Crestron TST-600-BTP Manual

Crestron Ikke kategoriseret TST-600-BTP

Læs gratis den danske manual til Crestron TST-600-BTP (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Crestron TST-600-BTP, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
DO GUIDE
DO Check the Box
QUANTITY PRODUCT PART NUMBER
2 Tape, Perforated, 1" x 1" 2023162
1 Tape, Perforated, 1" x 2" 2023163
1 Metal T-Pin 2020478
TST-600-BTP
Battery Pack for TST-600 and TST-602
The Crestron
®
integrated wiring. It has a multipin connector that attaches to the inside of
the TST-600 or TST-602.
TST-600-BTP with Multipin Connector
DO Remove the Old Battery Pack
NOTE: The TST-600 and TST-602 Wireless Touch Screens contain
electrostatic discharge (ESD) sensitive devices. To avoid damaging the
unit, perform the following procedure while wearing a grounding strap
that is properly grounded or while working on a grounded workstation.
NOTE: To prevent damage to the multipin connector and wiring, use care
when handling the TST-600-BTP.
Perform the following procedure to remove the existing TST-600-BTP
from a TST-600 or TST-602 touch screen. A #1 Phillips screwdriver is
required.
1. Use the included T-pin to slide the battery switch on the rear to the
off (down) position. Then place the touch screen face down on a
clean, padded work surface.
2. Remove the four screws that secure the front bezel to the touch
screen and return the unit to its normal, face-up position. (Use care
and hold the bezel against the touch screen.)
3. Unsnap the front bezel and lift it off of the touch screen and then
place the touch screen assembly face down on the work surface.
4. Carefully remove the rear of the enclosure from the touch screen
by grasping the support frame at the left and right edges, gently
spreading the edges (as shown in the following image), and then
lifting the assembly. It snaps out of the enclosure.
5. Remove the orange tape securing the battery pack wires to the
assembly.
6. Gently separate the multipin connector from the corresponding
connector on the circuit board of the touch screen.
7. Remove battery cells, with the connecting wires attached, from both
sides of the assembly.
DO Install the New Battery Pack
NOTE: The TST-600 and TST-602 Wireless Touch Screens contain
electrostatic discharge (ESD) sensitive devices. To avoid damaging the
unit, perform the following procedure while wearing a grounding strap
that is properly grounded or while working on a grounded workstation.
After removing the old TST-600-BTP from the touch screen, perform
the following procedure to install the new TST-600-BTP. A #1 Phillips
screwdriver is required.
1. Inspect the wire insulation on the battery pack and verify that it
extends to the battery wrap and is free of nicks or damage.
2. Orient the TST-600-BTP so the wires exiting the battery are facing
the connector on the touch screen.
3. Slide the right stack wires (those closest to the connector) into the
PCB channel, angling the top of the stack into the pocket of the ex
support tray.
4. Fully seat the right stack into the right pocket of the ex support tray
and verify that the wires have not been damaged during installation.
5. Connect the battery pack harness to the PCB connector.
6. With the wire harness positioned above the installed insulator, slide
the left stack wires into the PCB channel, angling the top of the stack
into the pocket of the ex support tray.
7. Fully seat the left stack into the left pocket of the ex support tray
and verify that the wires have not been damaged during installation.
8. Verify that the battery pack is connected and that the stacks are fully
seated into the left and right pockets.
9. Dress the battery wires as shown in the following image. Use the
2 1/2 inch (64 mm) long piece of orange tape to secure the wires.
NOTE: When routing the wires, avoid blocking the battery switch.
Battery Cells
Connector
Connectors
The connectors are aligned.
Seat the right stack in
the ex tray.
UP
Screws Screws

Produkt Specifikationer

Mærke: Crestron
Kategori: Ikke kategoriseret
Model: TST-600-BTP

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron TST-600-BTP stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Crestron Manualer

Crestron

Crestron HZ2-BTNS-5 Manual

7 Oktober 2025
Crestron

Crestron HZ2-AUX Manual

7 Oktober 2025
Crestron

Crestron PW-2407WUL Manual

29 September 2025
Crestron

Crestron C2N-UNI8IO Manual

28 September 2025
Crestron

Crestron CLXI-4HSW4 Manual

24 September 2025
Crestron

Crestron GLD-LED-50W Manual

24 September 2025
Crestron

Crestron TPS-4LW Manual

23 September 2025
Crestron

Crestron Zūm Manual

23 September 2025
Crestron

Crestron SIMPL Manual

23 September 2025
Crestron

Crestron UC-FCM-T Manual

23 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Iogear

Iogear SYMMETRE II GME640 Manual

1 November 2025
Hendi

Hendi 710241 Manual

1 November 2025
Beverage-Air

Beverage-Air Horizon HFP2HC-1G Manual

1 November 2025
Cooler Master

Cooler Master Scout 2 N2 Manual

1 November 2025
Beverage-Air

Beverage-Air Horizon HRP2HC-1G Manual

1 November 2025
Homedics

Homedics Ellia Stone ARM-810-TP-AU Manual

1 November 2025
HMS Premium

HMS Premium DD200 Manual

1 November 2025
Arktic

Arktic 274071 Manual

1 November 2025
Uniprodo

Uniprodo UNI_WATER_28 Manual

1 November 2025
Beverage-Air

Beverage-Air Horizon HFP2HC-1HG Manual

1 November 2025