CyberData Systems 011462 Manual

CyberData Systems Telefon 011462

Læs gratis den danske manual til CyberData Systems 011462 (3 sider) i kategorien Telefon. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18 anmeldelser. Har du et spørgsmål om CyberData Systems 011462, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Quick Start Guide 931484A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available in the Downloads tab at the following webpage:

http://www.cyberdata.net/voip/011462/

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100Mbps

3 4

Part Number: 011462

SIP Armored Steel Ringdown Phone

Quick Start Guide

The IP Endpoint Company

Quick Start Guide 931484A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the board. See the following figure:

3.2. The amber 100 Mb Link LED blinks off once during the boot up process

when the device begins DHCP addressing and autoprovisioning attempts,

and then comes on again and remains constant (solid amber). The green

Link/Activity LED may be blinking depending on the network activity.

Note The default DHCP addressing timeout is 60 seconds. The device will attempt

DHCP addressing 12 times with a 3 second delay between tries and eventually

fall back to the programmed static IP address (by default 10.10.10.10) if DHCP

addressing fails. The DHCP Timeout is configurable in the device's Network

settings.

3.3. When the device has completed the initialization process, press and hold

the RESET switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

100 Mb Link LED

Link/Activity J1

Produkt Specifikationer

Mærke:	CyberData Systems
Kategori:	Telefon
Model:	011462

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberData Systems 011462 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Telefon CyberData Systems Manualer

CyberData Systems SIP Paging Adapter Manual

31 August 2024

CyberData Systems 011462 Manual

27 August 2024

CyberData Systems 011461 Manual

27 August 2024

CyberData Systems 011460 Manual

27 August 2024

Telefon Manualer

Nyeste Telefon Manualer

Alcatel Temporis SP2604G Manual

10 Juni 2025

Panasonic KX-TGC212 Manual

9 Juni 2025

Panasonic KX-TG8051 Manual

6 Juni 2025

Siemens Gigaset E500 Manual

2 Juni 2025

Gigaset E290M Manual

9 April 2025

Bogen MCDS4 Manual

1 Marts 2025

Bogen CA15C Manual

1 Marts 2025

Ubiquiti Networks G3 Touch Enterprise Manual

25 Februar 2025

POCO X3 GT Manual

22 Februar 2025

POCO M4 Pro 5G Manual

22 Februar 2025