7. This test is done without enclosure: I/P-O/P 4242VDC. If with enclosure: I/P-O/P 2121VDC,I/P-FG:2121VDC, O/P-FG: 707VDC

Variable OVP, 120 ± 7% Vout. Refer to VCI VS OVP curve.

Protection type: Latch-style (Recovery after reset AC power ON or inhibit)

Global control via RS232

REV. C3

16/12/20

MTBF

111K HRS Certified MIL-HDBK-217F