Crestron CSA-PWS40 Manual

Crestron Ikke kategoriseret CSA-PWS40

Læs gratis den danske manual til Crestron CSA-PWS40 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Crestron CSA-PWS40, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

The CSA-PWS40 and CSAI-PWS40 are outlet-mountable, 40 W, 24 VDC regulated power

packs that provide power for Crestron® CSM-QMTDC series roller shade or drapery track

motors. The CSA-PWS40 has a NEMA 1-15P blade insert installed and the

CSAI-PWS40 ships with a blade insert kit that consists of eight blade inserts.

The CSA-PWS40 and CSAI-PWS40 are ideally suited to provide local power for

CSM-QMTDC motors that communicate using the infiNET EX® network.

Check the Box

Item Qty

CSA-PWS40 or CSAI-PWS40 1

CSAI-PWS40 Only

Blade Insert Kit, 8 Blades, International 1

Dimensions

2.91 in.

(74 mm)

2.21 in.

(56 mm)

1.71 in.

(43 mm)

1.54 in.

(39 mm)

Install the Power Pack

NOTES:

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• An AC outlet must be located near the CSM-QMTDC series roller shade or drapery

track motor that is powered by the power pack. The power pack has an 8 ft (2.43 m)

long power cable.

Install the power pack:

1. Connect the flying leads from the power pack to the flying leads on the CSM-QMTDC

series roller shade or drapery track motor. Ensure that connections are properly made.

NOTE: To change the plug type on the CSAI-PWS40, refer to the “Change the Blade

Insert” section on the next page.

2. Plug the power pack into a 120 VAC power outlet.

Wiring Diagram Using a Cresnet Motor

Power Pack

To Cresnet

Motor

pigtail

24G

Z YG

Cresnet motor

Wiring Diagram Using an infiNET EX Motor

Motor

pigtail

24G

infiNET EX motor

Power Pack

CSA-PWS40/CSAI-PWS40

Power Pack for Crestron® CSM-QMTDC Series Roller Shade and Drapery Track Motors

Change the Blade Insert (CSAI-PWS40 Only)

1. If a blade insert is attached to the CSAI-PWS40, slide the spring-loaded locking key

downward and then pull upward on the blade insert to remove it.

2. Insert the top edge of the blade assembly into the top of the CSAI-PWS40 at

a 30-60 degree angle.

NOTE: The top edge of the blade assembly is flat, and the bottom edge is U-shaped.

The CSAI-PWS40 is shaped similarly.

3. Push the blade insert down into the CSAI-PWS40 until it locks into place. A clicking

sound will occur.

4. Pull up on the blade to check that the blade insert is securely installed.

Technical Specifications

Refer to the CSA-PWS40 product page at for a complete list of product

www.crestron.com

specifications.

Specification Details

Output Rating 24 VDC, 40 W (1.66 A), regulated

Power Requirements 1 A @ 100-240 VAC, 50/60 Hz

Connections

Line

Load

(1) power plug, line power input

(1) 8 ft (2.43 m) attached cable with inline ferrite core and

flying leads

Construction 94V-0 polycarbonate, white, outlet-mountable

Environmental

Temperature

Humidity

32º to 104ºF (0º to 40ºC)

15% to 95% RH (noncondensing)

Weight 6.4 oz (182 g)

Additional Information

Scan or click the QR code for detailed product information.

CSA-PWS40 CSAI-PWS40

Compliance and Legal

Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a

translation of the original instructions.

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.

This product is listed to applicable UL® Standards and requirements tested by Intertek® services.

Ce produit est homologué selon les normes et les exigences UL applicables par Intertek Prestations de service.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may

not cause harmful interference and (2) this device must accept any interference received, including interference that may

cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void

the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and infiNET EX are either trademarks or registered trademarks of Crestron Electronics, Inc.

in the United States and/or other countries. The ETL logo is either a trademark or registered trademark of Intertek Testing

Services NA in the United States and/or other countries. UL is either a trademark or registered trademark of Underwriters

Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names

may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron

disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or

photography.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRON

Fax: 201.767.7576

www.crestron.com

Quick Start - Doc. 7370D

(2053450)

05/15/19

Specifications subject to

change without notice.

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	CSA-PWS40

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CSA-PWS40 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Crestron Manualer

Crestron FT2A-CP-RJ45 Manual

9 Juni 2025

Crestron DIN-PWS60 Manual

9 Juni 2025

Crestron TS-770R Manual

9 Juni 2025

Crestron HD-CONV-USB-200 Manual

9 Juni 2025

Crestron CLT-1FAN4 Manual

8 Juni 2025

Crestron CLTIBN-2DIM8 Manual

8 Juni 2025

Crestron CLT-2DIMFLV8 Manual

8 Juni 2025

Crestron CAEN-CK-2X1 Manual

8 Juni 2025

Crestron FT2A-PWR-IS-2 Manual

8 Juni 2025

Crestron FT2A-CBLR-1T Manual

8 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan 1024W Manual

15 Juni 2025

Backyard Pro 554PL2030 Manual

15 Juni 2025

Haier 1U18TE2HDA Manual

15 Juni 2025

AEG EWKEXT1 Manual

15 Juni 2025

Planet XGPN-400AXV Manual

15 Juni 2025

Cadac 3 Cook Turbo Manual

15 Juni 2025

Bobrick B-3944 Manual

15 Juni 2025

Sony SZC-4008 Manual

15 Juni 2025

Watts ETX-15 Manual

15 Juni 2025

Sigma REMOTE ONE Manual

15 Juni 2025