Cuisinart SmartPower Bar Basics CB-18BKSS Manual

Cuisinart Blender SmartPower Bar Basics CB-18BKSS

Læs gratis den danske manual til Cuisinart SmartPower Bar Basics CB-18BKSS (24 sider) i kategorien Blender. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Cuisinart SmartPower Bar Basics CB-18BKSS, eller vil du spørge andre brugere om produktet?

Side 1/24
SmartPower Bar Basics18-Speed Blender
INSTRUCTION AND
RECIPE BOOKLET
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
CB-18BKSS
2
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety precautions should always
be followed, including the following:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. To protect against the risk of electrical shock, do not put motor
base of blender in water or other liquid.
3. Close supervision is necessary when any appliance is used by
or near children.
4. Unplug from outlet when not in use, before putting on or taking
off parts, and before cleaning or removing contents from
blender jar. Never put hands into the blender jar or
container, or handle the blades with appliance plugged in.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or is dropped or damaged in
any manner. Return appliance to nearest Cuisinart service
facility for examination, repair, and/or mechanical or electrical
adjustment.
7. The use of attachments, including canning or ordinary jars, not
recommended or sold by Cuisinart may cause fire, electrical
shock, or risk of injury to persons.
8. Do not use outdoors.
9. Do not let cord hang over edge of counter or table or touch
hot surfaces.
10. Keep hands and utensils out of jar while blending, to
reduce the risk of severe injury to persons or damage to
blender itself. A rubber or plastic spatula may be used but
must be used only when the blender is turned OFF.
11. When blender is in ON mode, and LED lights are flashing or
glowing, do not touch cutting assembly, interfere with blade
movement, or remove blender jar cover. Accidentally touching
a speed button may activate the blender.
12. BLADES ARE SHARP. HANDLE CAREFULLY.
13. To reduce the risk of injury, never place cutting assembly on
base unless the blender jar is properly attached.
14. Always operate blender with the cover in place.
15. Never leave your blender unattended while running.
16. When blending HOT liquids, remove measured pour lid (center piece of
cover) to allow steam to escape.
17. Twist on locking ring firmly. Injury can result if moving blades
accidentally become exposed.
18. Do not use an extension cord with this unit. Doing so may result in fire,
electrical shock, or personal injury.
Regarding your cord set: A longer cord has been provided so that
you will have flexibility in positioning your Cuisinart®SmartPower Bar
Basics™ 18-Speed Blender near an electrical outlet. Exercise care
when using the longer cord, to avoid entangling or tripping over the
cord. The longer cord should be arranged so that it will not drape over
the counter or tabletop, where it can be pulled on by children or tripped
over. Excess cord should be stored in the cord storage area at the back
of the blender base to avoid injury caused by the longer cord.
19. Wash the blender jar, cutting assembly, locking ring, and cover before
first use.
20. WARNING: TO REDUCE THE RISK OF ELECTRICAL SHOCK OR
FIRE, DO NOT REMOVE THE BASE PANEL. NO USER SERVICE-
ABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE ONLY BY
AUTHORIZED PERSONNEL.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
NOTICE:
This appliance has a polarized plug (one prong is wider than the other).
To reduce the risk of electric shock, this plug will fit into a polarized outlet
only one way. If the plug does not fit fully into the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician. Do not modify the plug
in any way.
3
UNPACKING INSTRUCTIONS
1. Place the gift box containing your Cuisinart®SmartPower Bar
Basics™ 18-Speed Blender on a flat, sturdy surface before unpacking.
2. Remove instruction booklet and other printed materials from top
of corrugated insert. Next remove the top corrugated insert.
3. Carefully lift blender jar assembly from box and set aside. Be careful
not to tip the jar when removing.
4. Remove the lower corrugated insert containing the blender base.
5. Remove any additional literature from the box.
To assemble the blender, follow the Assembly instructions on page 4 of this
instruction booklet. Replace all corrugated inserts in the box and save the
box for repackaging.
Before using for the first time: Wash all parts according to the Cleaning
and Maintenance section on page 6 of this booklet to remove any dust
or residue.
TABLE OF CONTENTS
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Helpful Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Easy Reference Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6
Dos and Don’ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
Recipe Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
Recipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 21
INTRODUCTION
Get ready to blend bigger batches than ever! Your Cuisinart
®SmartPower
Bar Basics™ 18-Speed Blender comes with a 50 oz. stainless steel jar that
holds more ... and won’t break. We’ve engineered this big blender with 18
precision speeds and a separate ice crush button to give you unlimited
blending options. Since it’s from Cuisinart, it’s easy to use and even easier
to clean.
Have fun and ... happy blending!
4
FEATURES AND BENEFITS
1. Cover
Just press on. Tightfitting
seal resists leakage.
2. 2-oz. Measured Pour Lid
Allows you to measure
and add ingredients
without removing the
cover.
3. 50-oz. Stainless
Steel Jar
This unbreakable
stainless steel jar has
easy-to-read graduation
marks.
4. Leak-proof Rubber
Gasket (not shown)
Holds the glass jar
snugly in position for safe
operation.
5. High-quality Cutting
Assembly with Patented
Stainless Steel Blades
Is strong enough for all
blender tasks, including
tough jobs, from ice
crushing to chopping
delicate herbs.
Note: Blades are sharp handle carefully.
6. Locking Ring
Is self-aligning so that the glass blender jar slides easily into position.
7. Heavy-duty Motor Base
Is so sturdy and stable, it will not “walk” on your counter even during
ice crushing!
8. 18-Speed Dial with Push-button Controls
a. 18-Speed Dial Control
Choose from 18 speeds to blend ingredients to the desired
consistency.
b. Pulse Button
Set the dial to the desired speed and press the Pulse button. Pulse
at any speed to blend ingredients only as much as needed.
c. Ice Crush Button
Press the ice crush button to begin crushing. This button is preset to
the best speed for crushing ice.
9. Slip-proof Feet
Prevent movement during use and prevent damaging marks on
countertops or tables.
10. Cord Storage (not shown)
Keeps countertop safe and neat by conveniently storing excess cord.
USE AND CARE
ASSEMBLY
To use your Cuisinart®SmartPower Bar
Basics™ Blender, begin by assembling
the blender jar.
1. Turn the blender jar (a) upside down, and
place it flat on a sturdy
surface.
2. Position the rubber gasket (b) on
the round opening on the bottom
of the blender jar.
3. Turn the cutting assembly (c)
upside down, and place the blade
end in the blender jar opening.
Note: Blades are sharp handle carefully.
4. Secure the rubber gasket and cutting assembly into position by
placing the smaller opening of the locking ring (d) on top of the cutting
assembly. Engage threads by twisting the locking ring clockwise until
tightened. Make sure locking ring is tightly fastened to blender jar.
Once assembled, turn the blender jar right side up.
5. Push the cover onto the top of the blender jar. Push the measured pour
lid into the cover.
6. Place blender jar on the motor base so that the jar markings are facing
you and the handle is positioned to one side.
7. Plug in power cord. Your blender is now ready to be used.
(d)
(b)
1.
2.
3.
5.
6.
7.
8.
9.
8b.
8c.
8a.
(c)
(a)
5
HELPFUL REMINDERS
Once the cover is in position, additional ingredients can be added
during blending by simply lifting the measured pour lid, adding
ingredients, and replacing the measured pour lid.
Cover should always be in place while the unit is on.
Warning: Do not place blender jar onto base while motor is running.
Do not twist locking ring off blender jar when removing blender jar from
base. Simply lift blender jar from motor base.
Follow Cleaning and Maintenance instructions on page 6, prior to your
first use.
OPERATION
1. Place the motor base of your Cuisinart®SmartPower Bar Basics™
Blender onto a flat, sturdy surface. It is important that the surface
be clean and dry. Assemble the blender by following the assembly
instructions. Once the jar is assembled and is in position on the motor
base, plug the Cuisinart®SmartPower Bar Basics™ Blender into an
electrical outlet.
2. Add all necessary ingredients to the blender jar, and replace the cover.
You may add more ingredients by lifting the measured pour lid and
dropping ingredients through the fill area. Replace the measured pour
lid after adding ingredients. Do not place hands into blender jar with
blender plugged in.
Note: Add liquid ingredients first, then follow with solid ingredients.
This will provide more consistent blending and prevent unnecessary stress
on the motor.
Note: To remove blender jar cover, lift edge of cover upwards. Lifting
measured pour lid will not remove cover.
3. TO START BLENDING: Choose a speed for blending your ingredients.
Press the ON button for continuous blending. The LED light will
illuminate when the blender is on.
4. TO STOP BLENDING: To stop the blending process, push the
OFF button.
5. PULSE MODE: The pulse mode allows you to create a burst
of power for quick, efficient blending. To use the pulse function, choose
a speed for blending your ingredients. Push and release the PULSE
button. Repeat as desired. You determine the duration of each pulse.
QUICK REFERENCE GUIDE
To Activate Blender Press ON- The blender is in ON mode.
To Begin Blending Press desired speed button.
To Change Speeds Press desired speed button.
To Pulse
In ON mode press PULSE, then press and
release desired speed button as needed.
To Crush Ice In ON mode, press and release
ICE CRUSH button as needed.
To Stop Blending Press OFF button.
(and Deactivate Blender)
To Stop Blending Release button.
(in Pulse or Ice Crush Mode)
SPEED SELECTION GUIDE
Refer to this guide to choose the best speed for your desired result.
Ingredient/Recipe Speed Result
Reconstituting frozen juice 8-12 Smooth and full-bodied
concentrates
Mayonnaise 10-12 Thick and Creamy
Salad dressings 10-14 Completely blended and
emulsified
Nuts (shelled, 1/2 cup or less 2-6 Coarse to fine
at a time) pulse to chop
Heavy or whipping cream 2-pulse Thick creamy topping
Bread, Cookies or Crackers 12-pulse/blend Coarse to fine as
(1/2-inch pieces, 1 cup or desired
less at a time)
Grating/chopping citrus zest 12-pulse/blend Uniformly fine
(add 1-2 tsp. Sugar or salt
from recipe)
Smoothies, shakes, health drinks 14-18 Smooth, creamy and thick
Baby foods/fruit and vegetable 14-16 Smooth and creamy
purées
Frozen cocktails 16 -18 Thick and slushy
Hard cheeses 12-pulse/blend Coarse to fine
Spices 12-18 Coarse to fine
pulse/blend
Ice Ice Crush, Coarse crush to snowy
pulse or
continuous
7
DOS AND DON’TS WHEN USING
YOUR BLENDER
DO:
Make sure the electrical outlet is rated at the same voltage as that
stated on the bottom of the blender motor base.
Always use the blender on a clean, sturdy and dry surface.
Always add liquid ingredients to the blender jar first, then add remaining
ingredients. This will ensure that ingredients are uniformly mixed.
Cut most foods into approximately 12inch (1.3 cm) to 1 inch (2.5 cm)
cubes to achieve a more uniform result. Cut all cheeses into pieces no
larger than 12inch (1.3 cm).
Use the measured pour lid to measure liquid ingredients such as
alcohol. Replace measured pour lid after ingredients have been added.
Use a rubber or plastic spatula as needed, only when the blender
is turned off. Never use metal utensils, as damage may occur to
the blender jar or cutting assembly.
Place cover on firmly. Always operate the blender with the
cover on.
Make sure locking ring is tightly attached to blender jar.
Always remove locking ring, cutting assembly, and rubber gasket
before cleaning.
When scraping the blender jar with a spatula, remove the food from the
sides of the blender jar and place food in the center of the blender jar,
over the cutting assembly.
When chopping fresh herbs, garlic, onion, zest, bread crumbs, nuts,
spices, etc, make sure the blender jar and cutting assembly are
completely dry.
If food tends to stick to the sides of the blender jar when blending, pulse
in short bursts.
Pulses should be short bursts. Space the pulses so the blades stop
rotating between pulses.
DON’T:
Don’t store food or liquids in your blender jar.
Don’t place cutting assembly and locking ring onto motor base without
the blender jar attached.
Don’t attempt to mash potatoes, knead heavy dough, or beat
egg whites.
Don’t remove blender jar while unit is on. Keep the blender jar cover on
the blender jar while blending.
Don't twist locking ring from blender jar when removing blender jar from
motor base. Simply lift blender jar from motor base.
Don’t overprocess foods. Blender will achieve most desired results in
seconds, not minutes.
Don’t overload blender. If the motor stalls, turn the blender off
immediately, unplug the unit, and remove a portion of the food,
then continue.
Don’t use any utensil inside the blender jar while the motor is on.
Don’t use any container or accessories not recommended by Cuisinart.
Doing so may result in injury.
Don’t place hands inside the blender jar when blender is plugged in.


Produkt Specifikationer

Mærke: Cuisinart
Kategori: Blender
Model: SmartPower Bar Basics CB-18BKSS

Har du brug for hjælp?

Hvis du har brug for hjælp til Cuisinart SmartPower Bar Basics CB-18BKSS stil et spørgsmål nedenfor, og andre brugere vil svare dig