Crestron HD-TX-201-C-2G-E Manual

Crestron AV forlænger HD-TX-201-C-2G-E

Læs gratis den danske manual til Crestron HD-TX-201-C-2G-E (2 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Crestron HD-TX-201-C-2G-E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

HD-TX-201-C-2G-E

DM Lite Multiformat Switch and Transmitter

2. Using a Phillips screwdriver (not included), attach the device to the electrical box using the

four included #6-32 x 3/4-inch truss combo head screws.

3. Attach a decorator-style faceplate (sold separately) to the front panel of the device using

four screws (not included).

DO Install the Device

Install the device into a 2-gang electrical box (not included). A minimum mounting depth of 2 inches

(51 mm) is required.

To install the device:

1. On the rear of the device, make connections to the TO RX and Ethernet ports.

NOTES:

• For the 24 Vdc power connection, connect a power pack to either the transmitter or

a compatible receiver. Do not connect a power pack to both devices simultaneously.

Power is transmitted over the cable that connects the TO RX port on the transmitter to

the FROM RX port on the receiver.

A power pack is not included with the transmitter. When the transmitter is used with a

DM Lite surface-mount receiver, the transmitter receives power from the power pack

that ships with and connects to the receiver.

• Cabling that connects the TO RX port to the FROM TX port is designed for

intrabuilding use only.

DO Check the Box

QTY ITEM PART NUM.

4 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

TO RX:

To FROM TX

link input of

receiver

Passive

pass-through

to front panel

Ethernet port

24 V

1.25 A:

From power pack

(not included)

24 G

DO GUIDE DOC. 8333A (2052143) 06.18

Specicat ions subject to change without not ice.

DO Connect the Device

Connect the device as required for the application.

The SERVICE port is for factory use only.

DO Congure the Device

To congure the device, do either of the following:

• If the transmitter connects to an HD-RX-201-C-E, the HD-RX-201-C-E hosts the

conguration of the transmitter. As a result, congure the transmitter using the web

interface of the HD-RX-201-C-E.

To access the web interface, open a web browser and then go to the IP address of the

HD-RX-201-C-E. By default, DHCP is enabled. To display the IP address on the

connected HDMI® display, press the button on the front panel of theSETUP

HD-RX-201-C-E. Pressing the button on the transmitter will also display theSETUP

IP address of the HD-RX-201-C-E.

To log in to the web interface, enter the user name and password. The default user name

and password are both .admin

• If the transmitter does not connect to an HD-RX-201-C-E, refer to Answer ID 1000168

in the Online Help section of the Crestron website (www.crestron.com/onlinehelp) for

conguration information.

NOTE: When the transmitter does not connect to the HD-RX-201-C-E, pressing the

SETUP button on the transmitter has no effect.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The s pecic patents t hat cover Crestron products are listed at .

www.crestron.com/legal/patents

The product warrant y can be found at .www.crestron.com/legal/sales-terms-conditions-warranties

Cert ain Crestron products cont ain open source sof t ware. For specic information, visit . www.crestron.com/legal/open-source-soft ware

Crest ron and the Crestron logo are either trademarks or regist ered t rademarks of Crestron Electronics, Inc., in the U nit ed States and/or other countries. HDMI and t he HDMI logo are either

trademarks or registered t rademarks of HDMI Licensing LLC in t he United St ates and/or ot her count ries. UL and the UL logo are eit her t rademarks or registered trademarks of Underwriters

Laboratories, Inc. in the United States and/or other countries. Ot her trademarks, registered trademarks, and t rade names may be used in t his document to refer t o eit her t he ent ities claiming

the marks and names or t heir product s. Crestron disclaims any propriet ary interest in the marks and names of others. Crest ron is not responsible for errors in t ypography or photography.