Draytek Vigor AP 810 Manual

Draytek Wifi Vigor AP 810

Læs nedenfor 📖 manual på dansk for Draytek Vigor AP 810 (177 sider) i kategorien Wifi. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/177

VigorAP 810 User’s Guide

VigorAP 810 User’s Guide ii

r’

’s

Version: 2.2

Firmware Version: V1.2.5

(For future update, please visit DrayTek web site)

Date: September 13, 2018

VigorAP 810 User’s Guide

iii

Declarations

system, or translated into any language without written permission from the copyright

holders.

Trademarks

The following trademarks are used in this document:

 Microsoft is a registered trademark of Microsoft Corp.

 Windows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are

trademarks of Microsoft Corp.

 Apple and Mac OS are registered trademarks of Apple Inc.

 Other products may be trademarks or registered trademarks of their respective

manufacturers.

Safety Instructions and Approval

Safety

Instructions

 Read the installation guide thoroughly before you set up the modem.

 The modem is a complicated electronic unit that may be repaired only be

authorized and qualified personnel. Do not try to open or repair the modem

yourself.

 Do not place the modem in a damp or humid place, e.g. a bathroom.

 The modem should be used in a sheltered area, within a temperature range of +5

to +40 Celsius.

 Do not expose the modem to direct sunlight or other heat sources. The housing

and electronic components may be damaged by direct sunlight or heat sources.

 Do not deploy the cable for LAN connection outdoor to prevent electronic shock

hazards.

 Keep the package out of reach of children.

 When you want to dispose of the modem, please follow local regulations on

conservation of the environment.

Warranty

We warrant to the original end user (purchaser) that the modem will be free from any

defects in workmanship or materials for a period of two (2) years from the date of

purchase from the dealer. Please keep your purchase receipt in a safe place as it serves

as proof of date of purchase. During the warranty period, and upon proof of purchase,

should the product have indications of failure due to faulty workmanship and/or

materials, we will, at our discretion, repair or replace the defective products or

components, without charge for either parts or labor, to whatever extent we deem

necessary tore-store the product to proper operating condition. Any replacement will

consist of a new or re-manufactured functionally equivalent product of equal value, and

will be offered solely at our discretion. This warranty will not apply if the product is

modified, misused, tampered with, damaged by an act of God, or subjected to abnormal

working conditions. The warranty does not cover the bundled or licensed software of

other vendors. Defects which do not significantly affect the usability of the product will

not be covered by the warranty. We reserve the right to revise the manual and online

documentation and to make changes from time to time in the contents hereof without

obligation to notify any person of such revision or changes.

Be a Registered

Owner Web registration is preferred. You can register your Vigor modem via

http://www.draytek.com.

Firmware & Tools

Updates Due to the continuous evolution of DrayTek technology, all modems will be regularly

upgraded. Please consult the DrayTek web site for more information on newest

firmware, tools and documents.

http://www.draytek.com

VigorAP 810 User’s Guide iv

VigorAP 810 User’s Guide

Introduction .................................................................................................1

1.1 Introduction ............................................................................................................................. 1

1.2 LED Indicators and Connectors.............................................................................................. 2

1.3 Hardware Installation .............................................................................................................. 4

1.3.1 Wired Connection for PC in LAN...................................................................................... 4

1.3.2 Wired Connection for Notebook in WLAN........................................................................ 5

1.3.3 Wireless Connection......................................................................................................... 6

1.3.4 POE Connection............................................................................................................... 7

Network Configuration................................................................................9

2.1 Windows 7 IP Address Setup..................................................................................................9

2.2 Windows 2000 IP Address Setup...........................................................................................11

2.3 Windows XP IP Address Setup............................................................................................. 12

2.4 Windows Vista IP Address Setup.......................................................................................... 13

2.5 Accessing to Web User Interface.......................................................................................... 14

2.6 Changing Password.............................................................................................................. 15

2.7 Quick Start Wizard ................................................................................................................ 16

2.7.1 Configuring Wireless Settings – General........................................................................ 16

2.7.2 Configuring 2.4GHz Wireless Settings Based on the Operation Mode.......................... 17

2.7.3 Finishing the Wireless Settings Wizard.......................................................................... 24

2.8 Online Status......................................................................................................................... 25

Advanced Configuration.................................................................................27

3.1 Operation Mode .................................................................................................................... 28

3.2 LAN ....................................................................................................................................... 29

3.2.1 General Setup................................................................................................................. 29

3.2.2 Web Portal...................................................................................................................... 32

3.3 Central AP Management.......................................................................................................35

3.3.1 General Setup................................................................................................................. 35

3.3.2 APM Log......................................................................................................................... 36

3.3.3 Function Support List...................................................................................................... 36

3.3.4 Overload Management................................................................................................... 37

3.3.5 Status of Settings............................................................................................................ 38

3.4 General Concepts for Wireless LAN..................................................................................... 39

3.5 Wireless LAN Settings for AP Mode ..................................................................................... 41

VigorAP 810 User’s Guide vi

3.5.1 General Setup................................................................................................................. 42

3.5.2 Security........................................................................................................................... 44

3.5.3 Access Control................................................................................................................ 47

3.5.4 WPS................................................................................................................................ 48

3.5.5 Advanced Setting............................................................................................................ 49

3.5.6 AP Discovery.................................................................................................................. 51

3.5.7 WMM Configuration........................................................................................................ 52

3.5.8 Bandwidth Management................................................................................................. 54

3.5.9 Airtime Fairness.............................................................................................................. 55

3.5.10 Station Control.............................................................................................................. 57

3.5.11 Roaming ....................................................................................................................... 58

3.5.12 Station List.................................................................................................................... 60

3.6 Wireless LAN Settings for Station-Infrastructure Mode.......................................................... 62

3.6.1 General Setup................................................................................................................. 62

3.6.2 Site Survey ..................................................................................................................... 67

3.6.3 Statistics.......................................................................................................................... 68

3.6.4 WPS (Wi-Fi Protected Setup)......................................................................................... 68

3.7 Wireless LAN Settings for AP Bridge-Point to Point/AP Bridge-Point to Multi-Point Mode .. 70

3.7.1 General Setup................................................................................................................. 70

3.7.2 Advanced Setting............................................................................................................ 72

3.7.3 AP Discovery.................................................................................................................. 74

3.7.4 WDS AP Status .............................................................................................................. 76

3.8 Wireless LAN Settings for AP Bridge-WDS Mode ................................................................ 77

3.8.1 General Setup................................................................................................................. 78

3.8.2 Security........................................................................................................................... 81

3.8.3 Access Control................................................................................................................ 84

3.8.4 WPS................................................................................................................................ 85

3.8.5 Advanced Setting............................................................................................................ 86

3.8.6 AP Discovery.................................................................................................................. 88

3.8.7 WDS AP Status .............................................................................................................. 89

3.8.8 WMM Configuration........................................................................................................ 90

3.8.9 Bandwidth Management................................................................................................. 92

3.8.10 Airtime Fairness............................................................................................................ 93

3.8.11 Station Control.............................................................................................................. 95

3.8.12 Roaming ....................................................................................................................... 96

3.8.13 Station List.................................................................................................................... 98

3.9 Wireless LAN Settings for Universal Repeater Mode........................................................... 99

3.9.1 General Setup............................................................................................................... 100

3.9.2 Security......................................................................................................................... 102

3.9.3 Access Control.............................................................................................................. 105

3.9.4 WPS.............................................................................................................................. 106

3.9.5 Advanced Setting.......................................................................................................... 107

3.9.6 AP Discovery................................................................................................................ 110

3.9.7 Universal Repeater....................................................................................................... 111

3.9.8 WMM Configuration...................................................................................................... 114

3.9.9 Bandwidth Management............................................................................................... 116

3.9.10 Airtime Fairness.......................................................................................................... 117

3.9.11 Station Control............................................................................................................ 119

3.9.12 Roaming ..................................................................................................................... 120

3.9.13 Station List.................................................................................................................. 122

3.10 RADIUS Setting ................................................................................................................ 124

3.10.1 RADIUS Server........................................................................................................... 124

3.10.2 Certificate Management ............................................................................................. 125

3.11 Applications ....................................................................................................................... 126

VigorAP 810 User’s Guide 2

Before you use the Vigor modem, please get acquainted with the LED indicators and

connectors first.

Status Explanation

Off The system is not ready or is failed. ACT

Blinking The system is ready and can work normally.

On A USB device is connected and active. USB

Blinking The data is transmitting.

On A normal connection is through its corresponding

port.

Off LAN is disconnected.

LAN B

Blinking Data is transmitting (sending/receiving).

On A normal connection is through its corresponding

port. LAN A1 - A4

Off LAN is disconnected.

On Press the button and release it within 2 seconds. When the

wireless function is ready, the green LED will be on.

Off Press the button and release it within 2 seconds to turn off

the WLAN function. When the wireless function is not

ready, the LED will be off.

WLAN

(Green LED) on

WLAN button

Blinking

(Green) Data is transmitting (sending/receiving).

WPS

(Orange LED) on

WLAN button

Blinking

(

Orange

)

When WPS function is enabled by web user interface,

press this button for more than 2 seconds to wait for

client’s device making

network connection through WPS.

When the orange LED blinks with 1 second cycle for 2

minutes, it means that the AP is waiting for wireless client

to connect

with it.

USB Connector for a printer.

VigorAP 810 User’s Guide

Interface Description

LAN B Connecter for xDSL / Cable modem (Giga level)

or router.

LAN A1 (PoE) -

A4 Connecter for xDSL / Cable modem (Giga level) /

computer or router.

Restore the default settings. Usage: Turn on the

AP. Press the button and keep for more than 6

seconds. Then the AP will restart with the factory

default configuration.

ON/OFF: Power switch.

PWR: Connecter for a power adapter.

VigorAP 810 User’s Guide 6

VigorAP 810 can access Internet via an ADSL modem, router, or switch/hub in your

network through wireless connection.

1. Connect VigorAP 810 to ADSL modem or router via wireless network.

2. Connect the A/C power adapter to the wall socket, and then connect it to the PWR

connector of the access point.

3. Power on VigorAP 810.

4. Check all LEDs on the front panel. ACT LED should be steadily on, LAN LEDs

should be on if VigorAP 810 is correctly connected to the ADSL modem, router or

switch/hub.

(For the detailed information of LED status, please refer to section 1.2.)

VigorAP 810 User’s Guide

VigorAP 810 can gain the power from the connected switch, e.g., VigorSwitch P2260. PoE

(Power over Ethernet) can break the install limitation caused by the fixed power supply.

1. Connect VigorAP 810 to a switch in your network through the LAN A1 (PoE) port of

the access point by Ethernet cable.

2. Connect a computer to VigorSwitch P2260. Make sure the subnet IP address of the PC

is the same as VigorAP 810 management IP, e.g., 192.168.1.X.

3. Power on VigorAP 810.

4. Check all LEDs on the front panel. ACT LED should be steadily on, LAN LEDs

should be on if the access point is correctly connected to the ADSL modem, router or

switch/hub.

VigorAP 810 User’s Guide 8

This page is left blank.

VigorAP 810 User’s Guide 10

Then, select Internet Protocol Version 4 (TCP/IPv4) and click Properties.

Under the General tab, click Use the following IP address. Then input the following

settings in respective field and click OK when finish.

IP address: 192.168.1.9

Subnet Mask: 255.255.255.0

VigorAP 810 User’s Guide

Click Start button (it should be located at lower-left corner of your computer), then click

control panel. Double-click Network and Dial-up Connections icon, double click Local

Area Connection, and Local Area Connection Properties window will appear. Select

Internet Protocol (TCP/IP), then click Properties.

Select Use the following IP address, then input the following settings in respective field and

click OK when finish.

IP address: 192.168.1.9

Subnet Mask: 255.255.255.0

VigorAP 810 User’s Guide

Click Start button (it should be located at lower-left corner of your computer), then click

control panel. Click View Network Status and Tasks, then click Manage Network

Connections. Right-click Local Area Netwrok, then select ‘Properties’. Local Area

Connection Properties window will appear, select Internet Protocol Version 4 (TCP /

IPv4), and then click Properties.

Select Use the following IP address, then input the following settings in respective field and

click OK when finish:

IP address: 192.168.1.9

Subnet Mask: 255.255.255.0.

VigorAP 810 User’s Guide 14

All functions and settings of this access point must be configured via web user interface.

Please start your web browser (e.g., IE).

1. Make sure your PC connects to the VigorAP 810 correctly.

2. Open a web browser on your PC and type http://192.168.1.2. A pop-up window will

open to ask for username and password. Pease type “admin/admin” on

Username/Password and click OK.

Note 1: You may either simply set up your computer to get IP dynamically from the

router or set up the IP address of the computer to be in the same subnet as the IP

address of VigorAP 810.

 If there is no DHCP server on the network, then VigorAP 810 will have an IP

address of 192.168.1.2.

 If there is DHCP available on the network, then VigorAP 810 will receive it’s

IP address via the DHCP server.

3. The Main Screen will pop up.

VigorAP 810 User’s Guide

Note: If you fail to access to the web configuration, please go to “Trouble

Shooting” for detecting and solving your problem. For using the device properly, it

is necessary for you to change the password of web configuration for security and

adjust primary basic settings.

1. Please change the password for the original security of the modem.

2. Go to System Maintenance page and choose Administration Password.

3. Enter the new login password on the field of Password. Then click OK to continue.

4. Now, the password has been changed. Next time, use the new password to access the

Web User Interface for this modem.

VigorAP 810 User’s Guide 16

Quick Start Wizard will guide you to configure 2.4G wireless setting, 5G wireless setting

and other corresponding settings for Vigor Access Point step by step.

–

This page displays general settings for the operation mode selected.

Available settings are explained as follows:

Item Description

Operation Mode There are six operation modes for wireless connection. Settings

for each mode are different.

After finishing this web page configuration, please click Next to continue.

VigorAP 810 User’s Guide

In this page, the advanced settings will vary according to the operation mode chosen on

2.7.1.

When you choose AP as the operation mode for wireless LAN (2.4GHz), you will need to

configure the following page.

Available settings are explained as follows:

Item Description

Channel Means the channel frequency of the wireless LAN. The default

channel is 6. You may switch channel if the selected channel is

under serious interference. If you have no idea of choosing the

frequency, please select AutoSelect to let system determine for

you.

Main SSID Set a name for VigorAP to be identified.

Security Key Type 8~63 ASCII characters, such as 012345678..(or 64

Hexadecimal digits leading by 0x, such as "0x321253abcde...").

Enable Guest

Wireless Check the box to enable the guest wireless setting.

Such feature is especially useful for free Wi-Fi service. For

example, a coffee shop offers free Wi-Fi service for its guests

for one hour every day.

SSID – Set a name for VigorAP which can be identified and

connected by wireless guest.

VigorAP 810 User’s Guide 18

Security Key – Set 8~63 ASCII characters or 8~63 ASCII

characters which can be used for logging into VigorAP by

wireless guest.

Enable Bandwidth Limit – Check the box to define the

maximum speed of the data uploading/downloading which will

be used for the guest connecting to Vigor device with the same

SSID.

 Upload Limit – Scroll the radio button to choose the

value you want.

 Download Limit –Scroll the radio button to choose

the value you want.

Enable Station Control – Check the box to set the duration for

the guest connecting /reconnecting to Vigor device.

 Connection Time –Scroll the radio button to choose

the value you want.

 Reconnection Time –Scroll the radio button to

choose the value you want.

After finishing this web page configuration, please click Next to continue.

VigorAP 810 User’s Guide

-P

When you choose AP Bridge- Point to Point as Operation Mode and click Next, you will

need to configure the following page:

Available settings are explained as follows:

Item Description

AP Discovery Click this button to open the AP Discovery dialog. VigorAP

can scan all regulatory channels and find working APs in the

neighborhood.

Phy Mode Data will be transmitted via HTMIX communication channel.

Each access point should be setup to the same Phy mode for

connecting with each other.

Security Select WEP, TKIP or AES as the encryption algorithm. Type

the

key number if required.

Peer MAC Address Type the peer MAC address for the access point that VigorAP

810 connects to.

VigorAP 810 User’s Guide 20

-W

When you choose AP Bridge- WDS as Operation Mode and click Next, you will need to

configure the following page:

Available settings are explained as follows:

Item Description

AP Discovery Click this button to open the AP Discovery dialog. VigorAP

can scan all regulatory channels and find working APs in the

neighborhood.

Phy Mode Data will be transmitted via HTMIX communication channel.

Each access point should be setup to the same Phy mode for

connecting with each other.

Security Select WEP, TKIP or AES as the encryption algorithm. Type

the

key number if required. Or, you can click Disable to

disable the

function.

Peer MAC Address Type the peer MAC address for the access point that VigorAP

810 connects to.

Main SSID Set a name for VigorAP to be identified.

Security Key Type 8~63 ASCII characters, such as 012345678..(or 64

Hexadecimal digits leading by 0x, such as

"0x321253abcde...").

VigorAP 810 User’s Guide

When you choose Bridge-Universal Repeater as Operation Mode and click Next, you

will

need to configure the following page:

Available settings are explained as follows:

Item Description

Universal Repeater Parameters

AP Discovery Click this button to open the AP Discovery dialog. VigorAP

can scan all regulatory channels and find working APs in the

neighborhood.

SSID / MAC Address

(Optional) SSID means the identification of the wireless LAN. After

choosing one of the AP from AP Discovery window and

clicking OK, the settings (SSID and MAC Address) related to

the selected AP will be displayed on these fields automatically.

Later, VigorAP will be allowed to access Internet through the

selected AP, by using SSID displayed here.

Channel Means the channel frequency of the wireless LAN. The default

channel is 6. You may switch channel if the selected channel is

under serious interference.

Security Mode There are several modes provided for you to choose. Each

mode

will bring up different parameters (e.g., WEP keys, Pass

Phrase)

for you to configure.

VigorAP 810 User’s Guide 22

Encryption Type for

Open/Shared This option is available when Open/Shared is selected as

Security Mode.

Choose None to disable the WEP Encryption. Data sent to the

AP will not be encrypted. To enable WEP encryption for data

transmission, please choose WEP.

WEP Keys - Four keys can be entered here, but only one key

can be selected at a time. The format of WEP Key is restricted

5 ASCII characters or 10 hexadecimal values in 64-bit

encryption level, or restricted to 13 ASCII characters or 26

hexadecimal values in 128-bit encryption level. The allowed

content is the ASCII characters from 33(!) to 126(~) except '#'

and ','.

Encryption Type for

WPA/PSK and

WPA2/PSK

This option is available when WPA/PSK or WPA2/PSK is

selected as Security Mode.

Select TKIP or AES as the algorithm for WPA.

WEP Keys Four keys can be entered here, but only one key can be selected

at a time. The format of WEP Key is restricted to 5 ASCII

characters or 10 hexadecimal values in 64-bit encryption level,

or restricted to 13 ASCII characters or 26 hexadecimal values

128-bit encryption level. The allowed content is the ASCII

characters from 33(!) to 126(~) except '#' and ','.

Security Key Type 8~63 ASCII characters, such as 012345678..(or 64

Hexadecimal digits leading by 0x, such as

"0x321253abcde..."). Such feature is available for

WPA/PSK or WPA2/PSK mode.

Use the same SSID

and Security Key as

above

In general, under the network environment, same SSID and

security key can be used for the host (wireless client) and the

repeater (VigorAP) in Universal Repeater mode. Check it to

use the same SSID and security key configured as above.

SSID - SSID can be any text numbers or various special

characters. For VigorAP is set as “Repeater”, the purpose of

the device is to extend the Wi-Fi service. Therefore, the

characters set here will be regarded as “main SSID”. Other

wireless client can receive the wireless signal from VigorAP

by using the SSID configured here.

Security - Set 8~63 ASCII characters or 64 Hexadecimal digits

which can be used for logging into VigorAP by other wireless

VigorAP 810 User’s Guide

client.

Enable Guest

Wireless Check the box to enable the guest wireless setting.

SSID – Set a name for VigorAP. Wireless guest is allowed to

access into Internet via VigorAP with the SSID configured

here.

Security Key – Set 8~63 ASCII characters or 64 Hexadecimal

digits which can be used for logging into VigorAP by wireless

guest.

Enable Bandwidth Limit – Check the box to define the

maximum speed of the data uploading/downloading which will

be used for the guest connecting to Vigor device with the same

SSID.

 Upload Limit –Scroll the radio button to choose the

value you want.

 Download Limit –Scroll the radio button to choose

the value you want.

Enable Station Control – Check the box to set the duration

for the guest connecting /reconnecting to Vigor device.

 Connection Time –Scroll the radio button to

choose the value you want.

Reconnection Time –Scroll the radio button to choose the

value you want.

VigorAP 810 User’s Guide 24

When you see this page, it means the wireless setting wizard is almost finished. Just click

Finish to save the settings and complete the setting procedure.

VigorAP 810 User’s Guide

The online status shows the LAN status, Station Link Status for such device.

Detailed explanation is shown below:

Item Description

IP Address Displays the IP address of the LAN interface.

TX Packets Displays the total transmitted packets at the LAN interface.

RX Packets Displays the total number of received packets at the LAN

interface.

TX Bytes Displays the total transmitted size at the LAN interface.

RX Bytes Displays the total number of received size at the LAN interface.

VigorAP 810 User’s Guide 26

This page is left blank.

VigorAP 810 User’s Guide

This chapter will guide users to execute advanced (full) configuration.

1. Open a web browser on your PC and type http://192.168.1.2. The window will ask for

typing username and password.

2. Please type “admin/admin” on Username/Password for administration operation.

Now, the Main Screen will appear. Be aware that “Admin mode” will be displayed on the

bottom left side.

VigorAP 810 User’s Guide

all wireless clients within its coverage.

Note: The Wireless LAN settings will be changed according to the Operation Mode

selected here. For the detailed information, please refer to the section of Wireless LAN.

Local Area Network (LAN) is a group of subnets regulated and ruled by modem.

Click LAN to open the LAN settings page and choose General Setup.

Note: Such page will be changed according to the Operation Mode selected. The

following screen is obtained by choosing AP as the operation mode.

Available settings are explained as follows:

Item Description

LAN-A IP Network

Configuration Enable DHCP Client – When it is enabled, VigorAP will be

treated as a client and can be managed / controlled by AP

Management server offered by Vigor router (e.g., Vigor2860).

IP Address – Type in private IP address for connecting to a local

private network (Default: 192.168.1.2).

Subnet Mask – Type in an address code that determines the size

of the network. (Default: 255.255.255.0/ 24)

VigorAP 810 User’s Guide

server IP address here because your ISP often provides you

more than one DNS Server. If your ISP does not provide it,

the modem will automatically apply default secondary

DNS Server IP address: 194.98.0.1 to this field.

Relay Agent - Specify which subnet that DHCP server is located

the relay agent should redirect the DHCP request to.

 DHCP Server IP Address for Relay Agent - It is available

when Enable Relay Agent is selected. Set the IP address of

the DHCP server you are going to use so the Relay Agent

can help to forward the DHCP request to the DHCP server.

 Primary DNS Server - You must specify a DNS server IP

address here because your ISP should provide you with

usually more than one DNS Server. If your ISP does not

provide it, the modem will automatically apply default

DNS Server IP address: 194.109.6.66 to this field.

 Secondary DNS Server - You can specify secondary DNS

server IP address here because your ISP often provides you

more than one DNS Server. If your ISP does not provide it,

the modem will automatically apply default secondary

DNS Server IP address: 194.98.0.1 to this field.

Disable Server - Disable Server lets you manually or use other

DHCP server to assign IP address to every host in the LAN.

 Primary DNS Server - You must specify a DNS server IP

address here because your ISP should provide you with

usually more than one DNS Server. If your ISP does not

provide it, the modem will automatically apply default

DNS Server IP address: 194.109.6.66 to this field.

 Secondary DNS Server - You can specify secondary DNS

server IP address here because your ISP often provides you

more than one DNS Server. If your ISP does not provide it,

the modem will automatically apply default secondary

DNS Server IP address: 194.98.0.1 to this field.

 Trust DHCP Server IP for WLAN –There is no right for

such VigorAP to assign IP address for wireless LAN user.

However, you can specify another valid DHCP server on

other VigorAP to make the wireless LAN client obtaining

the IP address from the designated DHCP server.

Specify a DHCP server in such field. All the IP addresses

of the devices on LAN of VigorAP will be assigned via

such specified server. It is used to avoid IP assignment

interference due to multiple DHCP servers in one LAN.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide 32

This page allows you to configure a profile with specified URL for accessing into or display

a message when a wireless/LAN user connects to Internet through this router. No matter

what the purpose of the wireless/LAN client is, he/she will be forced into the URL

configured here while trying to access into the Internet or the desired web page through this

router. That is, a company which wants to have an advertisement for its products to users can

specify the URL in this page to reach its goal.

Each item is explained as follows:

Item Description

Index Display the number link which allows you to configure the

profile.

Enable Check the box to enable such profile.

Comments Display the content (Disable, URL Redirect or Message) of the

profile.

Interface Display the applied interfaces of the profile.

Preview Open a preview window according to the configured settings.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide

To configure the profile, click any index number link to open the following page.

Available settings are explained as follows:

Item Description

Enable Check the box to enable this function.

Comments Enter a brief comment to explain such web portal profile.

Welcome message Enter words or sentences here. The message will be displayed on

the screen for several seconds when the wireless users access

into the web page through the router.

 Default – Click it to restore the default content.

Redirect Page None - User can access into Internet directly.

URL Redirect - Any user who wants to access into Internet

through this router will be redirected to the URL specified here

first. It is a useful method for the purpose of advertisement. For

example, force the wireless user(s) in hotel to access into the

web page that the hotel wants the user(s) to visit.

Authentication None – User can access into Internet directly without

authentication.

Button Click – When a client tries to access into Internet, a

welcome message page with a button named “Accept” will

appear on the screen first. The client must click that button

(Accept) and then he/she is allowed to access Internet.

Applied Interfaces Check the box(es) representing different interfaces to be applied

by such profile.

 LAN – If it is selected and Universal Repeater is specified

as connection mode for such AP, both LAN client and

WLAN client can access into Internet via web portal. Yet,

if AP mode is selected, only wireless LAN client shall

VigorAP 810 User’s Guide 34

access into Internet via web portal.

 WLAN - The advantage is that each SSID (1/2/3/4) for

wireless network can be applied with different web portal

separately.

After finishing all the settings here, please click OK to save the configuration.

VigorAP 810 User’s Guide

Central AP Management allows you to configure VigorAP 810 to be managed by Vigor2860

series.

Available settings are explained as follows:

Item Description

Enable AP

Management Check the box to enable the function of AP Management.

Enable Auto

Provision VigorAP can be controlled under Central AP Management in

Vigor2860 series. When both Vigor2860 series and VigorAP

have such feature enabled, once VigorAP is registered to

Vigor2860 series, the WLAN profile pre-configured on

Vigor2860 series will be applied to VigorAP immediately. Thus,

it is not necessary to configure VigorAP separately.

VigorAP 810 User’s Guide

apply the AP Load Balancing to the multiple APs will manage wireless traffic with smooth

flow and enhanced efficiency.

Load Balance can help to distribute the traffic for all of the access points (e.g., VigorAP)

registered to Vigor router. Thus, the bandwidth will not be occupied by certain access points.

However, traffic overload might be occurred if too many wireless stations connected to

VigorAP for data incoming and outgoing. Therefore, “Force Overload Disassociation” is

required to terminate the network connection of the client’s station to release network traffic.

When the function of “Force Overload Disassociation” in web user interface of Vigor router

(e.g., Vigor2860 or Vigor2925 series) is enabled, wireless clients specified in black list of

such web page will be disassociated to solve the problem of traffic overload.

The following web page is used to configure white list and black list for wireless stations.

Available settings are explained as follows:

Item Description

White List/Black List Display the information (such as index number, MAC address

and comment) for all of the members in White List/Black List.

Wireless stations listed in Black List will be forcefully

disconnected first when traffic overload occurs and “Force

Overload Disassociation” is enabled.

Client’s MAC

Address Specify the MAC Address of the remote/local client.

Apply to White List – MAC address listed inside Client’s MAC Address

will be categorized as one of members in White List.

Black List - MAC address listed inside Client’s MAC Address

will be categorized as one of members in Black List.

VigorAP 810 User’s Guide 38

Comment Type any words as notification.

Add Add a new MAC address into the White List/Black List.

Delete Delete the selected MAC address in the White List/Black List.

Edit Edit the selected MAC address in the White List/Black List.

Cancel Give up the configuration.

Load Balance can help to distribute the traffic for all of the access points (e.g., VigorAP)

registered to Vigor2860 or Vigor2925 series. This web page displays the settings related to

Load Balance for VigorAP. In which, By Station Number, By Traffic and Force Overload

Disassociation indicate settings configured in Vigor 2860 or Vigor2925 series.

Below shows a setting example for Load Balance settings configured in Vigor 2860 or

Vigor2925 series.

VigorAP 810 User’s Guide

The VigorAP 810 is equipped with a wireless LAN interface compliant with the standard

IEEE 802.11n draft 2 protocol. To boost its performance further, the VigorAP 810 is also

loaded with advanced wireless technology to lift up data rate up to 300 Mbps*. Hence, you

can finally smoothly enjoy stream music and video.

Note: * The actual data throughput will vary according to the network conditions and

environmental factors, including volume of network traffic, network overhead and

building materials.

In an Infrastructure Mode of wireless network, VigorAP 810 plays a role as an Access Point

(AP) connecting to lots of wireless clients or Stations (STA). All the STAs will share the

same Internet connection via VigorAP 810. The General Setup will set up the information

of this wireless network, including its SSID as identification, located channel etc.

WEP (Wired Equivalent Privacy) is a legacy method to encrypt each frame transmitted via

radio using either a 64-bit or 128-bit key. Usually access point will preset a set of four keys

and it will communicate with each station using only one out of the four keys.

WPA (Wi-Fi Protected Access), the most dominating security mechanism in industry, is

separated into two categories: WPA-personal or called WPA Pre-Share Key (WPA/PSK),

and WPA-Enterprise or called WPA/802.1x.

In WPA-Personal, a pre-defined key is used for encryption during data transmission. WPA

applies Temporal Key Integrity Protocol (TKIP) for data encryption while WPA2 applies

AES. The WPA-Enterprise combines not only encryption but also authentication.

Since WEP has been proved vulnerable, you may consider using WPA for the most secure

connection. You should select the appropriate security mechanism according to your needs.

No matter which security suite you select, they all will enhance the over-the-air data

protection and /or privacy on your wireless network. The VigorAP 810 is very flexible and

can support multiple secure connections with both WEP and WPA at the same time.

WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection

between wireless station and wireless access point (VigorAP 810) with the encryption of

WPA and WPA2.

It is the simplest way to build connection between wireless network clients and VigorAP 810.

Users do not need to select any encryption mode and type any long encryption passphrase to

setup a wireless client every time. He/she only needs to press a button on wireless client, and

WPS will connect for client and VigorAP 810 automatically.

VigorAP 810 User’s Guide 40

Note: Such function is available for the wireless station with WPS supported.

There are two methods to do network connection through WPS between AP and Stations:

pressing the Start PBC button or using PIN Code.

On the side of VigorAP 810 series which served as an AP, press WPS button once on the

front panel of VigorAP 810 or click Start PBC on web configuration interface. On the side

of a station with network card installed, press Start PBC button of network card.

If you want to use PIN code, you have to know the PIN code specified in wireless client.

Then provide the PIN code of the wireless client you wish to connect to the VigorAP 810.

VigorAP 810 User’s Guide

When you choose AP as the operation mode, the Wireless LAN menu items will include

General Setup, Security, Access Control, WPS, Advanced Setting, AP Discovery, WMM

Configuration, Bandwidth Management, Airtime Fairness, Station Control, Roaming, and

Station List.

Note: The Wireless LAN settings will be changed according to the Operation Mode

selected in section 3.1.

VigorAP 810 User’s Guide 42

By clicking the General Setup, a new web page will appear so that you could configure the

SSID and the wireless channel. Please refer to the following figure for more information.

Available settings are explained as follows:

Item Description

Enable Wireless LAN Check the box to enable wireless function.

Enable Client Limit Check the box to set the maximum number of wireless stations

which try to connect Internet through Vigor AP. The number

you can set is from 3 to 64.

Enable Client Limit

per SSID Define the maximum number of wireless stations per SSID

which try to connect to Internet through Vigor device. The

number you can set is from 3 to 64.

Mode At present, VigorAP 810 can connect to 11b only, 11g only,

11n only, Mixed (11b+11g), Mixed (11g+11n) and Mixed

(11b+11g+11n) stations simultaneously. Simply choose Mixed

(11b+11g+11n) mode.

VigorAP 810 User’s Guide

Channel Means the channel of frequency of the wireless LAN. You may

switch channel if the selected channel is under serious

interference. If you have no idea of choosing the frequency,

please select AutoSelect to let system determine for you.

Extension Channel With 802.11n, there is one option to double the bandwidth per

channel. The available extension channel options will be varied

according to the Channel selected above. Configure the

extension channel you want.

Enable 2 Subnet

(Simulate 2 APs) Check the box to enable the function for two independent

subnets. Once you enable this function, LAN-A and LAN-B

would be independent. Next, you can connect one router in

LAN-A, and another router in LAN-B. Such mechanism can

make you feeling that you have two independent AP/subnet

functions in one VigorAP 810.

If you disable this function, LAN-A and LAN-B ports are in

the same domain. You could only connect one router (no

matter connecting to LAN-A or LAN-B) in this environment.

Enable SSID #1 is enabled in default. SSID #2 ~ #4 can be enabled

manually.

Hide SSID Check it to prevent from wireless sniffing and make it harder

for unauthorized clients or STAs to join your wireless LAN.

Depending on the wireless utility, the user may only see the

information except SSID or just cannot see any thing about

VigorAP 810 while site surveying. The system allows you to

set three sets of SSID for different usage.

SSID Set a name for VigorAP 810 to be identified. Default settings

are DrayTek-LAN-A and DrayTek-LAN-B. When Enable 2

Subnet is enabled, you can specify subnet interface (LAN-A

or LAN-B) for each SSID by using the drop down menu.

Subnet Choose LAN-A or LAN-B for each SSID. If you choose

LAN-A, the wireless clients connecting to this SSID could

only communicate with LAN-A.

Isolate Member Check this box to make the wireless clients (stations) with the

same SSID not accessing for each other.

VLAN ID Type the value for such SSID. Packets transferred from such

SSID to LAN will be tagged with the number.

If your network uses VLANs, you can assign the SSID to a

VLAN on your network. Client devices that associate using the

SSID are grouped into this VLAN. The VLAN ID range is

from 3 to 4095. The VLAN ID is 0 by default, it means

disabling the VLAN function for the SSID.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide 44

This page allows you to set security with different modes for SSID 1, 2, 3 and 4 respectively.

After configuring the correct settings, please click OK to save and invoke it.

By clicking the Security Settings, a new web page will appear so that you could configure

the settings.

Available settings are explained as follows:

Item Description

Mode There are several modes provided for you to choose.

Disable - The encryption mechanism is turned off.

WEP - Accepts only WEP clients and the encryption key

should be entered in WEP Key.

WPA/PSK or WPA2/PSK or Mixed (WPA+WPA2)/PSK -

Accepts only WPA clients and the encryption key should be

entered in PSK. The WPA encrypts each frame transmitted

from the radio using the key, which either PSK (Pre-Shared

Key) entered manually in this field below or automatically

negotiated via 802.1x authentication.

VigorAP 810 User’s Guide

WEP/802.1x - The built-in RADIUS client feature enables

VigorAP 810 to assist the remote dial-in user or a wireless

station and the RADIUS server in performing mutual

authentication. It enables centralized remote access

authentication for network management.

The WPA encrypts each frame transmitted from the radio

using the key, which either PSK (Pre-Shared Key) entered

manually in this field below or automatically negotiated via

802.1x authentication. Select WPA, WPA2 or Auto as WPA

mode.

WPA/802.1x - The WPA encrypts each frame transmitted

from the radio using the key, which either PSK (Pre-Shared

Key) entered manually in this field below or automatically

negotiated via 802.1x authentication.

WPA2/802.1x - The WPA encrypts each frame transmitted

from the radio using the key, which either PSK (Pre-Shared

Key) entered manually in this field below or automatically

negotiated via 802.1x authentication.

WPA Algorithms Select TKIP, AES or TKIP/AES as the algorithm for WPA.

Such feature is available for WPA2/802.1x, WPA/802.1x,

WPA/PSK or WPA2/PSK or Mixed (WPA+WPA2)/PSK

mode.

Pass Phrase Either 8~63 ASCII characters, such as 012345678..(or 64

Hexadecimal digits leading by 0x, such as

"0x321253abcde..."). Such feature is available for WPA/PSK

or WPA2/PSK or Mixed (WPA+WPA2)/PSK mode.

Key Renewal Interval WPA uses shared key for authentication to the network.

However, normal network operations use a different

encryption key that is randomly generated. This randomly

generated key that is periodically replaced. Enter the renewal

security time (seconds) in the column. Smaller interval leads to

greater security but lower performance. Default is 3600

seconds. Set 0 to disable re-key. Such feature is available for

WPA2/802.1,WPA/802.1x, WPA/PSK or WPA2/PSK or

Mixed (WPA+WPA2)/PSK mode.

EAPOL Key Retry EAPOL means Extensible Authentication Protocol over LAN.

Enable - The default setting is "Enable". It can make sure that

the key will be installed and used once in order to prevent key

reinstallation attack.

Key 1 – Key 4 Four keys can be entered here, but only one key can be

selected at a time. The format of WEP Key is restricted to 5

ASCII characters or 10 hexadecimal values in 64-bit

encryption level, or restricted to 13 ASCII characters or 26

hexadecimal values in 128-bit encryption level. The allowed

content is the ASCII characters from 33(!) to 126(~) except '#'

and ','. Such feature is available for WEP mode.

VigorAP 810 User’s Guide 46

802.1x WEP Disable - Disable the WEP Encryption. Data sent to the AP

will not be encrypted.

Enable - Enable the WEP Encryption.

Such feature is available for WEP/802.1x mode.

Click the link of RADIUS Server to access into the following page for more settings.

Available settings are explained as follows:

Item Description

Use internal RADIUS

Server There is a RADIUS server built in VigorAP 810 which is used

to authenticate the wireless client connecting to the access

point. Check this box to use the internal RADIUS server for

wireless security.

Besides, if you want to use the external RADIUS server for

authentication, do not check this box.

Please refer to the section, 3.10 RADIUS Setting to configure

settings for internal server of VigorAP 810.

IP Address Enter the IP address of external RADIUS server.

Port The UDP port number that the external RADIUS server is

using. The default value is 1812, based on RFC 2138.

Shared Secret The external RADIUS server and client share a secret that is

used to authenticate the messages sent between them. Both

sides must be configured to use the same shared secret.

Session Timeout Set the maximum time of service provided before

re-authentication. Set to zero to perform another authentication

immediately after the first authentication has successfully

completed. (The unit is second.)

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide

setup WPS within two minutes).

This page is to determine which algorithm will be selected for wireless transmission rate.

Available settings are explained as follows:

Item Description

Channel Width 20 MHZ- the AP will use 20MHz for data transmission and

receiving between the AP and the stations.

Auto 20/40 MHZ– the AP will scan for nearby wireless AP,

and then use 20MHz if the number of AP is more than 10, or

use 40MHz if it's not.

40 MHZ- the AP will use 40MHz for data transmission and

receiving between the AP and the stations.

Packet-OVERDRIVE This feature can enhance the performance in data transmission

about 40%* more (by checking Tx Burst). It is active only

when both sides of Access Point and Station (in wireless

client) invoke this function at the same time. That is, the

wireless client must support this feature and invoke the

function, too.

Note: Vigor N61 wireless adapter supports this function.

Therefore, you can use and install it into your PC for matching

with Packet-OVERDRIVE (refer to the following picture of

Vigor N61 wireless utility window, choose Enable for

TxBURST on the tab of Option).

VigorAP 810 User’s Guide 50

Antenna VigorAP can be attached with two antennas to have good data

transmission via wireless connection. However, if you have

only one antenna attached, please choose 1T1R.

Tx Power The default setting is the maximum (100%). Lowering down

the value may degrade range and throughput of wireless.

Rate Adaptation

Algorithm Wireless transmission rate is adapted dynamically. Usually,

performance of “new” algorithm is better than “old”.

Fragment Length Set the Fragment threshold of wireless radio. Do not modify

default value if you don’t know what it is, default value is

2346.

RTS Threshold Minimize the collision (unit is bytes) between hidden stations

to improve wireless performance.

Set the RTS threshold of wireless radio. Do not modify default

value if you don’t know what it is, default value is 2347.

Country Code VigorAP broadcasts country codes by following the 802.11d

standard. However, some wireless stations will detect / scan

the country code to prevent conflict occurred. If conflict is

detected, wireless station will be warned and is unable to make

network connection. Therefore, changing the country code to

ensure successful network connection will be necessary for

some clients.

Auto Channel

Filtered Out List The selected wireless channels will be discarded if AutoSelect

is selected as Channel selection mode in Wireless

LAN>>General Setup.

IGMP Snooping Check Enable to enable IGMP Snooping. Multicast traffic will

be forwarded to ports that have members of that group.

Disabling IGMP snooping will make multicast traffic treated in

the same manner as broadcast traffic.

Isolate members with

IP The default setting is “Disable”.

If it is enabled, VigorAP will isolate different wireless clients

according to their IP address(es).

VigorAP 810 User’s Guide

MAC Clone Click Enable and manually enter the MAC address of the

device with SSID 1. The MAC address of other SSIDs will

change based on this MAC address.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 can scan all regulatory channels and find working APs in the neighborhood.

Based on the scanning result, users will know which channel is clean for usage. Also, it can

be used to facilitate finding an AP for a WDS link. Notice that during the scanning process

(about 5 seconds), no client is allowed to connect to Vigor.

This page is used to scan the existence of the APs on the wireless LAN. Please click Scan to

discover all the connected APs.

Each item is explained as follows:

Item Description

Enable AP Monitor

Mode This function can help to get and keep the records of APs

detected by such device after clicking Scan.

In general, only the available AP will be detected by Vigor

device. Once the AP is unavailable, it will be deleted from the

Access Point List immediately. However, if such function is

enabled, the system will keep the record of the AP (once

detected by Vigor device) until it is available for Vigor device

again.

SSID Display the SSID of the AP scanned by VigorAP 810.

BSSID Display the MAC address of the AP scanned by VigorAP 810.

RSSI Display the signal strength of the access point. RSSI is the

abbreviation of Receive Signal Strength Indication.

Channel Display the wireless channel used for the AP that is scanned by

VigorAP 810.

VigorAP 810 User’s Guide 52

Encryption Display the encryption mode for the scanned AP.

Authentication Display the authentication type that the scanned AP applied.

Mode Display the wireless connection mode that the scanned AP

used.

Ch. Width Display the channel width that the scanned AP used.

Scan It is used to discover all the connected AP. The results will be

shown on the box above this button

Channel Statistics It displays the statistics for the channels used by APs.

WMM is an abbreviation of Wi-Fi Multimedia. It defines the priority levels for four access

categories derived from 802.1d (prioritization tabs). The categories are designed with

specific types of traffic, voice, video, best effort and low priority data. There are four

accessing categories - AC_BE , AC_BK, AC_VI and AC_VO for WMM.

Available settings are explained as follows:

Item Description

WMM Capable To apply WMM parameters for wireless data transmission,

please click the Enable radio button.

Aifsn It controls how long the client waits for each data transmission.

Please specify the value ranging from 1 to 15. Such parameter

will influence the time delay for WMM accessing categories.

For the service of voice or video image, please set small value

for AC_VI and AC_VO categories For the service of e-mail or

web browsing, please set large value for AC_BE and AC_BK

categories.

CWMin/CWMax CWMin means contention Window-Min and CWMax means

contention Window-Max. Please specify the value ranging from

1 to 15. Be aware that CWMax value must be greater than

CWMin or equals to CWMin value. Both values will influence

the time delay for WMM accessing categories. The difference

VigorAP 810 User’s Guide 54

The downstream or upstream from FTP, HTTP or some P2P applications will occupy large

of bandwidth and affect the applications for other programs. Please use Bandwidth

Management to make the bandwidth usage more efficient.

Available settings are explained as follows:

Item Description

SSID Display the specific SSID name of the AP.

Enable Check this box to enable the bandwidth management for clients.

Upload Limit Define the maximum speed of the data uploading which will be

used for the wireless stations connecting to Vigor AP with the

same SSID.

Use the drop down list to choose the rate. If you choose User

defined, you have to specify the rate manually.

Download Limit Define the maximum speed of the data downloading which will

be used for the wireless station connecting to Vigor AP with the

same SSID.

Use the drop down list to choose the rate. If you choose User

defined, you have to specify the rate manually.

Auto Adjustment Check this box to have the bandwidth limit determined by the

system automatically.

Total Upload Limit When Auto Adjustment is checked, the value defined here will

be treated as the total bandwidth shared by all of the wireless

stations with the same SSID for data uploading.

Total Download

Limit When Auto Adjustment is checked, the value defined here will

be treated as the total bandwidth shared by all of the wireless

stations with the same SSID for data downloading.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide

Airtime fairness is essential in wireless networks that must support critical enterprise

applications.

Most of the applications are either symmetric or require more downlink than uplink capacity;

telephony and email send the same amount of data in each direction, while video streaming

and web surfing involve more traffic sent from access points to clients than the other way

around. This is essential for ensuring predictable performance and quality-of-service, as well

as allowing 802.11n and legacy clients to coexist on the same network. Without airtime

fairness, offices using mixed mode networks risk having legacy clients slow down the entire

network or letting the fastest client(s) crowd out other users.

With airtime fairness, every client at a given quality-of-service level has equal access to the

network's airtime.

The wireless channel can be accessed by only one wireless station at the same time.

The principle behind the IEEE802.11 channel access mechanisms is that each station has

equal probability to access the channel. When wireless stations have similar data rate, this

principle leads to a fair result. In this case, stations get similar channel access time which is

called airtime.

However, when stations have various data rate (e.g., 11g, 11n), the result is not fair. The

slow stations (11g) work in their slow data rate and occupy too much airtime, whereas the

fast stations (11n) become much slower.

Take the following figure as an example, both Station A(11g) and Station B(11n) transmit

data packets through VigorAP 810. Although they have equal probability to access the

wireless channel, Station B(11n) gets only a little airtime and waits too much because Station

A(11g) spends longer time to send one packet. In other words, Station B(fast rate) is

obstructed by Station A(slow rate).

To improve this problem, Airtime Fairness is added for VigorAP 810. Airtime Fairness

function tries to assign similar airtime to each station (A/B) by controlling TX traffic. In the

following figure, Station B(11n) has higher probability to send data packets than Station

A(11g). By this way, Station B(fast rate) gets fair airtime and it's speed is not limited by

Station A(slow rate).

VigorAP 810 User’s Guide 56

It is similar to automatic Bandwidth Limit. The dynamic bandwidth limit of each station

depends on instant active station number and airtime assignment. Please note that Airtime

Fairness of 2.4GHz and 5GHz are independent. But stations of different SSIDs function

together, because they all use the same wireless channel. IN SPECIFIC ENVIRONMENTS,

this function can reduce the bad influence of slow wireless devices and improve the overall

wireless performance.

Suitable environment:

(1) Many wireless stations.

(2) All stations mainly use download traffic.

(3) The performance bottleneck is wireless connection.

Available settings are explained as follows:

Item Description

Enable Airtime

Fairness Try to assign similar airtime to each wireless station by

controlling TX traffic.

Airtime Fairness – Click the link to display the following

screen of airtime fairness note.

Triggering Client Number –Airtime Fairness function is

applied only when active station number achieves this number.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide

Note: Airtime Fairness function and Bandwidth Limit function should be mutually

exclusive. So their webs have extra actions to ensure these two functions are not enabled

simultaneously.

Station Control is used to specify the duration for the wireless client to connect and

reconnect VigorAP. If such function is not enabled, the wireless client can connect VigorAP

until it shuts down.

Such feature is especially useful for free Wi-Fi service. For example, a coffee shop offers

free Wi-Fi service for its guests for one hour every day. Then, the connection time can be set

as “1 hour” and reconnection time can be set as “1 day”. Thus, the guest can finish his job

within one hour and will not occupy the wireless network for a long time.

Note: Up to 300 Wireless Station records are supported by VigorAP.

Available settings are explained as follows:

Item Description

SSID Display the SSID that the wireless station will use it to

connect with Vigor router.

Enable Check the box to enable the station control function.

Connection Time /

Reconnection Time Use the drop down list to choose the duration for the

wireless client connecting /reconnecting to Vigor router. Or,

type the duration manually when you choose User defined.

Display All Station

Control List All the wireless stations connecting to Vigor router by using

such SSID will be listed on Station Control List.

VigorAP 810 User’s Guide

over) is detected by VigorAP 810, VigorAP 810 will terminate

the network connection for that wireless station. Later, the

wireless station can connect to the adjacent AP (with better

RSSI).

 With Adjacent AP RSSI over – Specify a value as a

threshold.

Fast Roaming

(WPA/802.1x) Enable – Check the box to enable fast roaming configuration.

PMK Cache Period - Set the expire time of WPA2 PMK

(Pairwise master key) cache. PMK Cache manages the list from

the BSSIDs in the associated SSID with which it has

pre-authenticated. Such feature is available for WPA2/802.1

mode.

Pre-Authentication - Enables a station to authenticate to

multiple APs for roaming securer and faster. With the

pre-authentication procedure defined in IEEE 802.11i

specification, the pre-four-way-handshake can reduce handoff

delay perceivable by a mobile node. It makes roaming faster and

more secure. (Only valid in WPA2)

Enable - Enable IEEE 802.1X Pre-Authentication.

Disable - Disable IEEE 802.1X Pre-Authentication.

After finishing this web page configuration, please click OK to save the settings.

VigorAP 810 User’s Guide 60

Station List provides the knowledge of connecting wireless clients now along with its status

code. Each tab (general, advanced, control, neighbor) will display different status

information (including MAC address, Vendor, SSID, Auth, Encrypt, Tx/Rx Rate, Hostname,

RSSI, Link Speed, BW, PSM, WMM, PHMd, MCS, Connection Time, Reconnection Time,

Approx. Distance, Visit Time, and so on)

Available settings are explained as follows:

Item Description

MAC Address Display the MAC Address for the connecting client.

SSID Display the SSID that the wireless client connects to.

Auth Display the authentication that the wireless client uses for

connection with such AP.

Encrypt Display the encryption mode used by the wireless client.

Tx Rate/Rx Rate Display the transmission /receiving rate for packets.

Refresh Click this button to refresh the status of station list.

Add to Access

Control Client’s MAC Address - For additional security of wireless

access, the Access Control facility allows you to restrict the

network access right by controlling the wireless LAN MAC

address of client. Only the valid MAC address that has been

configured can access the wireless LAN interface.

Add Click this button to add current typed MAC address into

Access Control.

General

Display general information (e.g., MAC Address, SSID, Auth, Encrypt, TX/RX Rate) for the

station.

Advanced

VigorAP 810 User’s Guide

Display more information (e.g., AID, PSM, WMM, RSSI PhMd, BW, MCS, Rate) for the

station.

Control

Display connection and reconnection time of the wireless stations.

Neighbor

Display more information for the neighboring wireless stations.

VigorAP 810 User’s Guide 62

Wireless LAN Settings for Station-Infrastructure Mode

When you choose Station-Infrastructure as the operation mode, the Wireless LAN menu

items will include General Setup, Site Survey, Statistics and WPS.

By clicking the General Setup, a new web page will appear so that you could configure the

wireless profile and choose proper mode. Please refer to the following figure for more

information.

Available settings are explained as follows:

Item Description

Enable Wireless LAN Check the box to enable wireless function.

Mode At present, VigorAP 810 can connect to 11 b only, 11 g only,

n only, Mixed (11b+11g), Mixed (11b+11g+11n) and

Mixed

(11g+11n) stations simultaneously. Simply choose

Mixed

(11b+11g+11n) mode.

Add Click this button to add new wireless profiles.

Delete Click this button to delete the selected wireless profile.

Edit Click this button to modify the existing wireless profile.

Connect Click this button to connect the wireless station to AP with the

selected profile.

VigorAP 810 User’s Guide

Packet-OVERDRIVE This feature can enhance the performance in data transmission

about 40%* more (by checking Tx Burst). It is active only

when

both sides of Access Point and Station (in wireless

client) invoke

this function at the same time. That is, the

wireless client must

support this feature and invoke the

function, too.

Note: Vigor N61 wireless adapter supports this function.

Therefore, you can use and install it into your PC for matching

with Packet-OVERDRIVE (refer to the following picture of

Vigor N61 wireless utility window, choose Enable for

TxBURST on the tab of Option).

MAC Clone Check this box and manually enter the MAC address for

Station

mode driver.

After finishing this web page configuration, please click OK to save the settings.

To add a new wireless profile for the stations, click Add. The following dialog box will

appear.

VigorAP 810 User’s Guide 66

There are two types of key method: ASCII and Hex. When

you

select a key format, the number of characters of key will

displayed. For example, if you select 64-bit as key length,

and

Hex as key format, you’ll see the message at the right of

Key

Format is ‘Hex (10 characters) which means the length of

WEP key is 10 characters.

WEP Keys (Key 1 – Key 4) - Four keys can be entered here,

but only one key can be selected at a time. The format of WEP

Key is restricted to 5 ASCII characters or 10 hexadecimal

values in 64-bit encryption level, or restricted to 13 ASCII

characters or 26 hexadecimal values in 128-bit encryption

level. The allowed content is the ASCII characters from 33(!)

to 126(~) except '#' and ','. Such feature is available for WEP

mode.

Default Key – Choose one of the key settings.

Below shows an example for a wireless profile created.

VigorAP 810 User’s Guide 70

-P

When you choose AP Bridge-Point to Point or Point-to Multi-Point Mode as the operation

mode, the Wireless LAN menu items will include General Setup, Advanced Setting, AP

Discovery and WDS AP Status.

AP Bridge-Point to Point allows VigorAP 810 to connect to another VigorAP 810 which

uses the same mode. All wired Ethernet clients of both VigorAP 810s will be connected

together.

Point-to Multi-Point Mode allows AP 810 to connect up to four AP 810s which uses the

same mode. All wired Ethernet clients of every VigorAP 810 will be connected together.

By clicking the General Setup, a new web page will appear so that you could configure the

Phy mode, security, Tx Burst and choose proper mode. Please refer to the following figure

for more information.

Available settings are explained as follows:

Item Description

Enable Wireless LAN Check the box to enable wireless function.

Mode At present, VigorAP 810 can connect to 11b only, 11g only,

11n only, Mixed (11b+11g), Mixed (11g+11n) and Mixed

(11b+11g+11n) stations simultaneously. Simply choose

Produkt Specifikationer

Mærke:	Draytek
Kategori:	Wifi
Model:	Vigor AP 810

Har du brug for hjælp?

Hvis du har brug for hjælp til Draytek Vigor AP 810 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Wifi Draytek Manualer

Draytek Vigor AP 902 Manual

22 September 2024

Draytek Vigor AP 903 Manual

19 Juli 2024

Draytek Vigor AP 810 Manual

18 Juli 2024

Wifi Manualer

Nyeste Wifi Manualer

Gembird UHB-U2P7-03 Manual

7 Februar 2025

Tenda PH6 Manual

15 Januar 2025

ICIDU NI - 707547 Manual

13 Januar 2025

AVM Fritz Powerline 1240E Manual

11 Januar 2025

Gembird WNP-UA-005 Wifi Manual

11 September 2024

Gembird WNP-RP-002-B Wifi Manual

11 September 2024

Gembird WP-L-02 Wifi Manual

10 September 2024

Easypix 3G Dongle for EasyPad 1200 Manual

26 August 2024

DKT WAVE 2 AIR Manual

26 August 2024

Netgear EX3920 - AC750 WiFi Range Extender Manual

26 August 2024