Crestron RMC3 Manual

Crestron Ikke kategoriseret RMC3

Læs gratis den danske manual til Crestron RMC3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Crestron RMC3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

RMC3

3-Series® Room Media Controller

DO Install the Device

The Crestron®

RMC3 can be mounted onto a at surface or

a standard DIN rail using the included mounting bracket. The

RMC3 is shipped with the mounting bracket attached.

CAUTION: To prevent overheating, do not operate this product

in an area that exceeds the environmental temperature range

listed on the product web page.

NOTE: Rack mount and pole mount kits (sold separately) are

also available as mounting options for the RMC3.

Surface Mounting

To mount the RMC3 onto a at surface, use the following

procedure. (Refer to the image below.)

1. Detach the RMC3 from the mounting bracket by pulling the

left and right anges of the bracket outward to release the

tabs that hold the RMC3 in place.

2. Attach the mounting bracket to the at surface using the

four mounting holes in each corner of the bracket and the

appropriate mounting screws (not included).

3. Align the slots on the bottom of the RMC3 with the RMC3

mounting tabs on the bracket, and then press the RMC3

into the bracket until the RMC3 snaps into place.

4. (Optional) Secure the RMC3 in the mounting bracket by

screwing the two included 6-32 x 3/8" Phillips pan head

screws into the holes on the left and right of the assembly.

DIN Rail Mounting

To mount the RMC3 onto a DIN

rail, use the following procedure.

(Refer to the image below.)

1. Detach the RMC3 from the

mounting bracket by pulling the left and right anges of the

bracket outward to release the tabs that hold the RMC3 in

place.

2. Using a at-head screwdriver, pull the DIN rail release tab

downward.

3. Position the DIN rail mounting tabs (located on the rear of

the bracket, not shown) over the top edge of the DIN rail,

and then push the DIN rail release tab upward to lock the

mounting bracket onto the rail.

4. Align the slots on the bottom of the RMC3 with the RMC3

mounting tabs on the bracket, and then press the RMC3

into the bracket until the RMC3 snaps into place.

5. (Optional) Secure the RMC3 in the mounting bracket by

screwing the two included 6-32 x 3/8" Phillips pan head

screws into the holes on the left and right of the assembly.

DO Make Connections

Make any necessary connections as called out in the diagrams

to the right. Apply power after all connections have been made.

NOTE: A power supply is not included. The device requires a

PoE injector or a PoE switch (both sold separately).

NOTE: Ensure the unit is properly grounded by connecting the

chassis ground lug to an earth ground (building steel).

DO Check the Box

QTY PRODUCT COLOR PART NUM.

1 Adapter, USB to USB Mini 2037338

1 Bracket, Mounting, Integrated DIN Rail Clip Black 4519035

1 Cable, USB 2.0, A - Mini B, 6' 6" (2 m) Black 2025146

2 Connector, 3-Pin 2003575

2 Connector, 4-Pin 2003576

1 Connector, 5-Pin 2003577

2 Screw, 6-32 x 3/8", Pan Head, Phillips Black 2007225

Mounting

bracket

Left

ange Right

ange

Screws, Phillips

pan head (2):

6-32 x 3/8"

Left

ange DIN rail

release tab

Right

ange

Screws, Phillips

pan head (2):

6-32 x 3/8"

Mounting

bracket

DIN rail

(not included)

LAN PoE:

10 Base-T / 100 Base-TX

Ethernet to LAN

USB-OTG:

To computer console

or USB storage device

NET:

To any Cresnet®

network device

Ground

COM: To/from

RS-232/422/485

devices

IR 1−2:

To IR controlled

devices

RELAY 1−2:

To controllable

devices

DIGITAL IN (1−2):

From control

devices

PORT RS-232 RS-4221RS-485

GND GND GND GND 2

TX TX (from RMC3) TX- (from RMC3) TX-/RX-

RX RX (to RMC3) RX+(to RMC3) Not Used

RTS RTS (from RMC3) TX+ (from RMC3) TX+/RX+

CTS CTS (to RMC3) RX- (to RMC3) Not Used

1. RS-422 transmit and receive are balanced signals requiring two lines plus a ground in

each direction. RX D+ and TXD+ should idle high (going low at start of data transmission).

RXD- and TXD- should idle low (going high at start of data transmission). If necessary,

RXD+/R XD- and T XD+/T XD- may be swapped to maintain correct signal levels.

2. A ground terminal connection is recommended but not required.

COM 1 Connections

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Ikke kategoriseret
Model:	RMC3
Bredde:	128 mm
Dybde:	73 mm
Højde:	35 mm
Vægt:	180 g
Produktfarve:	Sort
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Intern hukommelse:	0.256 GB
Intern lagerkapacitet:	4096 GB
Opbevaringsmedietype:	Flash
Varmeafgivelse:	17 BUT/t