Crestron SAROS PDS8T-B-T-EACH Manual

Crestron Subwoofer SAROS PDS8T-B-T-EACH

Læs gratis den danske manual til Crestron SAROS PDS8T-B-T-EACH (2 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Crestron SAROS PDS8T-B-T-EACH, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Saros

Pendant Speakers

quickstart guide

SAROS_PD4T/PD6T/PD8T/PDS8T

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

SAROS_PD4T/PD6T/PD8T/PDS8T

Install/Remove Grille

The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is

included to prevent any possibility of the grille falling from the ceiling. Attach the tether to the

baffle using the supplied screw, cover the screw with the rubber boot provided, and place the

grille in position on the speaker. To remove the grille, insert the supplied pick accessory in

one of the side edge grille holes and pull the grille away from the speaker. To remove the

grille completely, disconnect the monofilament tether from the speaker baffle.

Set the Transformer Tap Selector Switches

The speakers are equipped with a 70V/100V matching transformer for distributed audio

systems. The transformer tap selector switch on the front panel is used to set the speaker

power level. Use a flat-head screwdriver to adjust the switch.

• For SAROS_PD4T 70V systems, use the left-side settings and select from 1.88, 3.75,

7.5, 15, or 30 watts.

• For SAROS_PD4T 100V systems, use the right-side settings and select from 3.75,

7.5, 15, or 30 watts. The X position should not be used.

• For SAROS_PD6T, SAROS_PD8T and SAROS_PDS8T 70V systems, use the

left-side settings and select from 3.75, 7.5, 15, 30, or 60 watts.

• For SAROS_PD6T, SAROS_PD8T and SAROS_PDS8T 100V systems, use the

right-side settings and select from 7.5, 15, 30, or 60 watts. The X position should not

be used.

The switch may also be set to 8 Ω operation, bypassing the transformer completely. This

setting should be used only for 8 Ω audio systems.

QUICKSTART DOC. 7488B (2037418) 10.15

Installation

Saros

speakers by Crestron

deliver professional grade

performance and flexible installation in a range of popular

sizes for demanding commercial applications. Solid

construction and high-end components are hallmarks of the

complete Saros speaker line.

Ideal for use in background or foreground music, paging,

and sound reinforcement systems, Saros speakers are

engineered to achieve smooth, even coverage, high output,

and clear, natural sound quality through the employment of

horn-loaded titanium dome tweeters, high-efficiency

damped cone woofers, ported enclosures, and precisely

tuned crossovers.

Front View - Grille Removed

Install Speaker Cable

Observe all local codes and install speaker cable from the audio source location to the

closest ceiling truss location where a speaker will be suspended, allowing sufficient length to

hang down slightly below the planned speaker height. If the speakers are to be connected in

parallel, install a second cable at that location and route it to the next speaker location.

Repeat this process at each speaker location.

Install Wire Rope

1. For each speaker to be installed, remove the top cover and route

the free end of one of the 15 ft (~5m) wire ropes supplied in the

SPKA-ST-15 Safety Tether/Tie Down Kit up through the top cover.

Connect the attached hook assembly to secure the wire rope to the

speaker rigging point.

2. Attach the free end of the wire rope to the ceiling truss, adjust the

length so the speaker is at the desired height, and secure it using

the supplied Gripple

wire rope grip. (Refer to the supplied

instructions for proper use of the Gripple.)

1. Refer to the illustration to the right, with the top cover off to expose the supplied

terminal block.

2. At each speaker location, route the speaker cable(s) hanging from the ceiling area

through the top cover, and dress the cables to the wire rope using plastic cable ties.

3. If using a supplied weather boot, slide the speaker cables through the weather boot.

Strip the ends of the cables approximately 1/8" to 3/16" (~3 mm to ~5 mm) and, if the

wire is stranded, twist the strands.

4. Connect the wires from the amplifier (or the previous speaker) to the supplied terminal

block, using the IN terminals; red to + and black to –. Use the THRU + and – terminals

to connect the speaker wires to the next (parallel) speaker.

5. Speaker removal is accomplished by reversing steps 1 through 4 above.

Paint the Speaker and Grille

Speaker and grille painting should be done prior to mounting.

1. Carefully remove the material on the underside of the grille, and set it aside for

reinstallation. It may be necessary to use a knife or other sharp instrument to free an

edge of the material so it can be peeled away. Use care to avoid cutting or tearing the

material.

2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the

holes in the grille.

3. Once the paint is dry, reinstall the material to the underside.

4. Remove the speaker top cover and paint the top cover and main speaker assembly

separately, being careful to mask areas that should not be painted.

100V

70V

For SAROS_PD6T/PD8T/PDS8T

100V

70V

For SAROS_PD4T

100V

70V

THRU

Terminal

Block

Connect Speaker Cables

Speaker

Cables

Top

Cover

Speaker

Rigging Point

(Wire Rope Not

Shown)

Speaker

Rigging Point

Connect or Disconnect Speakers

NOTE: If the speakers are to be connected in parallel, the sum of the power settings

for all speakers must be less than the power amplifier’s power/channel rating.

Attach grille safety

tether with supplied

screw. Cover screw

with supplied rubber

plug.

Saros Pendant speakers include a top cover that conceals the wiring connections and suspension

hardware for a very clean, contoured appearance. The speakers are available in white or black and can

be painted to blend with the surrounding architecture.

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Subwoofer
Model:	SAROS PDS8T-B-T-EACH

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron SAROS PDS8T-B-T-EACH stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Subwoofer Crestron Manualer

Crestron Saros PDS8T-W-T-EACH Manual

20 August 2024

Crestron Saros ICS8T-W-T-EACH Manual

20 August 2024

Crestron SAROS ICS8T-B-T-EACH Manual

20 August 2024

Crestron SAROS PDS8T-B-T-EACH Manual

20 August 2024

Crestron Vector SUBS15 Manual

19 August 2024

Crestron Vector SUBD18 Manual

19 August 2024

Crestron Vector SUBS18 Manual

19 August 2024

Subwoofer Manualer

Nyeste Subwoofer Manualer

Earthquake Sound Nova FF12 Manual

2 November 2025

Monoprice MSUB-A082 Manual

2 November 2025

NEAR IGS12M Manual

2 November 2025

DS18 BRO-BASS Manual

1 November 2025

Memphis Audio 15-PRX8D4 Manual

19 Oktober 2025

Audison Prima APBMW S8-4 Manual

18 Oktober 2025

Wavtech thinPRO12-2 Manual

14 Oktober 2025

Mackie ThumpSub GO Manual

8 Oktober 2025

Morel Ultimo Titanium 102 Manual

6 Oktober 2025

Fusion SG-SL102SPW Manual

6 Oktober 2025