Draper 03187 Manual

Draper Lys 03187

Læs gratis den danske manual til Draper 03187 (14 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Draper 03187, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/14

Original Instructions

Version 1 – March 2022

LED SMD

TRIPOD

SITE LIGHT

These are the original product instructions. This document is part of the product; retain it for the life of the product, passing it on to subsequent holders. Read

this manual in full before attempting to assemble, operate, or maintain this product. Always use the latest version of the product manual. The latest version can

be downloaded from drapertools.com/manuals

1. Specication

Stock No. Part No. Supply voltage Bulb wattage (W) Lumens (lm) Beam angle (°) Colour temperature (K)

03187 110V/TSL/10W 110V at 50Hz

1,100

100 6,000~6,500

03188 110V/TSL/20W 110V at 50Hz

2,200

100 6,000~6,500

03192 110V/TSL/30W 110V at 50Hz

3,300

100 6,000~6,500

03193 110V/TSL/50W 110V at 50Hz

5,500

100 6,000~6,500

03206 230V/TSL/10W

230V at 50Hz

1,100

100 6,000~6,500

03207 230V/TSL/10W

230V at 50Hz

2,200

100 6,000~6,500

03208 230V/TSL/10W

230V at 50Hz

3,300

100 6,000~6,500

03210 230V/TSL/10W

230V at 50Hz

5,500

100 6,000~6,500

EU 04351 230V/TSL/20WFOB

230V at 50Hz

2,200

100 6,000~6,500

EU 04354 230V/TSL/50WFOB

230V at 50Hz

5,500

100 6,000~6,500

This light is rated IP65. It is fully protected against dust and is protected

against low pressure jets of water from all directions (limited ingress

permitted). This does not include the attached plug.

2. Health and Safety Information

Important: Read all Health and Safety instructions before attempting to

operate, maintain or repair this product. Non-compliance with these

instructions may result in injury or damage to the user or the product.

Draper Tools accepts no responsibility for improper use of this device.

• Inspect the product and electrical connections for signs of damage

before every use.

WARNING! Do not use the product if defects are present and

withdraw it from service until it has been repaired. If the external

power cable is damaged, it must be replaced by suitably qualied

personnel or returned to Draper Tools for repair.

• If required, use an extension lead appropriate for both the product and

the environment in which it is used.

− Ensure the extension lead is fully unwound regardless of the

distance from the power supply to the light.

− Use a Residual Current Device (RCD) in damp environments.

• Always ensure that the voltage rating on the product is appropriate for

the power supply to be used and that the plug is tted with the correct

fuse.

• Remove all packaging and wrapping before use.

• Position the product appropriately.

− Use only on level surfaces.

− Ensure that the product is stable and unlikely to tip over.

− Apply weights to the tripod legs where necessary.

− To prevent tripping, clearly mark or place barriers around the base

of the product where possible.

− This is a Class I appliance and requires an earth connection to

protect against electric shock from accessible conductive parts in

the event of failure of the basic insulation.

• Ensure that all joints and attachments are securely fastened when the

product is in use or stored.

• Keep trailing cables and extension leads tidy and secured to avoid trip

hazards.

• DO NOT carry the light by the cable or plug.

• WARNING! This product gets hot when in use.

− NEVER place objects on the lamp area or hang objects on any part

of this product.

− NEVER use the light near ammable or combustible substances or

equipment.

− ALWAYS disconnect the power supply and allow at least ten minutes

for the product to cool before attempting any maintenance or

adjustment.

• ALWAYS switch o the light before disconnecting the mains power.

WARNING! Do not stare at the operating light source.

• DO NOT pull on the cable to disconnect the light from mains power.

• This product is certied for use in ambient temperatures of -20 to +45°C.

• Replace any cracked protective shield.

− This product includes a 4mm glass shield rated IK08.

3. Maintenance and Troubleshooting

Important: Maintenance and repair, including replacement of the light

source, must only be performed by qualied personnel with sucient

knowledge of the electrical circuits used in this device.

• Always disconnect the power supply and allow the lamp to cool before

cleaning.

• Clean the lamp using a dry cloth ONLY.

CAUTION! Do not immerse this product in water.

• Store the product in a clean and dry environment, out of reach of

children, with all joints rmly secured.

− Use a Residual Current Device (RCD) in damp environments.

If the light does not illuminate when switched on, check that all power

connections are secured and active.

Risk of electric shock

Class I product, must be earthed

Replace any cracked

protective shield

5. Operation Instructions

Before use, check that all parts are present and not damaged.

Depending on the Stock Number, the product shipped may dier slightly

from the product illustrated in this document.

11. Disposal

Do not dispose of electrical products with household waste. At the end of

its working life, or when it can no longer be repaired, dispose of the site

light according to local regulations.

Helpline: +44 (0) 23 8049 4344 Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 Website: drapertools.com Email: sales@drapertools.com

Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF, UK

Delta International, Delta International BV, Oude Graaf 8, 6002 NL, Weert, Netherlands

2 Fig.

4. What’s in The Box?

Carefully remove the product from the packaging and examine it for any

signs of damage that may have occurred during shipment.

(A) Telescopic tripod (B) LED SMD site light

(A)

(B)

1 Fig.

1. Mains power cable 2. On/o button

(2)(1)