CyberData Systems Singlewire 011182 Manual

CyberData Systems Højttaler Singlewire 011182

Læs gratis den danske manual til CyberData Systems Singlewire 011182 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om CyberData Systems Singlewire 011182, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick Start Guide 930465A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide, which is available on the

Documentation page at the following website address:

http://www.cyberdata.net/products/voip/digitalanalog/singlewirespeakerptt/docs.html

2.0 Select Power Source

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of the device. See the

following figure:

3.2. The GREEN power/status LED and the YELLOW network LED come on immediately. The

YELLOW network LED will blink to indicate network traffic. After about 27 seconds, the GREEN

power/status LED will blink twice to indicate that the board is fully booted.

This concludes the power test.

PoE Switch PoE Injector

Set PoE power type to IEEE 802.3af

Power Class 0 (15.4W)a

a. When initiating the device for the first time, we recommend manually adjusting the PoE switch port power

setting to Class 3 to ensure sufficient power allocation. Once the initial setup has been completed and the

device is SIP enabled, the Administrator may prefer a final power setting adjustment to Class 0.

CAT6 cable recommended—for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

Speaker

Status

(Green LED)

Network

Link/Activity

(Yellow LED)

The IP Endpoint Company

V2 Speaker, Push-to-Talk, Singlewire

Quick Start Guide

Quick Start Guide 930465A

4.0 InformaCast Configuration File Retrieval

4.1. DHCP should be enabled. After the speaker initializes, it will send a broadcast to the DHCP server

to ask for the location of its InformaCastSpeaker.cfg configuration file.

4.2. SLP or TFTP?

•SLP should be enabled on InformaCast version 5.0.4 or higher. SLP is an InformaCast protocol

introduced in InformaCast version 5.0.4. The speaker will retrieve its configuration file from an

InformaCast server folder specified by SLP. SLP method is preferred.

•TFTP servers may be used instead of SLP. In this alternate scenario, DHCP option 150 is required to

provide the speaker with the address of the TFTP server. Otherwise, the speaker will be unable to

retrieve its configuration file.

Note The CyberData V2 Ceiling Speaker and InformaCast server should be on the same subnet

during the speaker's initial configuration if it cannot access the VLANs upon which the

InformaCast Server and DHCP servers are located.

5.0 Singlewire-Enabled V2 Ceiling Speaker Identification and Testing

5.1. Ensure the InformaCast Server has detected a new speaker.

5.2. Test the newly detected speaker.

5.3. Add the newly detected speaker to the InformaCast Server.

6.0 Contacting CyberData VoIP Technical Support

For quality assurance purposes, we ask that you please visit our website and complete our Support form

which is available at the following website address:

http://w ww.cybe rdata.net/support/contac tsupportvoip .html

The Support form initiates a ticket which CyberData uses for tracking customer requests. Most

importantly, the Support form provides us with pertinent troubleshooting information. Please include as

much detail as possible in the Comments section of the Support form.

Be prepared to provide a Wireshark capture of the speaker's boot process and ensure you have properly

mirrored the speaker's switch port.

Requests for Returned Materials Authorization (RMA) numbers require an active VoIP Technical Support

ticket number.

If you have purchased a Singlewire-Enabled V2 Ceiling Speaker in error, please immediately contact your

authorized distributor or reseller for exchange. CyberData Corporation offers repair services under the

Manufacturer's Limited 2 Year Warranty but is unable to offer exchanges.

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Højttaler
Model:	Singlewire 011182

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems Singlewire 011182 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler CyberData Systems Manualer

CyberData Systems SIP 011393 Manual

31 August 2024

CyberData Systems Singlewire 011182 Manual

31 August 2024

CyberData Systems SIP-enabled IP V2 Manual

31 August 2024

CyberData Systems SIP IP66 Manual

31 August 2024

CyberData Systems 11394 Manual

27 August 2024

CyberData Systems 011520 Manual

27 August 2024

CyberData Systems 011180 Manual

27 August 2024

CyberData Systems 011487 Manual

27 August 2024

CyberData Systems InformaCast Manual

27 August 2024

CyberData Systems 011181 Manual

27 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Muse M-968 BTY Manual

1 August 2025

Grundig Portable 360 Manual

1 August 2025

Grundig Band 360 Manual

1 August 2025

Grundig GBT Connect 360 Manual

1 August 2025

Muse M-968 BTR Manual

31 Juli 2025

JLab Epic Party Manual

31 Juli 2025

JVC XS-E423 Manual

30 Juli 2025

SoundTube RF31-EZ-T Manual

30 Juli 2025

Valcom VIP-480AL-W-SA Manual

30 Juli 2025

Rockustics StoneHenge II-S/T Manual

30 Juli 2025