DSC BV-600 Manual

DSC Bevægelsesdetektor BV-600

Læs gratis den danske manual til DSC BV-600 (3 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 60 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 30.5 anmeldelser. Har du et spørgsmål om DSC BV-600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

The Bravo 6 is a specialized twin dual PIR motion sensor

which emphasizes immunity from false alarms caused by

pets. The Bravo 6 is equipped with a specially designed

lens

∗∗

∗

which enables the detector to discriminate between

humans and small to mid-sized pets.

Exceptional design care and factory testing ensure years

of trouble free performance. Immunity against false

alarms from RF, static, electrical transients and white

light are all DSC designed in features.

Multi-Level Signal Processing

∗∗∗∗

∗∗∗∗∗∗

, temperature

compensation and large multi-beam lens design means

the human target will not slip by unnoticed even on a hot

summer day.

Wall or corner mounting and vertical adjustment provide

application versatility, and your client will appreciate the

small size and elegant simplicity of the case design.

Features

• Immune to pets under 2.5 ft/0.75 m (up to 85 lbs/38 kg)

• Microprocessor based

• Advanced Multi-Level Signal (MLS) Processing∗∗∗∗

∗∗∗∗∗∗

• Twin, dual element, low noise sensors

• High level static protection

• High level transient protection

• UV stable lens

• High level of white light immunity

• Excellent RF immunity

• DSC Temperature compensation circuitry

• Harsh/Normal environment jumper

• LED on/off jumper

• Vertical adjustment

• SMD construction

• Super quiet operation

• Wall/Corner mounting

• Blends with any decor

• Compact size

∗∗

∗∗∗

Protected by one or more of the following patents:

Canada CA2196014, US 5923250

∗∗∗∗

∗∗

Protected by one or more of the following patents:

Canada 2099971, US 5444432

INSTALLATION INSTRUCTIONS

Dual PIR

Motion Detector

Specifications

• Operating voltage: 9.5 VDC to 14.5 VDC

• Supply voltage ripple: 3.0 VP-P @ 12 VDC

• Stand-by current: 16.5 mA

• Current in alarm (LED on): 17.5 mA

• Contact rating (alarm & tamper): 100 mA @ 24 VDC

• Alarm contact resistor in common: 28 ohm 0.25 W

• Operating temperature: 32°F to120°F / 0°C to 49°C

• Storage temperature: -40°F to140°F / -40°C to 60°C

• Operating humidity: 5% to 93% RH non-condensing

• Storage humidity: up to 99% RH non-condensing

• Radiated RF immunity:

20 V/m with 80% AM over range, 27MHz to 1.0GHz

• Conducted RF immunity:

10V with 80% AM over range 150kHz to 80MHz

• Static immunity: 15 kV

• Transient immunity: 2.4 kV @ 1.2 joules

• Walk detection speed: 0.5'/s to 10'/s (0.15 m/s to 3 m/s)

• Coverage angle (wall/wall lens): 100° maximum

• Vertical adjustment: +2° to -5°

• Mounting heights:

7' to 10.5' / 2.1m to 3.2m (nominal 7.5' / 2.3m)

Physical

Dimensions

4.9" H × 2.76" W × 1.75" D (124.5 mm × 70 mm × 44.5 mm)

Colour

White with white lens

Models

• BV-600/PBV-600: Form A alarm contact

• BV-601/PBV-601: Form A alarm contact & tamper switch

• BV-602/PBV-602: Form C alarm contact & tamper switch

Beam Patterns for Bravo 6 Series Lens

Side View

Top View

Locating the Detector

Select a detector location that will provide the coverage

required keeping in mind the following potential problems

Reflective Surfaces

Do not aim the detector at reflective surfaces such as

mirrors or windows as this may distort the coverage pattern

or reflect sunlight directly onto the detector.

Air Flow

Avoid locations that are subject to direct high air flow such

as near an air duct outlet.

Moisture

Do not locate the detector near sources of steam or oil.

The Sun

Do not aim the detector such that it will receive direct or

reflected (mirror) sunlight.

Obstruction

Do not limit the coverage by large objects within the

detection area such as plants or filing cabinets.

Pet Rejection

Do not aim the detector at a stairway which a pet has

access to.

Do not place furniture or objects higher than 3 ft / 0.9 m,

which a pet can climb onto (e.g. a cat on a couch), closer

than 7 ft /2.1 m to the detector.

Mounting

To open the case, use a small flat blade screwdriver and

gently push in the tab at the bottom of the case and pull the

cover straight out at the bottom. Loosen the printed circuit

board screw, and push the board up as far as it will go. Using

a small screwdriver, remove the appropriate knockouts for

the mounting screws. Remove the desired wiring entrance

knockouts located at the top or bottom of the backplate.

Mount the backplate.

Locate screws diagonally opposite to each other to prevent

case warpage.

Vertical Height Guide

7.0' / 2.1 m + 0.25

7.5' / 2.3 m 0.00

8.5' / 2.6 m - 0.50

9.0' / 2.7 m - 1.00

10.5' / 3.2 m - 1.50

Vertical Adjustment

NOTE: Range and dead zones may vary due to settings.

Using the Mounting Height chart, set the vertical adjustment

to get the desired coverage. Ensure that the PCB retaining

screw is tightened just enough to prevent board movement.

Moving the circuit board DOWN will increase the far range

and move the near beams farther out from the mounting

wall. Moving the circuit board UP will reduce the far range

and bring the near beams closer to the mounting wall.

Moving the circuit board DOWN too much will cause the far

beams to “look” above the target; as a result, the range may

appear shorter.

Jumper J1 will enable/disable the alarm LED. If J1 is OFF,

the LED will not operate on alarm. If J1 is ON, the LED will

operate on alarm. Jumper J2 selects between harsh and

normal environments. For a typical environment or one

containing a small pet lower than 1.2 ft / 0.36 m, set the unit

as normal (J2 ON). For a large pet and multiple pets, the

jumper J2 should be removed.

Wiring

NOTE: This unit is UL Listed and should be connected

to a listed control unit or power supply providing at

least 4 hours of standby power.

Walk Testing

Once the detector has been set up, walk test the entire

area where coverage is desired. Should the coverage be

incomplete, readjust or relocate the detector to obtain full

coverage. Once coverage is as required, the alarm LED

may be disabled by setting J1 to OFF.

IMPORTANT NOTE: Upon installation, the unit should

be thoroughly tested to verify proper operation. The

end user should be instructed on how to perform walk

tests, and should walk test the detector weekly.

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of twelve months from the

date of purchase, the product shall be free of defects in materials and workmanship

under normal use and that in fulfilment of any breach of such warranty, Digital

Security Controls Ltd. shall, at its option, repair or replace the defective equipment

upon return of the equipment to its repair depot. This warranty applies only to defects

in parts and workmanship and not to damage incurred in shipping or handling, or

damage due to causes beyond the control of Digital Security Controls Ltd. such as

lightning, excessive voltage, mechanical shock, water damage, or damage arising

out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in

lieu of any and all other warranties, whether expressed or implied and of all other

obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security

Controls Ltd. neither assumes, nor authorizes any other person purporting to act on

its behalf to modify or to change this warranty, nor to assume for it any other

warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or

consequential damages, loss of anticipated profits, loss of time or any other losses

incurred by the buyer in connection with the purchase, installation or operation or

failure of this product.

Motion detectors can only detect motion within the designated areas as shown in

their respective installation instructions. They cannot discriminate between intrud-

ers and intended occupants. Motion detectors do not provide volumetric area pro-

tection. They have multiple beams of detection and motion can only be detected in

unobstructed areas covered by these beams. They cannot detect motion which oc-

curs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or

windows. Any type of tampering whether intentional or unintentional such as mask-

ing, painting, or spraying of any material on the lenses, mirrors, windows or any

other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in temperature. How-

ever their effectiveness can be reduced when the ambient temperature rises near or

above body temperature or if there are intentional or unintentional sources of heat in

or near the detection area. Some of these heat sources could be heaters, radiators,

stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.

Warning: Digital Security Controls Ltd. recommends that the entire system be

completely tested on a regular basis. However, despite frequent testing, and due

to, but not limited to, criminal tampering or electrical disruption, it is possible for

this product to fail to perform as expected.

Important Information: Changes or modifications not expressly approved by Digital

Security Controls Ltd. could void the user’s authority to operate this equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement

sur le matériel brouilleur du Canada.

NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.

Toronto, Canada

Tech Line 1-800-387-3630 (Canada & US) • www.dsc.com

Printed in Canada 29034622 R001