Drayton miGenie Wish 3 Manual

Drayton Smart hjem miGenie Wish 3

Læs gratis den danske manual til Drayton miGenie Wish 3 (2 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Drayton miGenie Wish 3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Step 1: Mounting the Wall-plate

! IMPORTANT:

Installation must only be carried out by a

qualiﬁed electrician or heating engineer.

Make sure mains input has a 3 amp fuse.

! CAUTION! Before installation, make sure the

mains supply is switched off!

Option 1: Fitting a new wall-plate

The ideal location is 1.2m above

ﬂoor level, with reasonable

lighting, good access, no

condensation, no extremes of

temperature and a supporting

surface that fully covers the

back of the unit. Position with

70mm clearance to the right,

25mm above and sufﬁcient room

to access the securing screws

underneath. Fix, with terminals

at the top, either direct to a ﬂat

wall using wall plugs and No. 6 x

1” (25mm) woodscrews, or on a

ﬂush mounting single conduit box

type UA1 (BS4662) using M3.5 x

14 bolts. Check the 3A fuse, and

switch on the mains.

! DO NOT use a surface mounting box

→

Option 2: Using an existing

industry standard wall-plate

Loosen the securing screws

on the old programmer and

unplug it. Check that there is

70mm clearance to the right of

the wall-plate and 25mm above

it. Check the wiring diagram for

your product model to compare

terminals and, if necessary,

change the wiring of the wall-

plate to suit. Now ﬁt the miGenie

controller into the wall-plate and

tighten the securing screws.

Check the 3A fuse, and switch on

the mains.

Wireless Packs

Technical elpline: H 0333 7000 62 2

Website: www.draytoncontrols.co.uk

www.mi-genie.co.uk

E-mail: customer.care@draytoncontrols.co.uk

@DraytonControls

/DraytonControls

EU Design Regs

:- 002180638-1/2/3

Installer uide 6490211001 ss G 0 I D

INSTALLATION Guide

Single Channel : miGenie Wish 1 T714R

Dual Channel: miGenie Wish 2 T724R

Multi Channel: miGenie Wish 3 T744R

Step 2: Wiring

→

Step 3: continued...

Step 4: Signal Strength

Step 5: Mounting Options

Step 6: Install the miGenie Gateway & miGenie app

→ →

→

The miGenie thermostat(s) & miGenie gateway are

pre-bound to the miGenie controller in the factory so

they just need to be positioned in the best place for

wireless communication. To help with this there is a

built in signal strength indicator, available in the Zone

Settings menu on the miGenie controller, as shown.

It is recommended that the signal strength is Good or

Very Good to ensure communication is maintained.

The signal strength can also be seen on the miGenie

thermostat.

To enter the Signal Strength menu

• Press + & - for approx. 5 secs, then scroll (+/-) to show

10. ADV-SET,

• Press (

) to enter the Advanced Settings menu,

• Press +/- until 19 WIRELESS is shown,

• Press ( ) to enter the Wireless menu,

• Press +/- to show 21 SIG-LEVEL as shown,

• Press ( ) to see the current signal strength.

miGenie thermostat rear

Battery Covers:

Slide outwards

to remove

Once the best position has been identiﬁed, the

miGenie thermostat should be ﬁxed to the wall using

the wall bracket as shown.

Location & Wiring

The miGenie gateway is designed to be placed

on a ﬂat surface and should be located next to the

customer’s internet router. A short ethernet cable is

provided to connect the miGenie gateway to a spare

LAN port on the back of the internet router (see

image below).

Creating a User Account

Note: You can only create a User Account when your

miGenie Wireless Pack has been fully installed.

You will ﬁrst need to download the Drayton miGenie

app for your smartphone or tablet which is available

from the App Store or Google Play.

The app guides you through the registration process

which connects your miGenie system to your e-mail

address. During this process you will be asked to

press the button on the back of the miGenie gateway

which will ﬂash green until the connection is made.

A veriﬁcation e-mail will be sent to you to conﬁrm

your e-mail address before the app can be used.

Once the gateway has been registered the system

is ready to control your heating and hot water.

To control your miGenie system from additional

smartphones or tablets simply download and install

the app and login using the same e-mail address

and password.

NB. miGenie thermostat can also be positioned using

the table stand included.

The miGenie gateway is powered from a standard

mains wall socket using the supplied adaptor plug.

Care should be taken to mount the miGenie thermostat

in a position which is not subject to direct sunlight or

draughts. Preferably it should be mounted on an inside

wall about 1.2m (4ft) above the ﬂoor in a position where

it can respond to room temperature but away from the

direct inﬂuence of radiators or other appliances giving

off heat.

Status

The miGenie gateway reports status information

on the LED located on the rear of the product.

An overview of the status information is given in the

table below:

Connect the wiring as shown above.

T714R only: Note that the output contacts are

voltage-free, so power needs to be put on to

Terminal 1 either by linking from Terminal L or

from a separate supply with a 3A fuse.

! IMPORTANT:

Always switch off the mains before removing

the miGenie controller and never ﬁt it to a live

wall-plate!

eg.

It has to be placed in a location where it will be able to

control the room temperature.

If POOR is displayed, look for a better location

If NO SIGNAL is displayed, try connecting again with

the room unit in a different position. To exit, press + &

- keys for approx. 5 seconds. If there is no key pressed

for 2 minutes, the menu will be exited automatically.

1.2m

1 2 3

LAN

WAN

LED State

(During Setup)

Activity

Cycling through Red,

Amber, Green

The miGenie gateway is attempting

to bind to a miGenie Controller.

Can be started manually by

pressing and holding the gateway

button for 5 seconds.

Off Indicates that either;

- the miGenie gateway is not

connected to the miGenie controller.

- the miGenie gateway has not been

registered with an internet account

and app.

Green ﬂashing every

1 second

This occurs when the button on the

rear of the gateway is pressed. The

miGenie gateway is attempting to

connect to a miGenie app via the

internet. This mode will time out

after 5 minutes.

LED State (During

normal use)

Activity

Green Indicates 'all OK' – the gateway is

connected to the miGenie controller

and internet control is available.

Solid Red No RF signal – the device should

be relocated closer to the miGenie

controller.

Solid Amber No internet connection – check the

status of the local internet router

and all cabling.

Single Channel:

miGenie T714R

Dual Channel:

miGenie T724R

Multi Channel:

miGenie T744R

Ch1 Ch2 Ch3 Ch4

Step 3:

miGenie Thermostats

- Checking the batteries

How do I know when to change

the batteries?

When the batteries start to run low a battery icon

will ﬂash in the display, to indicate “low battery”

during this time the miGenie thermostat will function

normally. Please replace batteries with 2 x 1.5V

IEC LR6 (AA) Alkaline batteries. When the battery

icon alone is shown in the display, the batteries are

completely exhausted and the miGenie thermostat

will cease to function (see below).

Re-activate by replacing the batteries.

Battery Handling

Batteries, rechargeable or not, should not be disposed

of into ordinary household waste. Instead, they must be

recycled properly to protect the environment and cut

down the waste of precious resources.

Your local waste management authority can supply

details concerning the proper disposal of batteries.

In compliance with the EU Directive 2006/66/EC, the

button cell battery located on the printed circuit board

inside the product, can be removed at the end of the

product life, by professional personnel only.

How to replace the batteries

Remove the battery covers as shown. Replace the

spent batteries with 2 x 1.5V IEC LR6 (AA) Alkaline

batteries ensuring correct orientation. Replace the

battery covers pressing fully home.

Drayton

401 Southway Drive

Plymouth

PL6 6QT

United Kingdom

Produkt Specifikationer

Mærke:	Drayton
Kategori:	Smart hjem
Model:	miGenie Wish 3
Bredde:	148 mm
Dybde:	28 mm
Højde:	93 mm
Produktfarve:	Hvid
Batterispænding:	1.5 V
Opbevaringstemperatur (T-T):	-20 - 55 °C
Relativ luftfugtighed ved drift (H-H):	25 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	15 - 95 %
Driftstemperatur (T-T):	0 - 45 °C
Forbindelsesteknologi:	Trådløs
Certificering:	2006/95/EC, 2004/108/EC, 1999/5/EC R&TTE, 2013/56/EU, EN60730-1; EN60730-2-7; EN60730-2-9, EN 300 220-2; EN 301 489-3
Strømkilde type:	Vekselstrøm
Batteritype:	LR6(AA)
Indgangsspænding:	230 V
Grænseflade:	IR trådløs
Batteriets levetid:	2 År
Indgangsfrekvens:	50 Hz
Maksimal driftstilstand:	30 m
Temperatur måleområde:	5 - 30 °C
Frekvens:	868.3 MHz
Måle miljøforhold:	Temperatur