DSC WS4939 Manual

DSC Fjernbetjening WS4939

Læs gratis den danske manual til DSC WS4939 (2 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 29 anmeldelser. Har du et spørgsmål om DSC WS4939, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Panasonic

CR2025

WS4939 Wireless Key

Operating Instructions

Congratulations on the purchase of the WS4939, DSC's newest 4

button wireless key. This key will allow you to arm and disarm, as well

as other keypad functions with the convenience of wireless portabil-

ity. Together with your installer, you can decide which functions you

wish to have accessible from your portable key.

To activate, press and hold the appropriate button for approximately

1 second*. The LED located between buttons 1 and 2 will confirm

that a signal has been sent to the control panel receiver.

*False Alarm Prevention

By default, the key is a panic key. It will require the user to press

and hold for approximately 3 seconds. This was designed to reduce the possibility of a

false alarm

NOTE: Signals will not be received if the key is not within the range of the wireless receiver.

The default functions are as follows:

Stay Arming

Press this button to arm your system in the Stay mode. All perimeter

zones will be armed, such as all window and door contacts, but the inte-

rior zones will remain inactive, allowing you to stay on the premises with-

out setting off an alarm.

Away Arming

Press this button to arm your system in the Away mode. Both the interior

and exterior zones will be armed, allowing you to exit the premises.

Disarm

Press this button to disarm your system. You do not have to enter your

access code when you use the key to disarm the system.

Panic

Press this button to notify your central monitoring station of a situation

requiring the police, such as a break-in.

Other options are available. Please discuss all WS4939 options with your installer in order

to program the best possible combination to suit your needs. As well for your conve-

nience an optional rubber button insert has been included.

Replacing the Batteries

Under normal conditions the batteries can last from 5 to 8

years. During each button press the key will send the status of

its battery to the control panel receiver. If the battery is low the

trouble light on the controls panel's keypad will turn ON.

To replace the battery, remove the top cover by inserting a coin into

the slot located on the bottom right corner and twist. Remove the screw at the center of

the board to expose the batteries. Replace both batteries with Panasonic CR-2025 lithium

batteries (see above diagram).

NOTE: The polarity of the battery must be observed, as shown in the diagram above.

Improper handling of lithium batteries may result in heat generation, explosion or fire,

which may lead to personal injuries.

LED

WS4939 Wireless K

WARNING: DANGER OF EXPLOSION IF BATTERIES ARE INSTALLED INCORRECTLY.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANU-

FACTURER.

Keep away from small children. If Batteries are swallowed, promptly see a doctor. Do not try to

recharge these batteries. Disposal of used batteries must be made in accordance with the waste recov-

ery and recycling regulations in your area.

Note to Installer

Removing the 3-Second Delay on the Panic ( ) Key

Changing the programming will affect operation. This should be done by the installer.

•Press and hold all 4 buttons simultaneously until the LED begins to flash.

•Press the Away key ( ).

•These are toggle features, to return to default, repeat the steps above.

NOTE: Do not press any other button while in Programming mode.

NOTE: For UL Listed installations, the 'Arm/Disarm Bell Squawk" feature of the control

panel must be enabled. The 3-second delay on the Panic key must not be disabled. The Bell

Squawk must be heard from outside the premises. Refer to the control panel's Installation

Manual for more information.

Belt Clip Assembly

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of 12 months from the date of purchase, the product shall be free of defects

in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd.

shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies

only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the

control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising

out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether

expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security Controls

Ltd. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this

warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of anticipated profits,

loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.

Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis. However, despite

frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to per-

form as expected.

Important Information: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void the user’s

authority to operate this equipment.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use

this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undes-

ired operation.

IC: 160A-WS4939 The term ‘IC:’ before the radio certification number only signifies that Industry Canada technical specifications

were met.

Technical Support: 1-800-387-3630 • www.dsc.com

Printed in Canada 29007005 Rev 001

Direct all comments concerning this publication to pubs@dscltd.com

Compatibility

The WS4939 is compatible with the following

receivers: PC4164-433, PC5102-433, PC5132-

433, RF5108-433, RF5501-433, NT9005 and

the NT9010.

The WS4939 enrolls the same way as the

WLS919, please refer to the receiver manual

for details.

Produkt Specifikationer

Mærke:	DSC
Kategori:	Fjernbetjening
Model:	WS4939

Har du brug for hjælp?

Hvis du har brug for hjælp til DSC WS4939 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening DSC Manualer

DSC WS4949 Manual

8 Oktober 2024

DSC WS4939 Manual

1 September 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

Insignia NS-RMT8D21 Manual

29 September 2025

ProMaster PRO5439 Manual

29 September 2025

Insignia NS-RMTVIZ21 Manual

29 September 2025

ProMaster PRO7599 Manual

29 September 2025

ProMaster PRO1782 Manual

29 September 2025

ProMaster PRO7337 Manual

29 September 2025

ProMaster PRO7606 Manual

29 September 2025

Neets 310-0350 Manual

29 September 2025

Nikon MC-DC3 Manual

28 September 2025

Neets 310-0202 Manual

27 September 2025