Craftsman CMXZDCG498 Manual

Craftsman Garage døråbner CMXZDCG498

Læs gratis den danske manual til Craftsman CMXZDCG498 (4 sider) i kategorien Garage døråbner. Denne vejledning er vurderet som hjælpsom af 54 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 27.5 anmeldelser. Har du et spørgsmål om Craftsman CMXZDCG498, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Master
Link
Trolley
Connector
Retaining
Slot
Threaded
Shaft
Front Rail
Section
Master
Link
Idler Pulley
Retaining
Slot
Trolley
Connector
To remove rail pry both
end tabs of front
rail slightly outward
Idler Bolt hole
(KEEP LARGER
ONE ON TOP)
NEW
FRONT RAIL
CORRECT
INCORRECT
Rail Tab
Rail Tab
Eight-Foot (2.4 m) Rail Extension Kit
Model CMXZDCG498
REFER TO GARAGE DOOR OPENER MANUAL FOR DETAILED INSTALLATION,
ADJUSTMENTS, AND SAFETY INFORMATION.
To prevent possible SERIOUS INJURY or DEATH:
• Disconnect ALL electric and battery power BEFORE performing ANY service
or maintenance.
The garage door MUST be in the fully closed position during installation.
®
Figure 2
Figure 1
BEFORE YOU BEGIN:
• The trolley must be in down (closed door) position during assembly and
installation. If you have a completely installed garage door opener, the rail/
opener assembly must be taken down. The UP and DOWN travel must be
readjusted after installation.
• Opener hanging brackets will require repositioning and the addition of an extra
bracket for stability due to increased rail length.
• This may require two people for installation.
IF THIS IS A NEW INSTALLATION:
Use the front (header) rail section, belt assembly, and longer emergency release
rope in this kit in place of those packaged with the garage door opener. Complete
the assembly, installation, and adjustment of the opener according to the garage
door opener manual. Ensure that an additional hanging bracket is added for
stability, as detailed below.
IF THIS IS AN EXISTING INSTALLATION, CONTINUE AS FOLLOWS:
1. Pull down on the emergency release handle, then disconnect the trolley from
the door arm.
2. Disconnect the rail/opener assembly from the header bracket and hanging
brackets, and place it on the floor.
3. Remove the sprocket cover from the opener sprocket and set aside.
4. Disconnect the master link from the trolley threaded shaft and belt; discard
(Figure 1).
5. Remove the spring/nut from the trolley and discard.
6. Remove idler pulley assembly and set aside.
7. Remove the belt assembly and discard.
8. Push the trolley back toward the opener. Disconnect the front rail section by
using a screwdriver tip to pry up the outer tab on each side of the rail, then
slide it off the center rail. Discard the front rail .(Figure 2)
9. Align the new front rail with the existing rail assembly, keeping the cut out
“window” at the front (header) end. Be sure to keep it right side up: the idler
pulley bolt hole above the window is larger on top of the rail than on the
bottom. Slide the front rail onto the assembly; tabs along the side will lock
into place.
10. As a temporary stop, insert a screwdriver into the hole 10" (25 cm) from the
front end of the rail ). Slide the trolley assembly to this point.(Figure 1
11. Lay the new belt beside the rail. Grasp the end with the hooked trolley
connector and pass approximately 12" (30 cm) of belt through the window.
Keeping the ribbed side toward the rail, and allow it to hang while you
complete the next two steps.
12. Replace the idler pulley, lock washer and nut. Rotate it to be sure it spins
freely. Grease the center if necessary.
13. Locate the rail tab. Use a flathead screwdriver and lift the rail tab until the
tab is vertical (90°) . (Figure 2)
14. Pull the belt around the idler pulley and hook the trolley connector into the
retaining slot on the trolley . The ribbed side must contact the (Figure 1)
pulley.
15. With the trolley against the screwdriver, dispense the remainder of the belt
along the rail length toward the motor unit and around the sprocket
(Figure1). The sprocket teeth must engage the belt.
16. Check to make sure the belt is not twisted, then connect it to the flat end of
the trolley threaded shaft with the master link :(Figure 1)
• Push pins of master link bar through holes in end of belt and trolley
threaded shaft.
• Push master link cap over pins and past pin notches.
• Slide clip-on spring over cap and onto pin notches until both pins are
securely locked in place.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

Produkt Specifikationer

Mærke: Craftsman
Kategori: Garage døråbner
Model: CMXZDCG498

Har du brug for hjælp?

Hvis du har brug for hjælp til Craftsman CMXZDCG498 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Garage døråbner Craftsman Manualer

Craftsman

Craftsman CR-8X Manual

25 November 2025
Craftsman

Craftsman CMXZDCG498 Manual

25 Marts 2024
Craftsman

Craftsman 57943 Manual

1 September 2023
Craftsman

Craftsman 139.53753 Manual

31 Maj 2023
Craftsman

Craftsman CMXZDCG453 Manual

27 Maj 2023
Craftsman

Craftsman 57933 Manual

22 Maj 2023
Craftsman

Craftsman CMXEOCG771 Manual

28 November 2022

Garage døråbner Manualer

Nyeste Garage døråbner Manualer

Chamberlain

Chamberlain D1000C Manual

9 December 2025
Chamberlain

Chamberlain C1000C Manual

9 December 2025
Vevor

Vevor MD400 Manual

1 December 2025
Vevor

Vevor MD550 Manual

24 November 2025
Vevor

Vevor MD280 Manual

24 November 2025
Sommer

Sommer Twist M Manual

8 November 2025
Sommer

Sommer Twist ML Manual

7 November 2025
Sommer

Sommer Marathon Tiga SLX Manual

4 November 2025
Sommer

Sommer Twist M S3 Manual

3 November 2025
Sommer

Sommer Twist ML S3 Manual

3 November 2025