Eliminator Lighting Stealth Craze Manual


Læs gratis den danske manual til Eliminator Lighting Stealth Craze (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Eliminator Lighting Stealth Craze, eller vil du spørge andre brugere om produktet?

Side 1/6
STEALTH CRAZE
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Introduction:
The Stealth Craze is a unique DMX intelligent moving head unit. The Stealth Craze has 3 operating
modes; sound active mode, show mode, or controlled via DMX controller. The Stealth Craze has 2
DMX Channel modes; 5 or 16 channels. The unit can be run as a stand alone unit or in a Master/
Slave set up. This unit has been tested and there is no assembly required. Follow the instructions
on the following pages to operate your fixture. To enhance the beams effects you can use a fog
machine.
CAUTION! Please read and understand these instructions before installing or operating this unit.
SPECIFICATIONS:
Model: Stealth Craze
Supply Voltage: 100V-240V 50/60Hz
LED: 4 x 10W White LED’s
Weight: 10lbs./ 4.5 kgs.
Size: 6.69” (L) x 9.4” (W) x 12.63” (H)
Fuse: 2 Amp
Power Consumption: 55W
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 2 DMX Channel Modes:
5 Channel Mode &
16 Channel Mode
Colors: 3 Colors + White
Warranty: 1 Year
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Fuse Replacement: Locate and remove
the unit’s power cord. Once the cord
has been removed, the fuse holder is
located inside the power socket. Insert
a flat-head screw driver into the fuse
holder and gently pry out the holder.
Remove the bad fuse and replace with
a new one. The fuse holder has a built-in
second holder for a spare fuse.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
AXXX: In this menu you can set the DMX address. Press the Up or Down buttons until “AXXX” is displayed.
“XXX” is the current displayed DMX address. Press Enter and use the UP or Down buttons to nd your de-
sired address. When you have found your desired address press the Enter button to set it. NOTE: To display
the DMX address you must rst select any show, then press the MENU button to exit and then follow
the directions above.
Chnd: The Stealth Craze has 2 DMX channel modes; 5 channel mode and 16 channel mode. In this menu you
can select your desired channel mode. Press the Up or Down buttons until “CHnd” is displayed and press
ENTER. Either “16CH” or “5CH” will be displayed. Use the Up and Down buttons to toggle between the two
modes and press Enter to make your selection and press Menu to exit.
SPnd (Sound Active Speed): In this menu you can adjust the sound active moving speed. Press the Up or
Down buttons until “SPnd” is displayed and press ENTER. Either “LoSP” (Low Speed) or “HISP” (High Speed)
will be displayed. Use the Up and Down buttons to toggle between the two speed and press Enter to make
your selection. Press the Menu button to exit.
SOUN (Sound Active): In this menu you can activate Sound Active mode. Press the Up or Down buttons until
“SOUN” is displayed and press Enter. Either “On” or “O” will be displayed. Use the Up and Down buttons
toggle between the choices and press Enter to make your selection. Press the Menu button to exit.
SHnd (Show Mode): In this menu you can activate the 1 of 8 show mode’s. Press the Up or Down buttons
until “SHnd” is displayed and press Enter. Either 1 of 8 shows will be displayed. Use the Up and Down but-
tons nd your desired show and press Enter to make your selection. Press the Menu button to exit
SLnd (Master/Slave): In this menu you can designate the xture as either a Master or Slave in a master-slave
set up. Press the Up or Down buttons until “SLnd” is displayed and press Enter. Either “Mast” or “SL 1 will be
displayed. Use the Up and Down buttons to nd your desired setting and press Enter to make your selection.
Press the Menu button to exit
PAn (Reverse Pan): In this menu you can reverse the Pan function. Press the Up or Down buttons until “PAn”
is displayed and press Enter. Press the Up or Downs buttons until “On” is
displayed, and press Enter. Press the Menu button to exit. This function works better when you have two units
connected in a Master/Slave setup. Have one unit set to reverse Pan and the other unit in normal Pan.
tIL ( Reverse Tilt): In this menu you can reverse the Tilt function. Press the Up or Down buttons until “tIL” is
displayed and press Enter. Press the Up or Downs buttons until “On” is
displayed, and press Enter. Press the Menu button to exit. This function works better when you have two units
connected in a Master/Slave setup. Have one unit set to reverse Tilt and the other unit in normal Tilt.
dISP (Display): In this menu you can “ip” the display 180°. Press the Up or Down buttons until “dISP” is
displayed and press Enter. Either “ON” or “OFF” will now be displayed. If you want to “ip” the display press
the Up button so that “ON” is displayed, and press Enter. Press the Menu button to exit.
rSt (Reset): In this menu you can activate reset function. Press the Press the Up of Down buttons until “rSt
is displayed and press Enter. The unit will now begin to reset. Press the Menu button to exit.
rFAC (Default Setting): In this menu you can reset the unit to it default settings. Press the Up or Down but-
tons until “rFAC” is displayed and press Enter. Select “On” and press Enter. Press the Menu button to exit.


Produkt Specifikationer

Mærke: Eliminator Lighting
Kategori: Ikke kategoriseret
Model: Stealth Craze

Har du brug for hjælp?

Hvis du har brug for hjælp til Eliminator Lighting Stealth Craze stil et spørgsmål nedenfor, og andre brugere vil svare dig