Danfoss TP5000 RF Si Manual

Danfoss Termostat TP5000 RF Si

Læs gratis den danske manual til Danfoss TP5000 RF Si (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Danfoss TP5000 RF Si, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Fig.1

TP5000 Si/TP5000 RF Si

User Instructions

Mon-Fri Sat-Sun

Fig.2

Before programming the thermostat press and release the RESET button to restart

the unit. (Fig. 1)

Setting the Clock and Day

The day and time are set in the factory and therefore it will not normally be necessary

to do this on site. Changes between summer and winter time are handled automatically

by the unit.

Accepting the Factory Pre-settings

The TP5000 Si has pre-set times already programmed in, which often suit most people

(see table below).

Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per

day, events 2, 3, 4 & 5 are skipped and the events are re-numbered.

To adjust the factory pre-settings & set your own time and temperature

programmes

For Days 1-5 (weekdays)

a) Press PROG (Fig. 2) until the 1st pre-set time and temperature (Event 1 Days 1,2,3,4,5)

(Fig. 3).

b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min

increments).

c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.

d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).

e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.

For Days 6-7 (weekends)

Press •PROG (Fig. 2) to show 1st pre-set time and temperature (Event 1 Days 6-7)

(Fig. 7).

Repeat steps b, c and d above to programme time and temperature events for •

the weekend.

Returning to RUN mode

Press PROG (Fig. 2) – the colon in the LCD display will start to ﬂash (Fig. 8).

Fig.5

Fig.4

Fig.6

Fig.7

Fig.8

Event Time Temp. °C

1 06:30 20

2 08:30 15

3 11:30 20

4 13:30 15

5 16:30 21

6 22:30 15

Event Time Temp. °C

1 07:30 20

2 09:30 20

3 11:30 20

4 13:30 20

5 16:30 20

6 22:30 15

RESET

Fig.3

Complete Shut oﬀ - Summer time

Press Λ and V together to enter thermostat mode. A frost protection symbol (snowﬂake in a

shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display.

To return to automatic programming press both ∧ and ∨ together.

Danfoss Randall Ltd

Ampthill Road

Bedford, MK42 9ER

Tel: 0845 1217 400

Fax: 0845 1217 515

Email: danfossrandall@danfoss.com

Website: www.danfoss-randall.co.uk

Fig.10

Fig.11

Selection of time

or actual room

temperature in main

LCD display

Temporary

override of

programmed

temperature

press

together

Frost

Protection

Fig.9

Fig.12

Temporary User Overrides

The TP5000 has several useful overrides which can be selected without aﬀecting the

thermostat programming.

• Selection of time or actual room temperature in main LCD display – press +

and – together to change between settings (Fig. 9).

• Temporary override of programmed temperature – press Λ or V until required

temperature is displayed (override will automatically cancel at beginning of next

programmed event) (Fig. 10).

• Frost Protection – a constant low temperature can be selected whilst away from

home - press Λ and V together (Fig.11). Then use Λ or V to select the required

temperature. To return to automatic programming press Λ and V together again.

Battery Replacement

• Alowbattery symbol will ﬂash in the LCD display (Fig. 12)

You have 15 days to replace the battery before the unit will switch oﬀ. •

Remove old batteries and insert new ones. All settings including time are •

maintained.

Press and release the •RESET button to restart the unit. (Fig. 1)

NB. If the display ever goes blank during normal operation, the batteries will need

to be renewed with high quality alkaline cells. The reset button should be pressed

to restart the unit. All times, dates and events will be retained and need not be re-

programmed.

If the property is owned by a landlord he may, for gas safety reasons, have instructed the installer

to set the service interval timer.

If set a visual and audible warning will alert you that the boiler will need servicing within the next

28 days. This warning is repeated each day at noon. (Fig. 15)

If the boiler is not serviced within 28 days the daily audible warning will sound continuously and

can only be cancelled each day by pressing any button on the unit.

In addition, all overrides and programming buttons will be disabled and the heating and hot water

will only operate for 15 minutes in each programmed hour.

As this is a gas safety feature only an installer can reset the service interval timer. This will be done

as part of the boiler service as part of the boiler service.

Service Interval Timer

Fig. 15

Commissioning Instructions

If the thermostat and the receiver have been supplied together in a combined pack, the

units have been paired in the factory and no commissioning is required (RX1 only).

To tune the RX receiver to the frequency of the thermostat signal, follow steps 1-5 below.

Step 1

TP5000-RF Si - Reset the unit by pressing the recessed reset button.

Step 2

Press and hold V and + buttons (ﬁg. 13) for 3 seconds (TP5000 RF Si now transmits unique signal

continuously for 3 minutes).

Step 3

RX1 - Press and hold buttons PROG and CH1 for 3 seconds until green light ﬂashes once.

(Fig. 14)

Step 4 (Fig.14)

RX2 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 -perform steps 1-2 and then press PROG and CH2 on RX2.

RX3 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 - perform steps 1-2 and then press PROG and CH2 on RX3 then step 5.

Stat 3 - perform steps 1-2 and then press PROG and CH3 on RX3.

Step 5

TP5000Si-RF - Press V or Λ to select temperature - the unit will revert back to operating mode.

IMPORTANT RF Models only

To ensure that the factory programmes are set and the micro-computer is operating correctly

it is essential that you press and hold the RESET button before you begin any commissioning or

programming.

Fig.13

Fig.14

Produkt Specifikationer

Mærke:	Danfoss
Kategori:	Termostat
Model:	TP5000 RF Si

Har du brug for hjælp?

Hvis du har brug for hjælp til Danfoss TP5000 RF Si stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Danfoss Manualer

Danfoss React M30x1.5 Manual

1 Februar 2025

Danfoss React RA click Manual

1 Februar 2025

Danfoss HC6000 Thermostaat Manual

12 Januar 2025

Danfoss ORT-10 Manual

11 Januar 2025

Danfoss RA 2982 Manual

6 Oktober 2024

Danfoss TP5E-RF Manual

23 September 2024

Danfoss TP5 Manual

17 September 2024

Danfoss Ally - Radiator Thermostat Thermostaat Manual

1 September 2024

Danfoss TP5001Range gebruik Manual

25 August 2024

Danfoss RA 2000 series Manual

23 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Honeywell RTH21B Manual

14 Juni 2025

Tado Wireless Temperature Sensor X Manual

9 Juni 2025

Fantini Cosmi CH123E Manual

26 Marts 2025

Netatmo Smart Radiator Valve Manual

26 Februar 2025

Netatmo Smart Thermostat Manual

26 Februar 2025

5 Februar 2025

1 Februar 2025

29 Januar 2025

15 Januar 2025

Vaillant calorMatic VRT 370 Manual

15 Januar 2025