DeWalt DW4055 Manual

DeWalt Ikke kategoriseret DW4055

Læs gratis den danske manual til DeWalt DW4055 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om DeWalt DW4055, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DW4055 Integrated Sanding Frame

and Inversion Stand

WARNING: For your own safety, read the tool instruction manual

before using any accessory. Failure to heed these warnings may result

in personal injury and serious damage to the tool and the accessory.

When servicing this tool, use only identical replacement parts.

FOR USE ONLY WITH THE DW432/433 BELT SANDER

The inversion stand allows the belt sander to be used like a small

stationary sander. It is best when used to sand small pieces of material

that need to maintain a 90-degree edge and cannot easily be sanded

with a hand-held sander.

WARNING: BE SURE THE UNIT IS TURNED OFF AND NOT

ATTACHED TO A POWER SOURCE WHILE INSTALLING THE

SANDING FRAME OR INVERSION STAND. Before reconnecting the

tool, depress and release the trigger switch to ensure that the tool is off.

WARNING: AVOID CONTACTING THE ROTATING BELT ON THE

INVERSION STAND WITH FINGERS OR HANDS. HARSH ABRA-

SIONS COULD RESULT.

TO ATTACH THE SANDING FRAME TO THE BELT SANDER

1. Place the front handle in the top position (A) of the belt sander.

2. Use the hardware provided to attach the sanding frame brace to the

front of the belt sander. Tighten the knob (B) to secure the sander

into the sanding frame (Fig. 1).

3. Seat the tabs (C) on the back end of the sander onto the rod (D)

located on the sanding frame (Fig. 2).

4. Use the angle dial (E) to adjust the belt relative to the work locating

surface as shown in Figure 1.

TO ATTACH SUPPORT BRACE

CAUTION: Support brace must be attached to the inversion stand or

damage may occur.

NOTE: Two support braces are included. Use the appropriate brace

depending on orientation used.

1. Align the holes (L) in the support brace with the inside holes (M) on

the feet.

2. Use the hardware provided to attach the brace to the feet and

secure (Fig. 3).

TO CREATE THE INVERSION STAND

NOTE: The belt sander cannot be properly positioned on the stand with

the dust bag attached. The dust collection system is not operable when

the belt sander is in this mode.

1. Remove dust bag and close the dust collector valve (see tool man-

ual).

2. Use the hardware provided to attach the legs (F) to the sanding

frame to create the working orientation desired, vertical (Fig. 4) or

horizontal (Fig. 5).

3. Use the hardware provided to attach the fence (G) to the sanding

frame.

WARNING: Leave no more than 1/16" (2mm) between the sand-

ing belt and the fence. Pinching and possible injury could result dur-

ing use.

WARNING: Do not allow the fence to touch the sanding belt.

Resulting sparks may ignite dust particles.

4. For Horizontal Sanding Only:

Attach the guard (I) by loosening the wing nut (J) on the left side of

the fence (G). Place the guard between the wing nut and fence.

Rotate the guard into the slot on the frame (K). Tighten wing nut.

5. Clamp or screw the feet to a workbench or flat work surface for sta-

bility using the screw holes (H) in the feet.

6. Adjust the fence to the desired angle and lock in place with the wing

nuts provided.

7. Plug in the sander.

8. Depress the trigger and engage the lock button so the sander is

running.

The following are trademarks for one or more D EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box

configuration; and the array of lozenge-shaped humps on the surface of the tool.

FIG. 4

FIG. 1

FIG. 5

EFIG. 2