Emko DT-9910 Manual

Emko Ikke kategoriseret DT-9910

Læs gratis den danske manual til Emko DT-9910 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Emko DT-9910, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Operating Temperature : 0 to 50 °C

Differantial controller gives output to calculate temperature difference between two sensor.

Easy access to the screen to adjust the setpoint and code protected the parameter menu

for parameter settings. If temperature difference between two sensor becomes equals or more

according to adjust setpoint and hysteresis parameter,the relay output is activated, otherwise

the relay output is disabled.

Instruction Manual. ENG DT-9910 01 V02 07/14

- 3 Digits display

- 2 PTC inputs

- 2 Relay outputs

- ON/OFF control form

- Limitation of setpoint

- Hysteresis adjustment

- Programming mode password protection

- Easy access to setpoint changing the screen

- Boiler water over-temperature protection

- Collector frost protection

DIFFERENTIAL CONTROLLER

: %90 Rh (non-condensing)

2000 m’ye kadar

1.2. General Specifications

1.Introduction

1.1 Environmental Ratings

PTC

2. Front View and Dimensions of DT-9910 differential Controller with Two Relays

1.3 Installation

Cooling Controller

ECC 200

6 m /7 in h9 m 3 . 8 c

96 mm / 3.78 inch

12 ± 1 mm / 0.47 inch 84 mm / 3.34 inch

Maksimum 15 mm / 0.59 inch

Standard

EMKO

DIFFERANTIAL CONTROLLER

Max. Operating Humidity

Altitude :

Forbidden Conditions : Corrosive atmosphere

Explosive atmosphere

Optional Supply Voltage Inputs

Supply Voltage Inputs

2 Temperature Sensor

Inputs

Pump output

Heater output

Pump output

Heater output

Repair and Maintenance Service Information:

Manufacturer Information:

1.4 Warranty

1.5 Maintenance

1.6 Manufacturer

Emko Elektronik Sanayi ve Ticaret A. .

Demirta Organize Sanayi Bölgesi Karanfil Sk.No:6 16369 BURSA

Tel : (224) 261 19 00 Fax : (224) 261 19 12

Emko Elektronik Sanayi ve Ticaret A. .

Demirta Organize Sanayi Bölgesi Karanfil Sk.No:6 16369 BURSA

Tel : (224) 261 19 00 Fax : (224) 261 19 12

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for period of two years. The warranty period starts from the

delivery date. This warranty is in force if duty and responsibilities which are determined in warranty

document and instruction manuel performs by the customer completely.

Repairs should only be performed by trained and specialized personel. Cut power to the device before

accesing internal parts.

Do not clean the case with hydrocarbon-based solvents(Petrol,Trichlorethylene etc.). Use of these

solvents can reduce the mechanical reliability of the device. Use cloth dampened in ethyl alcohol or

water to clean the external plastic case . Average lifetime of the device 10 years.



Before beginning installation of this product, please read the instruction manuel and warnings below

carefully.

A visual inspection of this product for possible damage occured during shipment is recommend before

installation. It is your responsibility to ensure that qualified mechanical and electrical technicians install

this product.

If there is danger of a seriour accident resulting from a failure or defect in this unit, power off the system

and seperate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse as

required.

Be sure the use the rated power supply voltage to protect the unit against damage and to prevent failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can

be prevent.

Never attemp to disassemble , modify or repair this unit . Tampering with the unit may results in

malfunction, electric shock or fire.Do not use the unit in combustible or explosive gaseous atmospheres.

During the equipment is putted in hole on metal panel while mechanical installation some metal burrs

can cause injury on hands, you must be careful.

Montage on the product on a system must be done with it’s fixing clambs. Do not to the montage of the

device with inappropriate fixing clamb . Be sure t hat the device will not fall while doing the montage.

It is your responsibility if this equipment is used in manner not specified in this instruction manuel.



Produkt Specifikationer

Mærke:	Emko
Kategori:	Ikke kategoriseret
Model:	DT-9910

Har du brug for hjælp?

Hvis du har brug for hjælp til Emko DT-9910 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Emko Manualer

8 September 2025

8 September 2025

8 September 2025

8 September 2025

Emko TRANS MAINS Manual

8 September 2025

8 September 2025

8 September 2025

8 September 2025

8 September 2025

Emko Trans-MidiAUTO Manual

7 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Wolf 801642 Manual

28 December 2025

Daikin EKBPH010N Manual

28 December 2025

RYOBI One+ RDA18 Manual

27 December 2025

Deye SUN-6K-SG02LP2-US-AM2 Manual

27 December 2025

Aconatic AN-TT7540 Manual

27 December 2025

Anova P10B Manual

27 December 2025

Biltema 25-8844 Manual

27 December 2025

Gamdias Aura GL360 Lcd Manual

27 December 2025

Grässlin talento 111 SK Manual

27 December 2025

Yamazen SUT-202 Manual

27 December 2025