Ctek MXT 14 Manual

Ctek Batterioplader MXT 14

Læs gratis den danske manual til Ctek MXT 14 (6 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Ctek MXT 14, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

EN • 3

CHARGING

1. Connect the charger to the battery.

2. Connect the charger to the wall socket. The power lamp will indicate that the mains

cable is connected to the wall socket. The error lamp will indicate if the battery clamps

are incorrectly connected. The reverse polarity protection will ensure that the battery

or charger will not be damaged.

3.Press the MODE-button to select charging program.

4. Follow the indication lamps through the charging process.

The battery is ready to start the engine when is lit.

The battery is fully charged when is lit.

5. Stop charging at any time by disconnecting the mains cable from the wall socket.

MANUAL

ABSORPTION, READY TO USE

ANALYSE

NORMAL

BAT TERY

PROGRAM

ERROR LAMP

RECOND

PROGRAM

SUPPLY

PROGRAM

POWER

LAMP

MODE-

BUTTON

DESULPHATION

SOFT START

BULK FLOAT, FULLY CHARGED

PULSE, MAINTENANCE CHARGING

TEMPERATURE

SENSOR

INDICATOR

24V/14A

MXT 14

MODE

SUPPLYNORMAL RECOND

RECOND

SUPPLY

24V/14A

MXT 14

MODE

SUPPLYNORMAL RECOND

RECOND

SUPPLY

SUPPLY PLUG*

L: 2000 mm

TEMPERATURE

SENSOR

CONGRATULATIONS

to the purchase of your new professional switch mode battery

charger. This charger is included in a series of professional

chargers from CTEK SWEDEN AB and represents the latest

technology in battery charging.

MAINS CABLE

*Supply plugs may differ to suit your wall socket.

20015551E MXT 14, Manual EU, Print file 001.indd 3 2013-07-23 11:31:02

4 • EN

BATTERY SIZE (Ah) TIME TO 80% CHARGED

30Ah 2h

100Ah 6h

200Ah 12h

300Ah 17h

READY TO USE

The table shows the estimated time for empty battery to 80% charge

CHARGING PROGRAMS

Settings are made by pressing the MODE-button. After about two seconds the charger

activates the selected program. The selected program will be restarted next time the

charger is connected.

The table explains the different Charging Programs:

Program Battery

Size (Ah) Explanation Temp range

NORMAL 28–500Ah

Normal battery program

28.8V/14A. Use for WET batteries,

Ca/Ca, MF and for most GEL batteries

+5°C–+50°C

(41ºF–122ºF)

RECOND 28–500Ah

Recond program 31.6V/1.5A

Use to return energy to the empty

WET and Ca/Ca batteries. Recond

your battery once per year and after

deep dischare to maximise lifetime and

capacity. The Recond program adds the

Recond step to the normal battery

program. Frequent use of the Recond

program may cause water loss in the

batteries and reduce service life of

electronics. Contact your vehicle and

battery supplier for advice.

-20°C–+50°C

(-4ºF–122ºF)

28–500Ah

Supply program 27.2V/14A

Use as 24V power supply or use for

float maintenance charging when 100%

capacity of the battery is required.

Supply program activates Float step

without time or voltage limitation.

-20°C–+50°C

(-4ºF–122ºF)

ERROR LAMP

If the error lamp is lit, check the following:

1. Is the chargers positive lead connected to the batterys

positive pole?

2. Is the charger connected to a 24V battery?

3. Has charging been interrupted in or ?

Restart the charger by pressing the MODE-button. If charging is still

being interrupted, the battery...

...is seriosly sulphated and may need to be replaced.

...can not accept charge and may need to be replaced.

...can not keep charge and may need to be replaced.

WARNING!

The spark protection on the battery charger

is disabled during SUPPLY program.

TEMPERATURE SENSOR

The MXT 14 is equipped with an external temperature sensor. Activated

temperature sensor will be indicated by a lit temperature sensor indicator

lamp. The temperature sensor will adjust the voltage to the ambient

temperature. Place the temperature sensor in the positive clamp or as the

close to the battery as possible.

POWER LAMP

If the power lamp is lit with a:

1. STEADY LIGHT

The mains cable is connected to the wall socket.

2. FLASHING LIGHT:

The charger has entered the energy save mode. This happens if the

charger isn´t connected to the battery in 2 minutes.

20015551E MXT 14, Manual EU, Print file 001.indd 4 2013-07-23 11:31:03

Produkt Specifikationer

Mærke:	Ctek
Kategori:	Batterioplader
Model:	MXT 14
Bredde:	130 mm
Dybde:	235 mm
Højde:	65 mm
Vægt:	1900 g
Produktfarve:	Blue, Silver
Batterispænding:	2 V
Driftstemperatur (T-T):	-20 - 50 °C
Indgangsspænding:	220-240 V
Indgangsfrekvens:	50/60 Hz
Kabelfarve:	Sort
Aktuel opladning:	14