Crestron C2N-RTHS Manual

Crestron Luftfugter C2N-RTHS

Læs gratis den danske manual til Crestron C2N-RTHS (2 sider) i kategorien Luftfugter. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Crestron C2N-RTHS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

C2N-RTHS

Temperature and Humidity Sensor

Installation Guide

Wiring

Make the necessary connections as called out in the illustration. Apply power after all

connections have been made.

CAUTION: Insufcient power can lead to unpredictable results or damage to the

equipment. Use the Crestron Power Calculator to help calculate how much power is

needed for the system (www.crestron.com/calculators).

NOTE: When wiring the Cresnet network, consider the following:

• Use Crestron Certied Wire.

• Use Crestron power supplies for Crestron equipment.

• Provide sufcient power to the system.

Wiring the C2N-RTHS

Description

The Crestron

C2N-RTHS is a wall-mounted temperature and relative humidity sensor that

communicates directly with any Crestron control system via the Cresnet

control network.

One-piece mounting makes the C2N-RTHS simple to install. The 1-1/2 in (38.1 mm)

diameter face protrudes just 1/8 in (3.2 mm) from the wall surface and is easily painted or

wallpapered to blend into the wall surface.

C2N-RTHS Specications

Installation

NOTES: Ensure the installation location is not close to a heat or humidity source and is

away from direct sunlight, skylights, and windows. When mounting the sensor outdoors,

do not place in direct sunlight, and do not place where the sensor will be directly

exposed to precipitation. Sensors are suitable for mounting in dry or damp locations as

dened by the National Electrical Code.

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• A licensed electrician should install this product.

• Mount sensors on a vibration-free surface.

NOTE: Before using the C2N-RTHS, ensure the device is using the latest rmware.

Check for the latest rmware for the C2N-RTHS at www.crestron.com/rmware. Load

the rmware onto the device using Crestron Toolbox™ software.

Complete the following procedure to install the C2N-RTHS:

1. Locate an area on the wall that is free of miscellaneous wiring and studs.

2. Make a small hole near the center of the designated mounting site to verify that the

location is suitable.

3. Drill or cut a 1 in (26 mm) diameter circular hole in the wall at the desired position.

4. Route the Cresnet wires to the sensor. Use the four wire nuts included to connect

the wires (red to red, white to white, blue to blue, and black to black).

Cresnet Wiring for the C2N-RTHS

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

Black Ground

Red 24 V

White Y

Blue Z

Wire nuts

Cresnet

wires

Pigtail wires

from sensor

Mounting clips

1 in (26 mm) hole

C2N-RTHS Front and Angled View

NOTE: The miniature setup button and red LED are used for setting the network ID

for the initial conguration or when the device is being added or replaced. They are

also used for touch-settable ID (TSID).

Mounting clips

Setup

button

Red

LED

C2N-RTHS Rear and Angled Views

10 in

(254 mm)

5. Press t the sensor into the hole; the clips on either side of the sensor hold it in

place.

NOTE: The face of the sensor may be painted or wallpapered to match the wall.

Ensure that paint does not enter (or that wallpaper does not cover) the perimeter

gap or the holes for the setup button and LED.

SPECIFICATION DETAILS

Measuring Range

Temperature -40º to 176 ºF (-40º to 80 ºC)

Humidity 0% to 100% RH

Output Resolution 0.1 ºF (0.1 ºC); 1% RH

Accuracy ±1.0 ºF (0.5 ºC); 5% RH

Temperature Accuracy

Over Full Range ±0.9 °F (0.5 °C)

At Room Temperature +0.2/-0.7 °F (+0.1/-0.4 °C)

Humidity Accuracy ±5%

Connection ~10 in (~25 cm) 4-wire pigtail;

Connects to Cresnet control network

Power Requirements

Cresnet Power Usage 0.25 W (0.01 Amps @ 24 Vdc)

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Luftfugter
Model:	C2N-RTHS
Type:	Indbygget
Bredde:	38.1 mm
Dybde:	56.4 mm
Højde:	38.1 mm
Forbindelsesteknologi:	Ledningsført
Formål:	Indendørs
Sensortype:	Temperatur og luftfugtighedssensor
Nøjagtighed:	0.1 °C
Temperatur måleinterval:	-40 - 80 °C
Fugtighed måleinterval:	0 - 100 %