Crestron HD-RXC-101-C-E Manual

Crestron AV forlænger HD-RXC-101-C-E

Læs gratis den danske manual til Crestron HD-RXC-101-C-E (2 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 29 anmeldelser. Har du et spørgsmål om Crestron HD-RXC-101-C-E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

HD-TX/HD-RX 101 Series

DM Lite Transmitters and Receivers

DO Install the Device

The Crestron® HD-TX/HD-RX 101 Series consists of transmitters and

receivers that are available as surface-mount devices and wall plates.

The surface-mount devices consist of the HD-TX-101-C-E and

HD-TXC-101-C-E transmitters and the HD-RX-101-C-E and

HD-RXC-101-C-E receivers. The wall plates consist of the

HD-TX-101-C-1G-E and HD-TXC-101-C-1G-E transmitters and the

HD-RX-101-C-1G-E and HD-RXC-101-C-1G-E receivers.

Install the Surface-Mount Device

Mount the device onto a at surface or rack rail.

Mount onto a Flat Surface

Using four mounting screws (not included), mount the device onto a at

surface such as a wall.

Wall Mounting

Mount onto a Rack Rail

Mount the device onto the front or rear rail of a rack. Position either the

left or right mounting ange of the device so that the holes align with the

holes in the rack. Then, secure the device to the rack using two mounting

screws (not included).

Rail Mounting

Install the Wall Plate

Install the wall plate into a 1-gang electrical box (not included):

1. Connect the rear of the wall plate by doing either of the following:

• If the wall plate is a transmitter, connect the TO RX port.

• If the wall plate is a receiver, connect the FROM TX port.

NOTES:

• For the 24 Vdc power connection, connect a power pack to

either a transmitter or receiver. Do not connect a power pack

to both devices simultaneously. Power is transmitted over the

cable that connects the TO RX port on the transmitter to the

FROM TX port on the receiver.

Power packs are not included with the wall plates but are

included with the surface-mount devices. When a wall plate

connects to a surface-mount device, power both devices

by connecting the included power pack to the

surface-mount device.

• Cabling that connects the TO RX port to the FROM TX port is

designed for intrabuilding use only.

2. Using a Phillips screwdriver (not included), attach the device to

the electrical box using the two included #6-32 x ¾ inch truss

combo head screws.

3. Attach a Crestron FP-G1 Series decorator-style faceplate

(sold separately) to the front panel of the device using two

screws (not included).

Installation into Electrical Box

DO Connect the Device

Connect the device as required for the application.

Connect the Transmitter

HD-TX-101-C-E Front Panel Connections

HD-TX-101-C-1G-E Front Panel Connections

HD-TXC-101-C-E Front Panel Connections

HD-TXC-101-C-1G-E Front Panel Connections

DO Check the Box

QUANTITY ITEM PART NUMBER

HD-TX-101-C-E and HD-RX-101-C-E

1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870

HD-TXC-101-C-E and HD-RXC-101-C-E

1 Connector, 3-Pin 2003575

1 Connector, 4-Pin 2003576

1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2045870

HD-TX-101-C-1G-E and HD-RX-101-C-1G-E

1 Connector, 2-Pin 2003574

2 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

HD-TXC-101-C-1G-E and HD-RXC-101-C-1G-E

1 Connector, 2-Pin 2003574

1 Connector, 3-Pin 2003575

1 Connector, 4-Pin 2003576

2 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

24 V

1.25 A:

From power pack

(not included)

TO RX

(Transmitter):

To FROM TX

link input port

of receiver

OR FROM TX

(Receiver):

From TO RX

link output port

of transmitter

POWER ONLY:

To Crestron® active cable

(sold separately, for example,

CBL-MULTI-HD-6)

HDMI IN:

From HDMI®

audio/video source

24 V

1.25 A:

From included

power pack 1

TO RX:

To FROM TX

link input port

of receiver2

HDMI IN:

From HDMI

audio/video

source POWER ONLY:

To Crestron active

cable (sold separately,

for example,

CBL-MULTI-HD-6)

IR IN:

From Crestron

IR control port or

other IR signal source3

IR OUT:

To Crestron

IRP2 emitter

(sold separately)4

COM:

To RS-232

device5

POWER ONLY:

To Crestron active cable

(sold separately, for example,

CBL-MULTI-HD-6)

HDMI IN:

From HDMI

audio/video source

TO RX:

To FROM TX

link input port

of receiver2

24 V

1.25 A:

From included

power pack1

IR IN:

From Crestron

IR control port or

other IR signal source3

HDMI IN:

From HDMI

audio/video source

POWER ONLY:

To Crestron active cable

(sold separately, for example,

CBL-MULTI-HD-6)

IR OUT:

To Crestron IRP2 emitter

(sold separately)4

COM:

To RS-232 device5

DO GUIDE DOC. 8310B (2051247) 07.18

Specicat ions subject t o change without not ice.

Connect the Receiver

HD-RX-101-C-E Front Panel Connections

HD-RX-101-C-1G-E Front Panel Connections

HD-RXC-101-C-E Front Panel Connections

HD-RXC-101-C-1G-E Front Panel Connections

DO Congure the Device

To congure the device, do either of the following:

• If a DM Lite transmitter connects to an HD-RX-201-C-E, congure

the transmitter using the web interface of the HD-RX-201-C-E.

The HD-RX-201-C-E hosts the conguration of the transmitter.

To access the web interface, open a web browser and then go

to the IP address of the HD-RX-201-C-E. By default, DHCP is

enabled. To display the IP address on the connected HDMI

display, press the button on the front panel of the SETUP

HD-RX-201-C-E.

To log in to the web interface, enter the user name and password.

The default user name and password are both .admin

• If a DM Lite transmitter connects to a DM Lite receiver other than

an HD-RX-201-C-E, refer to Answer ID 1000168 in the Online Help

section of the Crestron website (www.crestron.com/onlinehelp) for

conguration information.

DO Observe the LEDs

Observe the following LEDs:

• Lights green to indicate that the device is powered onPWR:

• HDMI IN: (Transmitter only) Lights green to indicate that the

device is receiving an HDMI signal

• (Receiver only) Lights green to indicate that the HDMI OUT:

device is transmitting an HDMI signal

• (Surface-mount devices only) Lights green to indicate LINK:

that a link has been established between the TO RX port on the

transmitter and the FROM TX port on the receiver

LEDs (Surface-Mount Transmitter Shown)

Connect a power pack to either the transmitter or receiver. Do not connect a power pack

to both devices simultaneously. Power is transmitted over the cable that connects the

TO RX port on the transmitter to the FROM TX port on the receiver.

2 Cabling that connects the TO RX port to the FROM TX port is designed for intrabuilding

use only.

3 The IR IN port on the transmitter passes the IR signal to the IR OUT port on the receiver.

4 The IR OUT port on the transmitter transmits the IR signal from the IR IN port on

the receiver.

5 The COM port on the transmitter passes RS-232 data to or from the COM port on

the receiver.

6 The IR IN port on the receiver passes the IR signal to the IR OUT port on the transmitter.

7 The IR OUT port on the receiver transmits the IR signal from the IR IN port on

the transmitter.

8 The COM port on the receiver passes RS-232 data to or from the COM port on

the transmitter.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specic patents t hat cover Crestron products are listed at . The product warrant y can be found at .

www.crestron.com/legal/patents www.crestron.com/legal/sales-terms-conditions-warranties

Cert ain Crestron products cont ain open source sof t ware. For specic information, visit . www.crestron.com/legal/open-source-soft ware

Crest ron and the Crestron logo are either trademarks or regist ered t rademarks of Crestron Elect ronics, Inc., in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in t he United States and/or ot her count ries.

UL and the UL logo are eit her trademarks or registered trademarks of Underwriters Laboratories, Inc. in the Unit ed States and/or other countries. Other trademarks, regist ered t rademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Crest ron disclaims any proprietary interest in t he marks and names of others. Crestron is not responsible f or errors in t ypography or phot ography.