Dangerous Music Master Cutter Manual

Dangerous Music Processor Master Cutter

Læs gratis den danske manual til Dangerous Music Master Cutter (7 sider) i kategorien Processor. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Dangerous Music Master Cutter, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
The Dangerous Music Master
Setup and Operation manual
The Dangerous Music mastering transfer console represents the culmination of over 25
years of experience in the design and implementation of custom mastering equipment in
many of the world’s top mastering studios by the designers at DMI. This experience has
been distilled down to a two-rack space unit of exceptional ergonomic and sonic
performance. In conjunction with the Dangerous Music Monitor, the addition of one’s
favorite analog processing equipment and A/D/A converters, the Master makes the setup
of a world-class analog mastering system easier than it has ever been. This manual
explains the features, controls, connections, and suggestions for the operation of this unit.
Introduction 1
Safety Review 2
Overview 3
Rear panel connections 4
Front panel controls 5
Internal jumpers 6
Specifications 7
Safety Review
Certain precautions should be taken when using electrical products. Please observe the safety hints by
reading the manual and obtaining qualified help if necessary to adhere to the precautions. The power
supply must be switched to the proper mains voltage. Please check the red window on the power
supply to verify the correct setting for your location before connecting the mains plug.
1. Always use a properly grounded power supply cord with this product. Please do
not defeat the ground pin on the mains plug. This connection provides earth to the chassis and
signal grounds inside the device for clean and quiet operation. The “Grounding and interface”
section can help the user/installer clear up a buzz problem if one develops.
2. Avoid high temperature operation in equipment racks by providing air
circulation. The number one killer of electronic gear is HEAT. Vented rack panels may look like
wasted space to an interior decorator, but they look like beauty to a technician or equipment
designer! If the front panel is hot, it is roasting inside the box.
3. Avoid areas of high magnetic fields. The steel chassis of Master is designed to shield
the circuits from EMI and RFI (magnetic and radio interference). When installing equipment in
racks, it is prudent to put power amplifiers and large power supplies at least several rack spaces,
if not in a different rack, away from equipment that deals with low level signals. Separation of
high level and low level equipment can pre-empt trouble caused by heat and EMI.
4. Care should be taken to avoid liquid spills around equipment. If a spill occurs,
please shut off the gear and disconnect the mains. A qualified technician should investigate
accidents to prevent further equipment damage or personnel hazards caused by spills.
5. If one is uncomfortable with opening gear and changing jumpers or making
adjustments, please seek qualified help if necessary.
6. If adjustments or jumper changes are required, please disconnect the mains plug
before opening the top. Dropped screws or tools on a live circuit board can manifest themselves
as burn marks and smoked components. While we feel your pain, (been there) subsequent damage
is not covered by the warranty.
Dangerous Music Incorporated reserves the right to change the specifications or modify the designs
of its equipment. Sending in the registration card is our way of keeping in touch with users of our
equipment should this become necessary. Registration information is always kept confidential and never
disclosed to third parties for any reason. Company contact information is on the last page of this manual.
-2-
The CE sign on this product signifies the fact that the Master has been tested and
verified to conform to the applicable standards of 89/336/EEC. EN55103-1
(emissions) EN61000-2 (immunity) and EN60065:2002 (safety requirements)

Produkt Specifikationer

Mærke: Dangerous Music
Kategori: Processor
Model: Master Cutter

Har du brug for hjælp?

Hvis du har brug for hjælp til Dangerous Music Master Cutter stil et spørgsmål nedenfor, og andre brugere vil svare dig


Processor Dangerous Music Manualer

Dangerous Music

Dangerous Music Master Cutter Manual

3 September 2024
Dangerous Music

Dangerous Music Compressor Manual

30 Juli 2024

Processor Manualer

Nyeste Processor Manualer

Elysia

Elysia mpressor 500 Manual

1 Oktober 2025
Elysia

Elysia karacter Manual

1 Oktober 2025
Elysia

Elysia nvelope 500 Manual

30 September 2025
Elysia

Elysia karacter 500 Manual

30 September 2025
Elysia

Elysia Xpressor 500 Manual

30 September 2025
Elysia

Elysia xpressor Manual

30 September 2025
Elysia

Elysia nvelope Manual

30 September 2025
Datapath

Datapath iolite 600 Manual

29 September 2025
Ground Zero

Ground Zero GZDSP 6-8X PRO Manual

23 September 2025
IMG Stageline

IMG Stageline MFE-212 Manual

21 September 2025