Crest Audio Versarray Mk III Manual

Crest Audio Ikke kategoriseret Versarray Mk III

Læs gratis den danske manual til Crest Audio Versarray Mk III (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Crest Audio Versarray Mk III, eller vil du spørge andre brugere om produktet?

Side 1/20
1
Crest Audio® Versarray™ Mk III
FlyQWIK™
Adjustable Rigging System
Crest Audio® Versarray™ Mk III Two Foot Fly Bar
FG# 03618490
Specications and Instructions
CAUTION ! Before attempting to suspend any Versarray™ Rigging Hardware with or without speak-
ers hung from it, consult a certied structural engineer. e Halo/Fly Bar and/or speaker array can
fall from improper suspension, resulting in serious injury and property damage. Use only the correct mat-
ing hardware. All associated rigging is the responsibility of others.
Description
e Crest Audio® Versarray™ Mk III Two Foot Fly Bar is used in conjunction with the Crest Audio® Versar-
ray™ Mk III Halo to provide additional multiple single-point hang balance points, increasing the number
available on the Halo alone from 8, to a total of 29 discrete points.
is part is an optional piece of the overall rigging system, and it may not be needed if the center bar of the
Halo provides an acceptable balance point for a single-point hang of the line array as congured and own.
It can also be used to y the Versarray™ Mk III Halo via two hang points at either end of the Versarray™ Mk
III Two Foot Fly Bar. See Figure 1 for the labeled FLy Bar holes.
Specications:
Overall Dimensions, H x W x L:
3.00” X 0.50” X 25.34” (1.2 cm X 1.3 cm X 64.4 cm)
Weight: 11 lbs.
Material: 1 / 2 ” thick by 3” solid steel alloy with eight 23mm rigging holes along the center of its length.
Finish: Entire Fly Bar is at black powder coated paint nish.
Recommended Shackle Specications
(Shackle NOT supplied with the Versarray™ Mk III Two Foot Fly Bar):
3/4” diameter pin Forged Carbon Steel Screw-pin Anchor Shackle
18mm or 20mm diameter pin based shackles can also be used, and the Stainless Steel alloy 316 can be an
alternate material for the shackle.
e shackle should be load rated for a minimum of 2 tons (4,000 lbs.), and shackles of this size and materi-
als oen have load ratings in excess of this.
Working Load Limit: 544 kg / 1,200 lbs. for Ultimate Strength Design Factor of 10:1
(is meets PLASA North America criteria and typically exceeds local USA safety requirements.)
Working Load Limit: 453 kg / 1,000 lbs. for Ultimate Strength Design Factor of 12:1
(is is in compliance with the European Union mandated Safety Factor)
Maximum Combined Pull-Back Angle, Two or less Subs in the hang: 30 degrees
Maximum Pull-Back Angle, more than 2 Subs in the hang: 15 degrees
2
NOTES:
The ultimate strength for the Versarray™ Mk3 loudspeaker system rigging points was determined utilizing
calibrated and certified pull tests.
CAUTION ! The Crest Audio® Versarray™ Mk III Two Foot Fly Bar is designed to be used ONLY in
conjunction with the Crest Audio® Versarray™ Mk III Halo ! It is not designed to fly any cabinets by itself,
nor should you attempt to do so!
CAUTIONS
WARNING !
IMPORTANT INFORMATION FOR STRUCTURAL ENGINEER AND RIGGING PERSONNEL. Before
you fly the array, be sure to inspect the rigging and flying hardware to insure that it is mechanically sound
and has not been damaged. There should be no significant distortion of the shape of the Halo cou-pling
ears, cabinet straps, Angle Slider bracket or Rail, Pivot Bar or a fly bar, and the hardware should be
checked for tightness.
CAUTIONS:
IF ANY OF THE BRACKETS, RAILS, CABINET STRAPS, PIVOT BAR OR THE FLY BAR HAS BEEN
DAMAGED OR DISTORTED, DO NOT USE, AND DO NOT FLY THE ARRAY UNTIL THEY CAN BE
REPLACED OR REPAIRED!
DO NOT USE THE PIVOT BAR OR ANGLE SLIDER BRACKET AS HANDLES TO TRANSPORT THE
CABINETS!
DO NOT TRANSPORT THE CABINETS IN ARRAY CONFIGURATION COUPLED TOGETHER, EX-CEPT
WITH THE RECOMMENDED TRANSPORT CART AND IN THE STIPULATED MANNER FOR THAT
CART. TRANSPORT IN SUCH AN UNAPPROVED MANNER VOIDS THE WARRANTY, AND THE
SYSTEM WOULD BE CONSIDERED UNSAFE TO BE FLOWN AFTER SUCH AN UNAPPROVED
TRANSPORT EVENT.
The Crest Audio® Versarray™ loudspeaker models should be suspended overhead only in accordance with the
procedures and limitations specified in the Users Manual and possible manual update notices. This system
should be suspended with certified rigging hardware by a rigging professional and in compliance
qualified
with local, provincial or national suspension ordinances. ALWAYS USE PROPER GRADE
HARDWARE.
It is the responsibility of the user and installer to make sure that any Crest Audio® Versarray™
installation meets any applicable local, state or federal safety regulations.
CAUTION: Before attempting to suspend this speaker, consult with a certified structural engineer.
Speaker can fall from improper suspension, resulting in serious injury and property damage. Use only the
correct mating hardware. All associated rigging is the responsibility of others. Maximum enclosure angle 30
degrees. Failure to follow proper rigging specifications listed in the manual may result in injury or death.
Whenever possible, in addition to the nominal primary mounting method, use a suitable safety chain or wire
rope attached to one of the other groups of fly points, and firmly attached to a suitable structural member as
indicated by a certified structural engineer. CAUTION: ALWAYS USE SAFETY CHAIN OR WIRE ROPE.


Produkt Specifikationer

Mærke: Crest Audio
Kategori: Ikke kategoriseret
Model: Versarray Mk III

Har du brug for hjælp?

Hvis du har brug for hjælp til Crest Audio Versarray Mk III stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Crest Audio Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer