Draper 03711 Manual

Draper Ikke kategoriseret 03711

Læs gratis den danske manual til Draper 03711 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Draper 03711, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Original Instructions

Version 1 – February 2022

21714, 21715, 21721, 82631, 21723, 21744, 03711

METRIC THREAD

REPAIR KIT

Stock No. Part No. Tap size

Drill bit size

(mm)

Hex key size

(mm)

Thread inserts

included

21714 DHCK-A M5 x 0.8mm 5.2 2 20

21715 DHCK-A M6 x 1.0mm 6.2 2 20

21721 DHCK-A M8 x 1.25mm 8.3 2 20

82631 DHCK-A M9 x 1.25mm 9.3 2 20

21723 DHCK-A M10 x 1.5mm 10.3 2 10

21744 DHCK-A M12 x 1.75mm 12.4 2 10

03711 DHCK-A M14 x 1.25mm 14.3 2 10

(E)

(A)

(B)

(F)

(D)

(C)

A. 1 x HSS drill bit

B. 1 x HSS

tapping tool

C. 1 x Hex key

D. 1 x Insert tool

E. 1 x Lug

breaking tool

F. Thread inserts

G. 1 x Case

1. Health and Safety

Information

• Inspect the product thoroughly for

damage before every use; use it if DO NOT

it is damaged.

• ALWAYS wear eye protection.

• This manual is supplied as a guide only.

− Assess any other precautions that

must be taken before use with each

specic workpiece.

− Where the workpiece is part of a larger

tool or machine, refer to the

manufacturer’s manual for the correct

procedure for use.

• Keep the work area clean and well lit,

with bystanders at a safe distance.

• Secure the workpiece during operation.

WARNING! This product requires the use of

additional tools (not supplied). Read and

adhere to all Health and Safety information

and operating instructions associated with

the chosen tools before use.

Read this manual in full before attempting to use this product and retain it for later use.

Always use the latest version of the manual.

(G)

Fig. 1

Fig. 4

Fig. 3

Fig. 6

Fig. 2

Fig. 5

Helpline: +44 (0) 23 8049 4344 Sales Desk: +44 (0) 23 8049 4333

General Enquiries: +44 (0) 23 8026 6355 Website: drapertools.com

Email: sales@drapertools.com

Draper Tools Limited, Hursley Road, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF, UK

6. With the insert tool at the correct angle,

wind the thread insert into the hole using

light downward pressure until the set

depth is reached and then remove the

insert tool – Fig. 5.

CAUTION! DO NOT work against the

direction of the thread as this may

damage the insert tang.

7. Position the lug breaking tool (E) above

the insert thread tang and strike it to

break the tang – Fig. 6.

3. Care and Disposal

• Clean all parts of the product before and

after each use, and before storing.

• Do not use damaged or defective tools

with this product.

• Store the product in a clean and dry

location, out of reach of children.

At the end of its working life, or when it can

no longer be repaired, dispose of this product

according to local regulations.

Wear eye and face protection

2. Operating Instructions

1. Drill out the damaged thread using the

appropriate drill bit (A) (supplied) – Fig. 1.

Important: Some xings may need to be

removed by a specialist engineer. Draper

Tools accepts no responsibility for the

incorrect removal of broken xings and

fasteners.

2. Use a thread gauge (not supplied) to

ensure that the thread and pitch of the

new fastener are compatible with the

thread insert (F) – Fig. 2.

3. Fix the tapping tool (B) into a tap wrench

(not supplied) and cut a new thread into

the cleared hole – Fig. 3.

Important: Use of an appropriate cutting

oil is recommended. Clear the tapping

tool of chips after use.

4. Use the adjustable ring of the insert tool

(D) to set the depth at which the thread

insert will be positioned and use the hex

key (C) to lock it in place – Fig. 4.

Important: When inserted, the thread

insert should be positioned roughly a

half-turn below the surface.

5. With the thread insert tang positioned at

the bottom, push the insert tool through

the top of the thread insert and locate the

tang in the tang slot.

Produkt Specifikationer

Mærke:	Draper
Kategori:	Ikke kategoriseret
Model:	03711

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper 03711 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Draper Manualer

5 August 2025

15 Juni 2025

9 Juni 2025

8 Juni 2025

8 Juni 2025

Draper Expert 17195 Manual

8 Juni 2025

Draper 09536 Manual

8 Juni 2025

Draper Expert 30969 Manual

8 Juni 2025

Draper 90126 Manual

8 Juni 2025

Draper 93510 Manual

7 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rowenta Adagio BV3101 Manual

12 August 2025

Klein Tools VDV826-705 Manual

12 August 2025

Walrus Audio Canvas Clock Manual

12 August 2025

Rowenta Artik Ionic VU9020 Manual

12 August 2025

Slingshot S (2024) Manual

12 August 2025

Discover D713U Manual

12 August 2025

Tefal Virtuo FV1712 Manual

12 August 2025

Mars Gaming MF-LINKFINITYKIT2R Manual

12 August 2025

Rowenta City Space Cyclonic RO2544 Manual

12 August 2025

Beverage-Air PRT2XTHC-1AS Manual

12 August 2025