CyberData Systems 011180 Manual

CyberData Systems Højttaler 011180

Læs gratis den danske manual til CyberData Systems 011180 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9 anmeldelser. Har du et spørgsmål om CyberData Systems 011180, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Quick Start Guide 930466A

The IP Endpo int Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/ceilingspkr2ptt/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP V2 Ceiling Speaker, Push-to-Talk,

Quick Start Guide

Quick Start Guide 930466A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN power/status LED and the YELLOW network LED come on

immediately. The YELLOW network LED will blink to indicate network

traffic. After about 27 seconds, the GREEN power/status LED will blink

twice to indicate that the board is fully booted.

If there is no DHCP server available on the network, it will try 12 times with

a three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold the

RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Speaker

Status

(Green LED)

Network

Link/Activity

(Yellow LED)

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Højttaler
Model:	011180

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems 011180 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler CyberData Systems Manualer

CyberData Systems SIP 011393 Manual

31 August 2024

CyberData Systems Singlewire 011182 Manual

31 August 2024

CyberData Systems SIP-enabled IP V2 Manual

31 August 2024

CyberData Systems SIP IP66 Manual

31 August 2024

CyberData Systems 11394 Manual

27 August 2024

CyberData Systems 011520 Manual

27 August 2024

CyberData Systems 011180 Manual

27 August 2024

CyberData Systems 011487 Manual

27 August 2024

CyberData Systems InformaCast Manual

27 August 2024

CyberData Systems 011181 Manual

27 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Edifier MP330 Manual

15 Juni 2025

Hecate G1500 Manual

14 Juni 2025

XLEADER SoundAngel A8 Manual

14 Juni 2025

RCF DU 31EN Manual

14 Juni 2025

Omnitronic PS-2.5WB Manual

14 Juni 2025

Greadio R-919 Manual

14 Juni 2025

J.W. SPEAKER 8700 Evolution J2 Manual

14 Juni 2025

SpringFlora HM11 Manual

14 Juni 2025

Fiodio F-130 Manual

14 Juni 2025

HEYSONG Bubble Manual

14 Juni 2025