Ditek DTK-MB10 Manual

Ditek Ikke kategoriseret DTK-MB10

Læs gratis den danske manual til Ditek DTK-MB10 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Ditek DTK-MB10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Doc # INT-100132-001

Part No. 191556 Rev. 4

DITEK Technical Support Available 24/7

1-888-472-6100 www.ditekcorp.com

DITEK Corporation

ONE DITEK CENTER

1720 Starkey Road

Largo, FL 33771

INSTALLATION

This Surge Protective Device (SPD) is a high performance device, designed to provide protection

for sensitive electronic loads connected to communication loop circuits that have been isolated

from the public switched telephone network or where the SPD is directly connected to the

electronic device. Maximum protection will only be achieved if the SPD is properly installed.

Please read and follow the installation instructions carefully.

NOTICE: This SPD should be installed and grounded, by a licensed contractor, per the applicable

requirements of the NEC and the following instructions. These devices are only to be employed on

communication loop circuits which have been isolated from the Public Switched Telephone Network.

APPLICATION

DTK-MB10 base can be installed inside a 4”x4” electrical boxes and other locations where there is a space

constraint. This base is available as a 1 up array (standard) or 2 through 5 up array for multiple pair

terminations at one point of use. Specify DTK-2MB, 3MB, 4MB or 5MB for 2 through 5 up arrays.

DTK-2MHLPxxFWB surge module is for hardwired series installations for voltages ranging from 5-75 Volts

on circuits that operate at less than 1 Amp.

DTK-2MHLPxxBWB surge module is for hardwired series installations for voltages ranging from 5-75 Volts

on circuits that operate at less than 5 Amps.

DTK-2MHTP surge module is for hardwired series installations for dialer circuits and POTS lines for

communication circuits.

INSTRUCTIONS:

Caution: Measure all voltages to insure applied voltage does not exceed the voltage rating of the unit.

Improper installation voids the warranty.

MB BASE INSTALLATION

1. Turn off the power at the circuit to be protected before beginning installation.

2. Securely mount the snap track between the field wiring and your equipment to be protected. Use the two #8 screws

provided to fasten the snap track.

3. Connect ground to the ground terminal using a minimum of 14 AWG wire, make this conductor as short as possible.

Ground Resistance Rule: Max ground resistance is 25 Ohms, 5 Ohms or less is optimum.

This cannot be an assumed value and must be measured to assure proper grounding.

4. Connect the supply/field wiring to the side of the MB base. Connect the 1st pair to UNPROTECTED

position 1+ and 1- , than the 2nd pair to position 2+ and 2-.

5. Connect the equipment wiring to the side of the MB base. Connect the 1st pair to PROTECTED

position 1+ and 1- , than the 2nd pair to position 2+ and 2-.

6. Make sure the supply/field wiring and equipment wiring conductors do not occupy UNPROTECTED PROTECTED

the same space or conduits.

7. Make sure the wire distance from the base to protected equipment is about 3’ of conductor length. This can be a

coiled service loop if necessary.

MODULE INSTALLATION

Insert the module into the base making sure the polarizing keys in the block are aligned with the notches cut into

the edge card printed circuit board.

8. After all connections have been made and no hazards exist, restore power.

Drawn By: RMitchell 3-3-11

Revised By: RMitchell 6-14-16

SUPPLY WIRING

or FIELD WIRING

GROUNDING

#14AWG MIN.

Pair 1

Pair 2

GND Pair 1

Pair 2

ALLOW FOR 3’ OF CONDUCTOR LENGTH

BETWEEN BASE AND PROTECTED EQUIPMENT

DTK-2MHLP BASE

EQUIPMENT WIRING

3’ SERVICE LOOP

INSTALL INSTRUCTIONS

DTK-2MHLPxxFWB Series, DTK-2MHLPxxBWB Series,

DTK-2MHTPWB, MB10, 2MB-5MB, and DTK-2MHLP Module

Produkt Specifikationer

Mærke:	Ditek
Kategori:	Ikke kategoriseret
Model:	DTK-MB10

Har du brug for hjælp?

Hvis du har brug for hjælp til Ditek DTK-MB10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ditek Manualer

Ditek DTK-DF120S1 Manual

28 September 2025

Ditek D50-CM Manual

30 Januar 2025

Ditek DTK-2MB Manual

30 Januar 2025

Ditek DTK-MB10 Manual

30 Januar 2025

Ditek DTK-GLI Manual

30 August 2024

Ditek DTK-DR120P1 Manual

30 August 2024

Ditek DTK-HVACKIT Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IOptron iEFW-18 Manual

15 December 2025

Magliner CooLift CTA48 Manual

15 December 2025

Epson GP-M831 Manual

15 December 2025

Prince Castle EHB42F1-GMS02 Manual

15 December 2025

SkyRC TX58025 Manual

15 December 2025

La Crosse Technology LTV-THP1-C1 Manual

15 December 2025

Growatt MIN2.5-6KTL-XH2 Manual

15 December 2025

Bosch SBH6YCX02F Manual

15 December 2025

Eurosound HDBT-BYOD-EX1-P Manual

15 December 2025

Milwaukee MX Fuel MXF002 Manual

15 December 2025