CyberPower UT650EG Manual

CyberPower UPS UT650EG

Læs gratis den danske manual til CyberPower UT650EG (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om CyberPower UT650EG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

UT650EG / UT800EG / UT1050EG

User’s Manual

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual

thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the

specifications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit near

heat emitting appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized

personnel away from batteries.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following: (1) UPS Unit x1; (2) User Manual x1

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is recommended to ensure that the battery's

maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC

outlet. The unit will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage device (Zip drive, Jazz drive, Tape drive, etc.

into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device into the

battery power supplied outlets. The power demands of these devices will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not

service equipment with large electrical demands (e.g. air conditioner, refrigerator, copier, etc. Avoid using extension cords.

4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will "beep".

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at least one piece of

equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker / fuse is normal and then turns the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery life.

BASIC OPERATION

1. Power Switch

Press the switch for 2 seconds to turn the UPS ON or OFF.

Alarm setting: The audible alarm can be turned OFF or ON by quickly pressing the POWER button twice. The default setting is for the Alarm On.

To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps when the Alarm is turned off. To turn the Alarm back on,

quickly press the power button twice. You will hear a single short beep

when the Alarm is turned on.

2. LED Indicators

The LED indicates the status of UPS. Refer to Definitions for

Illuminated LED Indicators section for details.

3. AC Outlet

The UPS provides power for connected equipment to insure temporary

uninterrupted operation during a power failure and against surges and spikes.

4. Replaceable Fuse / Circuit Breaker

The fuse or circuit breaker provides overload protection.

5. Input Power Cord

Connect to utility power.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

LED Light Audible Alarm UPS Status Description

Green ON - ECO Mode The utility is normal. The UPS operates in

energy-saving mode.

Slowly Flashing - Charging The utility is normal. The UPS is charging the battery.

Yellow ON Beep twice every 30 seconds Battery Mode The UPS is providing battery power.

Flash Rapid Beeping Low Battery The UPS will run out of battery power soon.

Red

ON, Flash once

every 5 seconds Constant Tone Battery Output Short Fault Turn off the UPS and unplug at least one piece of

equipment.

ON, Flash twice

every 5 seconds Constant Tone Overload Fault

Connected equipment exceeds the rating of the unit.

Turn off the UPS and unplug at least one piece of

equipment.

ON, Flash 3 times

every 5 seconds Constant Tone Charger Fault Contact CyberPower for support

ON, Flash 4 times

every 5 seconds Constant Tone Hardware Fault Contact CyberPower for support

Flash Constant Tone Overload Warning

Connected equipment exceeds the rating of the unit.

Turn off the UPS and unplug at least one piece of

equipment.

TECHNICAL SPECIFICATIONS

TROUBLESHOOTING

Problem Possible Cause Solution

The UPS does not perform

expected runtime.

Batteries are not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is slightly worn out. Contact CyberPower Systems Technical Support.

The UPS will not turn on.

The unit is not connected to an AC outlet. The unit must be connected to a 220-240V outlet.

The battery is worn out. Contact CyberPower Systems Technical Support.

Mechanical problem. Contact CyberPower Systems Technical Support.

Outlets do not provide

power to equipment.

Fuse is blown or breaker is tripped due to

overload.

Turn the UPS off and unplug at least one piece connected equipment. Unplug

the power cord of the UPS then replace the blown fuse with a spare one or

press the circuit breaker knob. Connect power cord then turn the UPS on.

Make sure that your spare fuse meets the specification.

Batteries are discharged. Allow the unit to recharge for at least 4 hours.

Unit has been damaged by a surge or

spike. Contact CyberPower Systems Technical Support.

For more information, visit www.cyberpower.com

Model UT650EG UT800EG UT1050EG

Capacity (VA/W) 650/360 800/400 1050/630

Input

Voltage Range 165~290Vac

Nominal Frequency 50/60Hz +/-5Hz

Output

On Battery Output Voltage 220/230/240Vac

On Battery Output Frequency 50/60Hz +/-1%

Overload Protection Fuse Fuse Circuit Breaker

Physical

Total UPS Receptacles Universal x 3 Universal x 3 Universal x 4

Dimensions (W x H x D)(mm) 84 x 174 x 280 84 x 174 x 280 95 x 220 x 307

Weight 3.8 kg 4.0 kg 6.9 kg

Battery

Sealed Maintenance Free Lead Acid Battery RBP0119 p2-x1 RBP0143 p2-x1 RBP0119 p2-x2

Typical Recharge Time 6 Hours to 90% from total discharge

Warning Diagnostics

Indicators Utility / Battery / Fault

Audible Alarms On Battery, Low Battery, Overload, Fault

Environmental

Operating Temperature 0 C to 40 C  

Operating Relative Humidity 0 to 90%

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	UPS
Model:	UT650EG
Bredde:	84 mm
Dybde:	280 mm
Højde:	174 mm
Vægt:	3800 g
Produktfarve:	Sort
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Tower
Responstid:	4 ms
Opbevaringstemperatur (T-T):	-20 - 50 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 90 %
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Plast
Udgangseffekt:	360 W
Certificering:	CE
LED-indikatorer:	Ja
Kabellængde:	1.2 m
Opladningstid for batteri:	6 t
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 3000 m
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
AC udgange, antal:	3 AC stikkontakt(er)
AC stikkontakt typer:	Type F
Indgående driftsspænding (maks.):	290 V
Output strømkapacitet (VA):	0.65 kVA
Indgående driftsspænding (min.):	165 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	230 V
UPS topologi:	Interaktivt indgangsstik
Bølgeform:	Sine
Hørbare alarmtilstande:	Alarm when on battery, Fault, Low battery alarm, Overload alarm
Automatisk spændingsregulering (AVR):	Ja
EMI/RFI støjfiltrering:	Ja