Electro-Voice EVH-1152S/99 Manual

Electro-Voice Højttaler EVH-1152S/99

Læs gratis den danske manual til Electro-Voice EVH-1152S/99 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Electro-Voice EVH-1152S/99, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
EV-I Access Card
Access Card for Plug-In
Loudspeaker Diagnostics
User Instructions
Tools Required:
Instructions:
1. #2 Phillips Screwdriver 2. Ohm Meter capable of accurate
measurements below 50 ohms
#2
1. If applicable, remove screws holding the security cover, gland nut cover, or NL4 cover in
place. Note position of the switch card. The card must be replaced in exactly the same
position as it was originally or system performance will be adversely affected!
2. Carefully remove the switch card and set it aside. Plug the Access Card onto the header in
place of the switch card. Note that the Access Card, unlike the switch card, will only fit in
one position centered on the input cup (See Figure 1).
3. Turn on the Ohm Meter and set it to the low ohms (x1) scale. Short the two probes togeth-
er and calibrate the meter to “Zero” (See Figure 2). If your meter does not have this calibra-
tion feature, note the ohms reading. This is the residual internal resistance of the meter,
probes and test leads. You will need to DEDUCT this number from the results you measure
at the Access Card.
The Access Card is a unique feature of the EV-Innovation series loudspeaker families. This
simple plug-in device allows diagnostic access to the transducers and protection circuitry
inside the enclosure WITHOUT requiring any disassembly or disconnections beyond simple
removal and replacement of the plug-in switch card. DCR values described in these instruc-
tions are typical for EV-I series two-way systems (eg: EVF-1122S/64). For complete model-
specific DCR values, consult the chart on page 4.
Figure 1:
Switch Card Removal / Access Card Install
Figure 2:
Ohm Meter Calibration
Adjust
0.0
<50.0

Produkt Specifikationer

Mærke: Electro-Voice
Kategori: Højttaler
Model: EVH-1152S/99

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice EVH-1152S/99 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Electro-Voice Manualer

Electro-Voice

Electro-Voice ZLX‑15P‑G2 Manual

4 August 2025
Electro-Voice

Electro-Voice Evid 4.2T Manual

30 Juli 2025
Electro-Voice

Electro-Voice EVID 6.2 Manual

29 Juli 2025
Electro-Voice

Electro-Voice EVH-1152S/99 Manual

22 Januar 2025
Electro-Voice

Electro-Voice XLE191-FG Manual

8 Januar 2025
Electro-Voice

Electro-Voice Sx600 Manual

8 Januar 2025
Electro-Voice

Electro-Voice Sb122 Manual

8 Januar 2025
Electro-Voice

Electro-Voice Tour X TX1122FM Manual

2 Oktober 2024
Electro-Voice

Electro-Voice EVID C10.1 Manual

2 Oktober 2024
Electro-Voice

Electro-Voice EVID-40C Manual

19 September 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Canton

Canton Atelier InWall 9 C Manual

16 November 2025
Martin

Martin M72i Manual

16 November 2025
Martin

Martin Outdoor ViroSphere Manual

15 November 2025
Martin

Martin ViroSphere Manual

15 November 2025
Nady

Nady P-Cab PCS-15X Manual

15 November 2025
TDK

TDK V513 Manual

15 November 2025
Valcom

Valcom VIP-148AL-IC Manual

15 November 2025
Canton

Canton Atelier InWall 11 C Manual

14 November 2025
Martin

Martin M129i Manual

14 November 2025
Martin

Martin CM12 Manual

14 November 2025