Emga 721100 Manual

Emga Skæremaskine 721100

Læs gratis den danske manual til Emga 721100 (7 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Emga 721100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

English

Operator’s Manual

InstaslIce

Series 15100

15200

Thank you for purchasing this Vollrath Food Processing Equipment. Before operating the equipment, read and familiarize yourself with

the following operating and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and

packaging. Use this packaging to ship the equipment if repairs are needed.

721100 G20E

1/7

S Pafety recautionS

To ensure safe operation, read the following statements and

understand their meaning. This manual contains safety precautions

which are explained below. Please read carefully.



Warning is used to indicate the presence of a hazard that can cause

severe personal injury, death, or substantial property damage if the

warning is ignored.



Caution is used to indicate the presence of a hazard that will or can

cause minor personal injury or property damage if the caution is

ignored.



Note is used to notify people of installation, operation, or

maintenance information that is important but not hazard-related.



These precautions should be followed at all times. Failure to follow

these precautions could result in injury to yourself and others or

damage the equipment.

To reduce risk of injury or damage to the equipment:

Check equipment before each use to insure the equipment is clean.

Check for broken, nicked or dull blades and if found, replace blade

assembly.

Check to insure that the pusher head sits down completely on the

rubber bumpers. The suction cups on each rear leg will hold the

equipment securely to smooth surfaces.

If necessary, lubricate guide rods using a light coating of mineral oil,

Petro Gel, or food grade lubricant. DO NOT USE COOKING OIL AS

IT WILL BECOME STICKY AND MAY PERMANENTLY DAMAGE THE

PUSHER HEAD BEARINGS

f Punction and urPoSe

Intended for slicing of tomatoes.

oPeration





Blades are sharp and can cause cuts and

amputation.

To avoid injury from sharp blades, handle with caution. Only trained

personal should operate equipment or preform maintenance.

Prior to rst use, it is important to clean the equipment. Wash new blades

with warm soapy water and rinse thoroughly to remove the thin protective oil

lm.

1. Place slicer on a table or counter. Position the InstaSlice Table Stop over

a table edge to hold the equipment in place

2. Before each use, always check for proper blade tightness and equipment

cleanliness. Check for broken, nicked or dull blades and if found, replace

blade assembly.

3. This equipment should be used to slice soft vegetables such as

tomatoes, mushrooms, strawberries, etc. Hard foods such as onions,

potatoes, lemons, etc. will cause blades to break. Use a Tomato King

Scooper to remove the stem scar of the tomato. For best results, the

tomatoes should be clean and wet before slicing them in the equipment.

4. Spray the plastic platform and blades with water to reduce friction and

repeat as needed during use.

5. Place the tomato top down on the platform of the slicer against the

pusher head. Place one hand on the pusher head handle and one hand

on the knob on top of the slicer. With a quick push of the pusher head,

push the tomato through the blades catching the slices into a pan placed

at the end of the slicer.

6. Repeat this process until you have prepared enough food for your daily

needs.

7. Rinse blades immediately. Failure to do so will shorten the life of the

blades.

cleaning





Blades are sharp and can cause cuts and

amputation.

To avoid injury from sharp blades, handle with caution. Only trained

personal should operate equipment or preform maintenance.

To maintain the appearance and increase the service life, clean your daily.

1. Place Pusher Head Assembly in its most “open” position by retracting the

handle.

2. Rinse or spray off equipment thoroughly with HOT water. You may want

to immerse the complete equipment in warm soapy water rst. Use

caution when handling the equipment - blades are sharp.

3. Do not wipe across blades or use scrub pads on this equipment. Wiping

across the sharp edge of the blade can cause injury and will dull the

blades.

4. Do not put this equipment in a dishwasher or dish machine with soaps,

detergents, or other alkaline chemicals that can harm the equipment.

5. After cleaning, let the equipment air dry.

6. Lubricate sliding parts with mineral oil or Petro Gel after each use.

Do not use cooking oil as it will become sticky and may permanently

damage the equipment.









721100 G20E

2/7

Produkt Specifikationer

Mærke:	Emga
Kategori:	Skæremaskine
Model:	721100

Har du brug for hjælp?

Hvis du har brug for hjælp til Emga 721100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Emga Manualer

Emga 721100 Manual

28 August 2024

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Vollrath 40900 Manual

30 September 2025

Vollrath 40901 Manual

30 September 2025

Fry Factory AFC-50 Manual

28 September 2025

Jaccard Fillet-O-Matic Manual

28 September 2025

Jaccard VA 2000 Manual

28 September 2025

JAC Pico Manual

26 September 2025

Axis VOLANO 12 RED Manual

23 September 2025

Lincoln Electric Tomahawk 1500 Manual

23 September 2025

Chefman RJ49 Manual

23 September 2025

Eta Tempo 1094 90000 Manual

21 September 2025