Electro-Voice XLE191-FG Manual

Electro-Voice Højttaler XLE191-FG

Læs gratis den danske manual til Electro-Voice XLE191-FG (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Electro-Voice XLE191-FG, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

X-Line Very Compact

Crossover Retrofit

Installation Instructions

YOU WILL NEED:

- ONE SHORT-HANDLED PHILLIPS SCREWDRIVER

- ONE SHORT-HANDLED ¼” NUT DRIVER

- SMALL SCRAPER OR PUTTY KNIFE

- SMALL WIRE (SIDE) CUTTER TO SNIP CABLE TIES

- CARPENTERS’ WOOD GLUE

- 3M SUPER 77 SPRAY ADHESIVE OR LIQUID

CONTACT CEMENT

1) REMOVE THE 6 SCREWS HOLDING THE INPUT PANEL. CAREFULLY UNPLUG THE MOLEX CONNECTOR

FOR THE TRANSDUCER WIRING AND PEEL OFF THE CONTACT INFORMATION LABEL COVERING THE

“BIAMP” INDICATOR WINDOW ON XLD OR “PASSIVE” INDICATOR WINDOW ON XLE.

2) REMOVE THE GRILLE.

3) REMOVE THE WOOFER THAT SHARES THE SAME CHAMBER AS THE INPUT PANEL.

4) STAND THE ENCLOSURE ON ONE END WITH THE NOW OPEN CHAMBER ON TOP. REMOVE THE BATTING

FROM THIS CHAMBER AND DISCARD.

5) USING THE ¼” NUT DRIVER, UNSCREW THE TWO CABLE TIES SECURING THE WIRES TO THE DIVIDER

PANEL. SAVE THE SCREWS.

6) CAREFULLY SNIP THROUGH THE CABLE TIES TO FREE THE WIRES FROM THEIR BUNDLE, TAKING CARE

NOT TO DAMAGE THE INSULATION ON THE WIRES.

7) SCRAPE OFF ANY EXCESS GLUE DRIBBLES, ADHESIVE AND LEFTOVER BATTING FROM THE SIDEWALLS

OF THIS CHAMBER, ESPECIALLY THE DIVIDER PANEL. TAKE CARE NOT TO ALLOW WIRING TO BE

DAMAGED BY YOUR SCRAPER BLADE. DO NOT DISTURB CAULKING MATERIAL IN WIRING THRU-HOLE

TO HF CHAMBER. IF YOU DO, IT MUST BE RE-SEALED WITH SILICONE RTV CAULK.

8) NOTE THE CHANNELS MILLED INTO ONE SIDE OF THE NEW MOUNTING BOARD. (THE SIDE WITH THE T-

NUTS SHOWING) APPLY AN EVEN LAYER OF WOOD GLUE TO THE FLAT AREAS ADJACENT TO THESE

CHANNELS. (SEE FIGURE 1)

Glue

Rounded Corner

Glue

Rounded Corner

Glue

000-649103 TSILSTRAPTIFORTERREVOSSORCE/DLX

N/P NOITPIRCSED .YTQ

000-080207 DRAOBGTMTIFORTERREVOXE/DLX 1

000-804065 E/DLX,REVOX 1

90883 NOLYN,TALF,REHSAW 7

PCL412706 8

/7X42-01,WERCS 7

31437 EITELBAC 1

000-126195 GNITTAB FL1

000-141185 WERCSLLAWYRD”¼1x8# 6

47401183 TIFORTERREVOXE/DLX,SNOI

TCURTSNI 1

This End of Mounting Board

to Rear of Enclosure

T-Nuts

Figure 1: Apply Glue to Mounting Board

Channel

Produkt Specifikationer

Mærke:	Electro-Voice
Kategori:	Højttaler
Model:	XLE191-FG

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro-Voice XLE191-FG stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Electro-Voice Manualer

Electro-Voice EVH-1152S Manual

20 November 2025

Electro-Voice ZLX-G2 Manual

19 November 2025

Electro-Voice ZLX‑15P‑G2 Manual

4 August 2025

Electro-Voice Evid 4.2T Manual

30 Juli 2025

Electro-Voice EVID 6.2 Manual

29 Juli 2025

Electro-Voice EVH-1152S/99 Manual

22 Januar 2025

Electro-Voice XLE191-FG Manual

8 Januar 2025

Electro-Voice Sx600 Manual

8 Januar 2025

Electro-Voice Sb122 Manual

8 Januar 2025

Electro-Voice Tour X TX1122FM Manual

2 Oktober 2024

Højttaler Manualer

Nyeste Højttaler Manualer

Defender Melis Manual

19 November 2025

Soundcore Motion+ Manual

19 November 2025

Thomson WS202T Manual

19 November 2025

TDK TP6701BLK Manual

18 November 2025

Martin CN12 Manual

18 November 2025

Canton Atelier InWall 9 C Manual

16 November 2025

Martin M72i Manual

16 November 2025

Martin Outdoor ViroSphere Manual

15 November 2025

Martin ViroSphere Manual

15 November 2025

Nady P-Cab PCS-15X Manual

15 November 2025