CyberData Systems SIP Paging Adapter Manual

CyberData Systems Telefon SIP Paging Adapter

Læs gratis den danske manual til CyberData Systems SIP Paging Adapter (4 sider) i kategorien Telefon. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 29 anmeldelser. Har du et spørgsmål om CyberData Systems SIP Paging Adapter, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Quick Start Guide 931086B

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/voip/011233/

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

Part Number: 011233

SIP Paging Adapter

Quick Start Guide

Quick Start Guide 931086B

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN/BLUE Status LED and the GREEN Paging LED both blink at a

rate of 10 times per second during the initial network setup.

The round, GREEN/BLUE Status LED on the front of the Paging Server

comes on indicating that the power is on. Once the device has been

initialized, this LED blinks at one second intervals.

The square, GREEN/AMBER Link LED above the Ethernet port indicates

that the network connection has been established. The Link LED changes

color to confirm the auto-negotiated connection speed:

• The Link LED is GREEN at 10 Mbps.

• The Link LED is AMBER at 100 Mbps.

The GREEN Paging LED comes on while the device is booting and turns off

after 15 seconds. This light blinks when a page is in progress.

You can disable

Beep on Initialization on the Device Configuration page.

The square, GREEN Activity LED blinks when there is network traffic.

If there is no DHCP server available on the network, it will try 12 times with a

three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, briefly press and

then quickly release the RTFM switch to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Status

(GREEN/BLUE LED)

Paging

(GREEN LED)

Link

(GREEN/AMBER LED)

Activity

(GREEN LED)

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Telefon
Model:	SIP Paging Adapter

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems SIP Paging Adapter stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telefon CyberData Systems Manualer

CyberData Systems SIP Paging Adapter Manual

31 August 2024

CyberData Systems 011462 Manual

27 August 2024

CyberData Systems 011461 Manual

27 August 2024

CyberData Systems 011460 Manual

27 August 2024

Telefon Manualer

Nyeste Telefon Manualer

Alcatel Temporis SP2604G Manual

10 Juni 2025

Panasonic KX-TGC212 Manual

9 Juni 2025

Panasonic KX-TG8051 Manual

6 Juni 2025

Siemens Gigaset E500 Manual

2 Juni 2025

Gigaset E290M Manual

9 April 2025

Bogen MCDS4 Manual

1 Marts 2025

Bogen CA15C Manual

1 Marts 2025

Ubiquiti Networks G3 Touch Enterprise Manual

25 Februar 2025

POCO X3 GT Manual

22 Februar 2025

POCO M4 Pro 5G Manual

22 Februar 2025