Elkay LK4420 Manual

Elkay Vanddispenser LK4420

Læs gratis den danske manual til Elkay LK4420 (4 sider) i kategorien Vanddispenser. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Elkay LK4420, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

PAGE 1

4420_FTN_A LK4420_FTN_A

1000003683 (Rev. B - 12/17)

Owners Manual

Model 4420

Bi-Level Tubular Fountain

INSTALLER

4420 Fountains are among the easiest to install Fountains on the market today.

To assure you install these models easily and correctly, PLEASE READ THESE

SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR

INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER

APPLICABLE CODES. After installation, leave these instructions with the Fountain for

future reference.

PAGE 21000003683 (Rev. B - 12/17)

4420_FTN_A LK4420_FTN_A

1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting structure

must be capable of supporting 300 lb. load on fountain.

2. Refer to rough-in for plumbing.

3. Install shut-off valve on water supply. (Valve not furnished)

4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished)

5. Connect water supply and fountain drain. Connect drain waste "Tee" to fountain drain tubes. Connect outlet of "Tee" to

drainage system. Water connection and drain must comply with local codes.

6. Turn on water supply and check all connections for leaks.

CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the

inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line

pressures lower than 20 PSI or higher than 105 PSI is not covered by warranty.

7. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. Contractor to supply waste trap and service stop valve in

accordance with local code.

8. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being

connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color,

or sediment problems.

9. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and the

fountain. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive

stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE

O-RINGS MAY RESULT.

INSTALLATION INSTRUCTIONS

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

TROUBLE SHOOTING AND MAINTENANCE

ACTUATION OF QUICK CONNECT WATER FITTINGS:

Fountain is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the tting, relieve

water pressure, push in on the gray collar while pulling on the tubing. (see Fig.2) To insert tubing, push tube straight into

tting until it reaches a positive stop, approximately 3/4".

B CA

SIMPLY PUSH IN

TUBE IS SECURED

PUSH IN COLLET

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B C

1/4” O.D. TUBE

WATER INLET

TO COOLER

3/8” O.D. TUBE CONNECT

COLD WATER SUPPLY

BUILDING WATER

INLET

NOTE: WATERFLOW

DIRECTION

SERVICE STOP

(NOT FURNISHED)

FIG 1 FIG 2

Produkt Specifikationer

Mærke:	Elkay
Kategori:	Vanddispenser
Model:	LK4420

Har du brug for hjælp?

Hvis du har brug for hjælp til Elkay LK4420 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vanddispenser Elkay Manualer

Elkay LVRCGRN8 Manual

22 August 2025

Elkay LK4595SFR Manual

21 August 2025

Elkay MB30 Manual

21 August 2025

Elkay LZO8L Manual

21 August 2025

Elkay EDFPBM117K Manual

16 Juni 2025

Elkay LK4420 Manual

9 Juni 2025

Elkay LZS8SF Manual

8 Juni 2025

Elkay LZS8L Manual

7 Juni 2025

Elkay LVRCTL8SC Manual

7 Juni 2025

Elkay LWTLA14S3K Manual

7 Juni 2025

Vanddispenser Manualer

Nyeste Vanddispenser Manualer

Livoo PET108 Manual

24 September 2025

Follett 25CI425W-Li Manual

17 September 2025

Follett 50CI425A-S Manual

17 September 2025

Follett 50CI425A-LI Manual

17 September 2025

Follett 50CI425A-SI Manual

17 September 2025

Vestel SP 313-AG Manual

17 September 2025

Vestel SP 202-A Manual

17 September 2025

Vestel SP 200 Manual

17 September 2025

Follett 50CI425W-S Manual

16 September 2025

Vestel SP 201-G Manual

16 September 2025