Doepfer A-135-2v Manual

Doepfer Ikke kategoriseret A-135-2v

Læs gratis den danske manual til Doepfer A-135-2v (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Doepfer A-135-2v, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

DOEPFER MUSIKELEKTRONIK GMBH

DOEPFER MUSIKELEKTRONIK GMBH DOEPFER MUSIKELEKTRONIK GMBH

A-135-2 Quad VCA / Voltage Controlled Mixer

Position and function of the jumpers and connectors Board A

The pin headers JP4, JP5, JP6 and JP7 are used to determine the control voltages for the VCAs 2-4:

JP4: VCA2 control

jumper in upper position Æ VCA2 is controlled by CV2 (factory setting)

jumper in lower position Æ VCA2 is controlled by CV1 (in this case CV2 does not affect VCA2)

JP5: VCA3 control

jumper in upper position Æ VCA3 is controlled by CV3 (factory setting)

jumper in lower position Æ VCA3 is controlled by CV1 (in this case CV3 does not affect VCA3)

JP6: VCA4 control

jumper in upper position Æ VCA4 is controlled by CV4 (factory setting)

jumper in lower position Æ VCA4 is controlled by CV1 (in this case CV4 does not affect VCA3)

JP7: alternative VCA4 control

jumper installed Æ VCA4 is controlled by CV2 (used for "Stereo" mode)

In this case the jumper on JP6 has to be removed !

JP4: VCA2 control

Bus connector

(colored stripe left)

JP5: VCA3 control

JP6: VCA4 control

JP7: alternative

VCA4 control

Applications of the different jumper settings

Remark: under all conditions VCA1 is controlled by control unit 1.

This is the standard configuration:

• JP4, JP5 and JP6 are installed in the upper position

• no jumper is installed on JP7

In this case each VCA has it's own control unit.

"Stereo" configuration:

• JP4 is installed in the upper position (VCA2 is controlled by CV2)

• JP5 is installed in the lower position (VCA3 is controlled by CV1)

• JP6 is removed

• JP7 is installed (VCA4 is controlled by CV2)

In this configuration VCA1 and VCA3 are controlled by CV1, VCA2 and VCA4 are controlled by CV2.

The control units 3 and 4 have no meaning in this confuguration.

Special configuration (all four VCAs are controlled by CV1):

• JP4, JP5 and JP6 are installed in the lower position

• no jumper is installed on JP7

In this configuration all four VCAs are controlled by CV1. The control units 2, 3 and 4 have no meaning in this

application. This configuration is used when four different audio or control signals have to be controlled

simultaneously (e.g the level of four VCOs, four LFOs, four envelope generators and so on). It's the same

function as the obsolete quad VCA module A-132-2.

Produkt Specifikationer

Mærke:	Doepfer
Kategori:	Ikke kategoriseret
Model:	A-135-2v

Har du brug for hjælp?

Hvis du har brug for hjælp til Doepfer A-135-2v stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Doepfer Manualer

Doepfer A-100 Manual

1 September 2024

Doepfer Dark Link Manual

21 August 2024

Doepfer A-196 Manual

20 August 2024

Doepfer A-134 Manual

20 August 2024

Doepfer A-135-2v Manual

19 August 2024

Doepfer A-145 Manual

19 August 2024

Doepfer A-101-2 Manual

19 August 2024

Doepfer A-99 Manual

19 August 2024

Doepfer A-103 Manual

19 August 2024

Doepfer A-165 Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

QSC RMXa Manual

13 September 2025

Tineco Floor One S2 Series Manual

13 September 2025

Tineco Floor One S3 Breeze Manual

13 September 2025

Tineco Floor One S5 Steam Manual

13 September 2025

Osram VX500-CB Manual

13 September 2025

Zelmer ZTS7990 Manual

13 September 2025

Osram VX250-SP Manual

13 September 2025

Vello CB-800 Manual

13 September 2025

Ibm System Storage ProtecTIER TS7620 Manual

13 September 2025

Ibm System Storage N6250 Manual

13 September 2025