Ctek XS 0.8 Manual

Ctek Batterioplader XS 0.8

Læs gratis den danske manual til Ctek XS 0.8 (5 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Ctek XS 0.8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

EN • 3

ERROR LAMP

FULLY CH GEDARREADY TO USE

POWER LAMP

CHARGING

1. Connect the charger to the battery.

2. Connect the charger to the wall socket. The power lamp will indicate that the mains

cable is connected to the wall socket. The error lamp will indicate if the battery clamps

are incorrectly connected. The reverse polarity protection will ensure that the battery

or charger will not be damaged.

3. Follow the 6-step display through the charging process.

The the engine battery is ready to start 3 when STEP is lit.

The when battery is fully charged 5 STEP is lit.

4. Stop charging at any time by disconnecting the mains cable from the wall socket.

C GON RATULATIONS

to the purchase of your new professional switch mode battery charger. This charger is

included in a series of professional chargers from CTEK SWEDEN AB and represents the

latest technology in battery charging.

CTEK COMFORT CONNECT – eyelet M6

12V/0.8A

XS 0.8

CTEK COMFORT CONNECT

MAINS CABLE

CTEK COMFORT CONNECT – clamp

CHARGE CABLE

SUPPLY PLUG*

*Supply plugs may differ to suit your wall socket.

MANUAL

20014896E XS 0.8, Manual EU, Print le 003.indd 3 2011-10-10 16:25:43

4 • EN

BATTERY SIZE (Ah) TIME TO 80% CHARGED

2Ah 2h

8Ah 8h

20Ah 20h

32Ah 32h

READY TO EUS

The table shows the estimated time for empty battery to 80% charge

ERROR LAMP

If the error lamp is lit, check the following:

1. Is the chargers positive lead connected to the

batterys positive pole?

2. Is the charger connected to a 12V battery?

3. Has charging been interrupted in EP 1 or step 4? ST

Restart the charger. If charging is still being interrupted, the battery…

STEP 1: …is seriously sulphated and may need to be replaced.

STEP 4: …can not keep charge and may need to be replaced.

TE NICAL SPECIFICATIONSCH

Charger model XS 0.8

Model number 1047

Rated Voltage AC 220–240VAC, 50–60Hz

Charging voltage 14.4V

Start voltage 2.0V

Charging current 0.8A max

Current, mains 0.2A rms (at full charging current)

Back current drain* <1Ah/month

Ripple** <4%

Ambient

temperature

-20°C to +50°C, output power is reduced

automatically at high temperatures

Charger type Six step, fully automatic charging cycle

Battery types All types of 12V lead-acid batteries

(WET, MF, Ca/Ca, AGM and GEL)

Battery capacity 1.2―32Ah up to 100Ah for maintenance

Dimensions 145 x x x W x 55 38mm (L H)

Insulation class IP65

Weight 0.4kg

*) Back current drain is the current that drains the battery if the charger is not connected

to the mains. back a CTEK chargers has very low current.

**) The quality of the charging voltage and charging A current is very important. high

curre nt ripple heats up the battery which has an aging eﬀect on the positive electrode.

High voltage ripple could harm other equipment the that is connected to battery. CTEK

battery chargers produce very clean voltage and current with low ripple.

POWER LAMP

If the power lamp is lit with a:

1. STEADY LIGHT

The mains cable is connected to the wall socket.

2. FLASHING LIGHT:

The charger has entered the energy save mode. This happens if the

charger isn´t connected to the battery in 2 minutes.

20014896E XS 0.8, Manual EU, Print le 003.indd 4 2011-10-10 16:25:44

Produkt Specifikationer

Mærke:	Ctek
Kategori:	Batterioplader
Model:	XS 0.8
Bredde:	55 mm
Dybde:	145 mm
Højde:	38 mm
Vægt:	400 g
Produktfarve:	Sort, sølv
Batterispænding:	12 V
Driftstemperatur (T-T):	-20 - 50 °C
Indgangsspænding:	220-240 V
Indgangsfrekvens:	50/60 Hz
Kabelfarve:	Sort
Aktuel opladning:	0.8