Ditek DTK-HVACKIT Manual

Ditek Ikke kategoriseret DTK-HVACKIT

Læs gratis den danske manual til Ditek DTK-HVACKIT (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Ditek DTK-HVACKIT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Doc # INT-100105-001

Part No. 191130 Rev. 7

INSTALL INSTRUCTIONS

DTK-120/240CM+

DITEK Technical Support Available 24/7

1-888-472-6100 www.diteksurgeprotection.com

DITEK Corporation

ONE DITEK CENTER

1720 Starkey Road

Largo, FL 33771

INSTALLATION

This Surge Protective Device (SPD) is a high performance device, designed to provide protection

for sensitive electronic loads connected to service panels, fire panels, or where the SPD is

directly connected to the electronic device. Maximum protection will only be achieved if the SPD

is properly installed. Please read and follow the installation instructions carefully.

NOTICE: This SPD should be installed and grounded, by a licensed contractor, per the applicable

requirements of the NEC and the following instructions.

APPLICATION:

Type 1 SPD - Permanently connected, hard-wired SPDs intended for installation

between the secondary of the service transformer and the line side of the main service equipment

overcurrent protective device.

Type 2 SPD - Permanently connected, hard wired SPDs intended for installation on the load side of the

main serivice equipment’s overcurrent protective device.

For 120/240VAC split circuits with L1-G = 120VAC, L2-G = 120VAC, L1-L2 = 240VAC

INSTRUCTIONS:

Caution: Measure all voltages to insure applied voltage does not exceed the voltage rating of the

unit. Improper installation voids the warranty. This unit must be connected in parallel with the

equipment to be protected.

Warning: No Serviceable Parts-Attention:Aucune pièce remplaçable ou réparable

For Use Only With A Flexible Conduit System Or Direct Connection To Panel

NOTE: When used as a Type 2 SPD, it is suitable for use on a circuit capable of delivering not more

than 10,000 rms symmetrical Amperes, when protected by a minimum 20 Ampere circuit breaker rated

120 Volts minimum.

HVAC Disconnect/Breaker Panel Installation:

1. Turn off main power before beginning the installation.

2. Remove the front cover from panel.

3. Remove a 3/4" knockout on the side of the panel box.

4. Unscrew nut from unit.

5. Feed all wires through the knockout hole then through nut. Tighten the nut to secure the unit.

6. Connect the green (Ground) wire to the ground bus.

7. Always have one common ground per system to eliminate a differential in ground potentials.

Ground Resistance Rule: Max ground resistance is 25 ohms, 5 ohms or less is optimum.

This cannot be an assumed value and must be measured to assure proper grounding.

8. Connect the phase (Black) wires to the load side of a 2 pole breaker, making sure the leads are as

short as possible (Ground being the shortest).

9. After all connections have been made and no hazards exist, restore power.

120VAC Single Phase Installation:

1. Mount this device using the mounting feet or to disconnect or breaker panel using the installation

instructions for Disconnect/Breaker Panel Installation instructions above.

2. Connect the green (Ground) wire to the ground circuit.

3. Always have one common ground per system to eliminate the possibility of a differential in

ground potentials.

Ground Resistance Rule: Max ground resistance is 25 ohms, 5 ohms or less is optimum.

This cannot be an assumed value and must be measured to assure proper grounding.

4. Connect both phase (Black) wires to the load side of the 120VAC single phase circuit, making sure

the leads are as short as possible (Ground being the shortest).

5. After all connections have been made and no hazards exist, restore power.

NOTE: The LED on the unit must be on, if the LED is off than surge protection is compromised and

the unit must be replaced.

This device features an internal protection feature that will disconnect the surge protective components but

will maintain power to the load - now unprotected. If this situation is undesirable for the application, follow

the manufacturer’s instructions for replacing the device.

Drawn By: R.Mitchell 5-2-13

Revision By: R. Mitchell 10/7/19

Produkt Specifikationer

Mærke:	Ditek
Kategori:	Ikke kategoriseret
Model:	DTK-HVACKIT

Har du brug for hjælp?

Hvis du har brug for hjælp til Ditek DTK-HVACKIT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ditek Manualer

Ditek DTK-DF120S1 Manual

28 September 2025

Ditek D50-CM Manual

30 Januar 2025

Ditek DTK-2MB Manual

30 Januar 2025

Ditek DTK-MB10 Manual

30 Januar 2025

Ditek DTK-GLI Manual

30 August 2024

Ditek DTK-DR120P1 Manual

30 August 2024

Ditek DTK-HVACKIT Manual

30 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Iogear GCS1908W Manual

30 Oktober 2025

Reflecta 23295 Manual

30 Oktober 2025

Calorex Delta DT 4 Manual

30 Oktober 2025

Abus HUD-Y ACE PURE Manual

30 Oktober 2025

Krups FDK442 Manual

30 Oktober 2025

Iogear GCS62HDPKIT Manual

30 Oktober 2025

Eliminator Lighting E 107 Manual

30 Oktober 2025

Segway eScooter E150S Manual

30 Oktober 2025

Phoenix Gold ZD-VOL4 Manual

30 Oktober 2025

Olimpia Splendid Bi2 SLIR NAKED Manual

30 Oktober 2025