Crestron CBLR-VGA Manual

Crestron Ikke kategoriseret CBLR-VGA

Læs gratis den danske manual til Crestron CBLR-VGA (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Crestron CBLR-VGA, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

quickstart guide

CBLR Series

www.crestron.com

Specifications subject to

change without notice.

CBLR Series

QUICKSTART DOC. 7245C (2032356, Sheet 1 of 2) 02.14

Cable Retractors for FlipTops™

For regulatory compliance information, refer to Doc. 7475.

NOTE: For preparation of FlipTop 600 Series models, refer to “Modify the FlipTop

(FlipTop 600 Series)” in the third column on this page.

Crestron® cable retractors provide a

convenient cable management solution

for use with most Crestron FlipTops™.

This solution allows a user to simply

reach into the FlipTop™ compartment

and pull out any cable to the desired

length. Each cable can be pulled out up

to 3 feet (0.9 meter). A simple press of

the easy-access lever retracts the cable

back into the compartment.

Each Crestron cable retractor features a patent-pending mechanism that dampens the rate of retrac-

tion to prevent the cable from whipping as it is pulled back into the FlipTop storage compartment. The

retraction speed is installer adjustable to ensure full and effortless retraction without excessive force.

Up to three or four cable retractors can be installed depending on the FlipTop model. Blank inserts

(CBLRA-INSERT-BLANK*) are required to fill any unused positions. As an alternative to a blank insert,

a 2-wire insert (CBLRA-INSERT-2WIRE* or FTA-CBLRA-INSERT-2WIRE-102*) is also offered to

accommodate additional non-retracting cables if needed.

Preparation

Preparation consists of:

• Modifying the FlipTop assembly to accommodate the cable retractors.

• Determining the desired mounting orientation. (Retractors are shipped configured for

horizontal orientation, but are easily reconfigured for vertical orientation.)

Modify the FlipTop (Non-FlipTop 600 Series)

1. Remove four screws A to detach

the lower bar assembly. Also remove

two screws B. Retain screws A and B

to attach the FlipTop mounting bracket

assembly. Refer to the FlipTop mounting

brackets table provided in section ➍ to

ensure that the mounting bracket received is

appropriate for the FlipTop being modified.

2. Remove four screws C to remove the

cable guide. Retain the screws to

attach the two side filler plates*.

3. Move the mounting bracket assembly

up into position and secure using four

screws A and two screws B.

4. Place the side filler plates in position

and secure using four screws C.

Mounting

Bracket

Assembly

Screws A

Screw B

Screws C

Attachment of Mounting Bracket

Assembly and Side Filler Plates

Side Filler

Plates

Removing Cable Guide and Lower Bar Assembly

Lower Bar

Assembly

Cable

Guide

Screws A

Screw B

Screws C

Mounting Bracket Assembly Installed

Mounting

Bracket

Assembly

Side Filler Plates Installed

Side Filler

Plates

Modify the FlipTop (FlipTop 600 Series)

Retractors can be installed in both the left and right sides of the FlipTop 600 Series models.

1. Remove the screw holding the cable guide in place, then remove the cable guide.

2. Remove the screws holding the cable pass-through bracket in place, then remove the cable

pass-through bracket.

3. Remove the shoulder screws from the front of the unit.

Save these as they are used in retractor installation.

* Item(s) sold separately.

Reconfigure Retractors for Vertical Operation

To reconfigure the retractors for vertical orientation, refer to the illustration below and do the following:

1. Remove the two screws D, one from each side of the retractor, attaching the neck in the horizontal

orientation.

2. Reposition the neck as shown in the vertical orientation view and attach using the two screws D

plus a third screw E (1/4 in, 6-32, flathead, supplied) to secure the neck in that position.

(2) Screws D

(One on Each Side)

Horizontal Orientation Vertical Orientation

(2) Screws D

(1) Supplied Screw

Side View

Reverse Side

Retractor

Neck

Retractor

Neck

Cable Guide

Cable Pass-Through Bracket

Shoulder Screws

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	CBLR-VGA
Type:	Kabelindtrækker
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Formål:	Skrivebord

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CBLR-VGA stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron HZ2-BTNS-5 Manual

7 Oktober 2025

Crestron HZ2-AUX Manual

7 Oktober 2025

Crestron PW-2407WUL Manual

29 September 2025

Crestron C2N-UNI8IO Manual

28 September 2025

Crestron CLXI-4HSW4 Manual

24 September 2025

Crestron GLD-LED-50W Manual

24 September 2025

Crestron TPS-4LW Manual

23 September 2025

Crestron Zūm Manual

23 September 2025

Crestron SIMPL Manual

23 September 2025

Crestron UC-FCM-T Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MSW PROPULLATOR 2500MH Manual

3 November 2025

ANCEL HD3200 Manual

3 November 2025

Lantronix C3220 Manual

3 November 2025

Cooler Master MasterBox MB511 Manual

3 November 2025

Klarstein La Palma 750 Smart Manual

3 November 2025

ANCEL AD610 Elite Manual

3 November 2025

ErgoAV ERIWA1-01W Manual

3 November 2025

QOLIXm YQAWSL-6A4U Manual

3 November 2025

ANCEL AJ400 Manual

3 November 2025

Emerson ITL9907RE Manual

3 November 2025