Crestron CLXI-4HSW4 Manual

Crestron Ikke kategoriseret CLXI-4HSW4

Læs gratis den danske manual til Crestron CLXI-4HSW4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Crestron CLXI-4HSW4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CLTI- & CLXI-4HSW4

Terminal Block & Module Locations (Single-wide Enclosure)

Functional Summary

MODULETERMINAL

BLOCK

GROUNDING

TERMINAL

BLOCK

The Crestron



4-Feed, 4-High-Inrush Switch Terminal

Block and Module (CLTI-4HSW4 and CLXI-4HSW4,

respectively), are considered a single entity and must be

used together. They ship separately to permit termination

of the field wiring to the CLTI-4HSW4 prior to

installation of the CLXI-4HSW4, as described in this

guide. They can be mounted in any Crestron Automation

Enclosure (CAEN-Series Enclosures). The terminal block

is designed to terminate four circuit feeds (HOT and

NEUTRAL) and distribute the controlled circuits (LOAD)

to the fixtures. The module connects to the terminal block

and performs switching (non-dim) control of four

incandescent, low voltage, neon, cold cathode,

fluorescent, or HID lighting loads, or motor loads. The

maximum load is 8 amps (1 HP) for each controlled

circuit (32 amps total per module). The unit requires

230VAC 50 Hz input voltage. An oversize heat sink

dissipates heat efficiently. There are LEDs on the module

to indicate communication to a Cresnet



network, input

power to the module, and output power to the load.

NOTE: When connecting to an Arc Fault Breaker,

the load should not exceed 1000 watts.

Terminal Block & Module Locations (Double-wide Enclosure)

Installation

GROUNDING TERMINAL BLOCKS

MODULETERMINAL BLOCK

(LEFT)

TERMINAL BLOCK

(RIGHT)

Terminal block and module must be mounted into a

Crestron Automation Enclosure by a licensed electrician,

in accordance with all national and local codes.

CAUTION: This equipment is for indoor use only

and needs to be air-cooled. Mount in a well-

ventilated area. The ambient temperature must be

0°C to 40°C (32°F to 104°F). The relative humidity

must be 0% to 90% (non-condensing).

Terminal blocks are installed along the left side of single-

wide enclosures and along the outside edges (left and

right sides) of double-wide enclosures. Modules are

installed along the right side of single-wide enclosures

and side-by-side in the center of double-wide enclosures.

When installing modules and terminal blocks in a double-

wide enclosure, be sure to invert units on the right side so

that they can be properly wired. Refer to the illustrations

shown in the next column when considering the location

of terminal blocks and modules within an enclosure.

NOTE: Modules and terminal blocks must be

installed into the lowest available spaces and

continue toward the top of the enclosure.

Crestron Electronics, Inc. Installation Guide – DOC. 6412

15 Volvo Drive Rockleigh, NJ 07647 (2013808)

Tel: 888.CRESTRON 11.05

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Terminal Block & Module Crestron CLTI- & CLXI-4HSW4

Terminal Block Installation and Field

Wiring

Wiring Diagram of the Terminal Block to the Feed and

Load(s) (Single-wide and Left Side Double-wide Enclosures)

LOAD

HOT 1 (*)

HOT 2 (*)

HOT 3 (*)

HOT 4 (*)

NEUTRAL

GROUNDING

TERMINAL

BLOCK

GND

TERMINAL

BLOCK

LEFT

SIDE

WIRING

LABEL

AREA FOR

MODULE

LOCATION

LABEL

BYPASS

JUMPERS

(*) FROM 10 OR 16 AMP

CIRCUIT BREAKER

1. Use the two supplied self-tapping pan Phillips

screws (8B x ¼-inch (6 mm) length) to secure

the terminal block and the appropriate (left or

right) wiring label to the Crestron Automation

Enclosure. The wiring label lies beneath the

terminal block as shown in the two wiring

diagrams on this page.

NOTE: Both left and right wiring labels are

provided. The left-side labels are common for both

single and double-wide enclosures. The right-side

labels are only used in double-wide enclosures since

the modules and terminal blocks along the right side

must be inverted when mounting.

CAUTION: On this terminal block there are four

distinct circuits. Bypass jumpers are installed on the

on the brown and red sections of each circuit on the

terminal block to allow testing of the circuits and to

protect the module during installation. When properly

secured by two screws, each bypass jumper on a

circuit shorts the hot to switch so that the circuit is

receiving power. Do not remove any bypass jumpers

until all feed and load wiring has been completed, the

circuit has been tested for electrical faults, and the

module has been installed. Refer to “Module

Installation” on the next page. Jumpers are also

installed on the blue sections of the terminal block

and tie the neutrals together. These jumpers should

never be removed.

Wiring Diagram of the Terminal Block to the Feed and

Load(s) (Right Side Double-wide Enclosures)

LOAD

HOT 1 (*)

HOT 2 (*)

HOT 3 (*)

HOT 4 (*)

NEUTRAL

GROUNDING

TERMINAL

BLOCK

GND

TERMINAL

BLOCK

RIGHT

SIDE

WIRING

LABEL

AREA FOR

MODULE

LOCATION

LABEL

BYPASS

JUMPERS

(*) FROM 10 OR 16 AMP

CIRCUIT BREAKER

NOTE: Use copper conductors only – rated 75°C

2. With the circuit breaker turned off, connect the

circuit feed (HOT and NEUTRAL) and

controlled circuit (LOAD) wires to the terminal

block per the markings provided on the wiring

label (as shown in the diagrams on this page).

Terminal blocks accept one 2.5 - 6.0 mm

wire.

Wires should be stripped to 12 mm. Tighten

terminal blocks to 1 Nm. Do not over tighten.

3. Grounding terminal blocks are available in the

cabinet for termination of ground wires. Tighten

to 4 Nm (2.5 - 6.0 mm

), 4.5 Nm (10.0 mm

), or

5.1 Nm (16 - 25 mm

4. Test the circuit for electrical faults by turning on

the circuit breaker and checking that the breaker

does not trip and that power is delivered to the

loads.

2 • Terminal Block & Module: CLTI- & CLXI-4HSW4 Installation Guide – DOC. 6412

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	CLXI-4HSW4
Bredde:	176 mm
Dybde:	87 mm
Højde:	193 mm
Antal pr. pakke:	1 stk

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLXI-4HSW4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron CLXI-4HSW4 Manual

24 September 2025

Crestron GLD-LED-50W Manual

24 September 2025

Crestron TPS-4LW Manual

23 September 2025

Crestron Zūm Manual

23 September 2025

Crestron SIMPL Manual

23 September 2025

Crestron UC-FCM-T Manual

23 September 2025

Crestron CBLR-HD Manual

23 September 2025

Crestron VC-4-ROOM-50-99 Manual

23 September 2025

Crestron CBLR-AUDIO Manual

23 September 2025

Crestron AM-3200-WF Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Celly TCSCREEN2C1A45W Manual

24 September 2025

T'nB CHCARW1V2 Manual

24 September 2025

Prebena 1GP-ALK35 Manual

24 September 2025

Clean Air Optima CA-607B Manual

24 September 2025

Konig & Meyer 260/1 Manual

24 September 2025

Bosch GSS 18V-10 Professional Manual

24 September 2025

Midea H1-(5-20)-E0 Manual

24 September 2025

T'nB CHNBTC65W Manual

24 September 2025

Zen Living 350010 Manual

24 September 2025

Summit Accucold FF28LWHMED2 Manual

24 September 2025