Dito Sama 600433 Manual

Dito Sama Skæremaskine 600433

Læs gratis den danske manual til Dito Sama 600433 (10 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Dito Sama 600433, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/10
1
A Pusher
B Ram press
C Hopper
D Ejector
E Cutting chamber
F Drive shaft
G Body
H Casing
I Inclinable base
J Strut
K Control panel
L Locking pin
M Bowl
N Bowl handle
O Lid locking handle
P Rotor
Q Lid
R Scraper handle
1.1 DESCRIPTION
The combined vegetable slicer/cutter is a preparation machine
that provides two functions:
1) Cutting vegetables (cut - slice - shred - grate - ) Cutting chips
and dices.
2) Cutter-mixer for reducing condiments, emulsions, and sauces,
various liquidising operations, and cuttering meat. The vegeta-
ble cutting function is designed to allow cutting of all types of
products, by means of a lever-operated hopper. This combined
appliance equipped with the lever-operated hopper and cutter is
very appropriate for restaurant and small community kitchens.
• Control panel
A ON switch, to operate at the selected speed.
B STOP switch.
C ON switch, to operate at the selected speed,
while held pressed in.
E Display of selected speed
F Increase speed
G Decrease speed
GB
TRK2 GB 02 2018
1.1
1.2
Refer to the numbered drawings that go with the numbered
paragraphs in the instructions.
Contents
Introduction 1
Introduction 1
Installation. 1
Use, Safety 3
Cleaning, Hygiene, Storage 7
Fault finding 8
Maintenance 9
Compliance with regulations 10
Introduction
The User Manual contains useful information for
the user on how to work correctly and in complete
safety, and is designed to make it easier to use the
machine (called “machine” or “appliance” below).
What follows is in no case intended to be a long list of warnings
and constraints, but rather as a series of instructions meant
to improve the service provided by the machine in every res-
pect, and particularly to avoid a series of injuries or damage to
equipment that might result from inappropriate procedures for
use and management.
It is essential that all the people responsible for transporting,
installing, commissioning, using, maintaining, repairing or
dismantling the machine should consult this manual and read
it carefully before proceeding with the various operations, in
order to avoid any incorrect or inappropriate handling that
might be result in damage to the machine or put people’s
safety at risk.
It is just as important that the Manual should always be avai-
lable to the operator and it should be kept carefully where the
machine is used ready for easy and immediate consultation in
case of any doubt, or in any case, whenever the need arises.
If after reading the Manual, there are still any doubts concerning
how to use the machine, please do not hesitate to contact the
Manufacturer or approved After Sales Service provider, who
is constantly available to ensure quick and careful service for
improved machine operation and optimum efficiency.
Note that the safety, hygiene and environmental protection stan-
dards currently applicable in the country where the machine is
installed must always be applied during all phases of machine
operation. Consequently it is the user’s responsibility to ensure
that the machine is operated and used solely under the optimum
safety conditions laid down for people, animals and property.
Introduction
Installation
04/2022
ATTENTION!!
Machine storage: -25°C to +50°C
Ambient temperature during operation: +4°C to +40°C
This machine is for professional use and must be used by staff trained to use, clean and maintain it, in terms or reliability
and safety.
Use the machine in adequately lit premises (See applicable technical standard for the country of use. In Europe, refer to standard
EN 12464-1)
When handling the machine, always check that the parts taken hold of are not mobile elements: risk of dropping and injury
to the lower limbs.
The machine is not designed for use in explosive atmospheres.
The reference language for these instructions is French.

Produkt Specifikationer

Mærke: Dito Sama
Kategori: Skæremaskine
Model: 600433

Har du brug for hjælp?

Hvis du har brug for hjælp til Dito Sama 600433 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skæremaskine Dito Sama Manualer

Dito Sama

Dito Sama 600438 Manual

13 August 2025
Dito Sama

Dito Sama 600980 Manual

13 August 2025
Dito Sama

Dito Sama 600979 Manual

13 August 2025
Dito Sama

Dito Sama 600435 Manual

13 August 2025
Dito Sama

Dito Sama 600433 Manual

13 August 2025
Dito Sama

Dito Sama 602206 Manual

13 August 2025
Dito Sama

Dito Sama 603432 Manual

13 August 2025
Dito Sama

Dito Sama 600982 Manual

13 August 2025
Dito Sama

Dito Sama 600970 Manual

12 August 2025
Dito Sama

Dito Sama 600428 Manual

12 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Vollrath

Vollrath Redco Instacut Manual

15 December 2025
Maestro

Maestro MR-590 Manual

8 December 2025
Maestro

Maestro MR-591 Manual

8 December 2025
Omcan

Omcan 11399 Manual

5 December 2025
Vevor

Vevor SK-720L Manual

2 December 2025
Vevor

Vevor PGYHJ3626 Manual

2 December 2025
Lakeland

Lakeland 62167 Manual

2 December 2025
Vevor

Vevor PGYHJ2814 Manual

1 December 2025
Vevor

Vevor PGYHJ2615 Manual

30 November 2025
Sommertal

Sommertal AS170 Manual

30 November 2025