Ctek MXS 10.0 Manual

Ctek Batterioplader MXS 10.0

Læs gratis den danske manual til Ctek MXS 10.0 (6 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Ctek MXS 10.0, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
EN
EN • 3
CONGRATULATIONS
to the purchase of your new professional switch mode battery charger.
This charger is included in a series of professional chargers from CTEK AB and SWEDEN
represents the latest technology in battery charging.
CTEK COMFORT CONNECT – eyelet M8
CTEK COMFORT CONNECT
MAINS CABLE
CTEK COMFORT CONNECT – clamp
CHARGE CABLE
SUPPLY PLUG*
*Supply plugs m ay differ to suit your wall socket.
Attach t he temperat ure sensor to the charger.
Attach t he temperat ure sensor to the clamp.
NORMAL
BATT ERY
PROGRAM
ERROR LAMP
AGM
BATT ERY
PROGRAM
FULLY DCHARGEREADY TO USE
RECOND
PROGRAM
SUPPLY
PROGRAM
POWER
LAMP
CHARGING
1. Connect the charger to the battery.
2. Connect the charger to the wall socket. The power lamp will indicate that the mains
cable is connected to the wall socket. The error lamp will indicate if the battery clamps
are incorrectly connected. The reverse polarity protection will ensure that the battery
or charger will not be damaged.
3. Press the MODE-button to select charging program.
4. Follow the 8-step display through the charging process.
The battery is ready to start the engine when STEP 4 is lit.
The battery is fully charged when STEP 7 is lit.
5. Stop charging at any time by disconnecting the mains cable from the wall socket.
MODE-
BUT TON
TEMPERATURE
SENSOR
TEMPERATURE
SENSOR
INDICATOR
MANUAL
1
1
2
2
20014905E MXS 10, Manual EU, Print file 004.indd 3 2011-10-11 08:50:46
4 • EN
BATTERY SIZE (Ah) TIME TO 80% CHARGED
20Ah 2h
50Ah 5h
100Ah 10h
200Ah 20h
READY TO USE
The table shows the estimated time for empty battery to 80% charge
CHARGING PROGRAMS
Settings are made by pressing the MODE-button. After about two seconds the charger
activates the selected program. The selected program will be restarted next time the
charger is connected.
The table explains the different Charging Programs:
Program Battery
Size (Ah) Explanation Temp range
20–300Ah
Normal battery program
14.4V/10A. Use for WET batteries,
Ca/Ca, MF and for most GEL batteries
-20°C–+50°C
(-4ºF–122ºF)
AGM 20–300Ah AGM battery program 14.7V/10A
Use for AGM batteries.
-20°C–+50°C
(-4ºF–122ºF)
RECOND 20–300Ah
Recond program 15.8V/1.5A
Use to return energy to the empty
WET and Ca/Ca batteries. Recond
your battery once per year and after
deep dischare to maximise lifetime
and capacity. The Recond program
adds STEP 6 to the normal battery
program. Frequent use of the Recond
program may cause water loss in the
batteries and reduce service life of
electronics. Contact your vehicle and
battery supplier for advice.
-20°C–+50°C
(-4ºF–122ºF)
20–300Ah
Supply program 13.6V/10A
Use as 12V power supply or use for
float maintenance charging when 100%
capacity of the battery is required.
Supply program activates step 7 without
time or voltage limitation.
-20°C–+50°C
(-4ºF–122ºF)
ERROR LAMP
If the error lamp is lit, check the following:
1. Is the chargers positive lead connected to the batterys
positive pole?
2. Is the charger connected to a 12V battery?
3. Has charging been interrupted in STEP 1, 2 or 5?
Restart the charger by pressing the MODE-button. If charging is still
being interrupted, the battery...
STEP 1: ...is seriosly sulphated and may need to be replaced.
STEP 2: ...can not accept charge and may need to be replaced.
STEP 5: ...can not keep charge and may need to be replaced.
TEMPERATURE SENSOR
The MXS 10 is equipped with an external temperature sensor. The tempera-
ture sensor is attachable. If so, the charger will compensate voltage accor-
ding to ambient temperature. Activated temperature sensor will be indicated
by a lit temperature sensor indicator lamp.
WARNING!
The spark protection on the battery charger
is disabled during SUPPLY program.
POWER LAMP
If the power lamp is lit with a:
1. STEADY LIGHT
The mains cable is connected to the wall socket.
2. FLASHING LIGHT:
The charger has entered the energy save mode. This happens if the
charger isn´t connected to the battery in 2 minutes.
20014905E MXS 10, Manual EU, Print file 004.indd 4 2011-10-11 08:50:50

Produkt Specifikationer

Mærke: Ctek
Kategori: Batterioplader
Model: MXS 10.0

Har du brug for hjælp?

Hvis du har brug for hjælp til Ctek MXS 10.0 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Batterioplader Ctek Manualer

Ctek

Ctek READY AUTOMOTIVE Manual

2 September 2024
Ctek

Ctek MXS 5.0 CHECK Acculader Manual

23 August 2024
Ctek

Ctek MXS 5.0 POLAR Acculader Manual

23 August 2024
Ctek

Ctek MXS 5.0 Test and Charge Acculader Manual

23 August 2024
Ctek

Ctek PRO25SE Acculader Manual

22 August 2024
Ctek

Ctek MXTS70 Acculader Manual

22 August 2024
Ctek

Ctek MXT 14 Acculader Manual

22 August 2024
Ctek

Ctek MXS 3.8 Acculader Manual

22 August 2024
Ctek

Ctek Njord Go Acculader Manual

22 August 2024
Ctek

Ctek D250TS Acculader Manual

22 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Graphite

Graphite 58G002-1 Manual

14 Juni 2025
Champion

Champion 100594 Manual

14 Juni 2025
Schwaiger

Schwaiger LPBC0500 Manual

14 Juni 2025
Champion

Champion 100593 Manual

14 Juni 2025
Graphite

Graphite 58G085-1 Manual

13 Juni 2025
Venom

Venom VS2872 Manual

9 Juni 2025
Stalco

Stalco Perfect BCP60-8ACS Manual

9 Juni 2025
Stalco

Stalco Perfect BCP60-5.5A Manual

8 Juni 2025
Xline

Xline CC702 Manual

8 Juni 2025
Draper

Draper D20 92239 Manual

8 Juni 2025